3M Digital Media System 710 Operating Manual

							31 3M
™ Digital Media System 700 Series
© 3M 2007. All Rights Reserved.
ENGLISH
Troubleshooting
Troubleshooting (continued)
Audio and Image Issues
Before requesting repair, please check in accordance with the following chart. If the situation cannot be 
corrected, then contact your dealer.
Problem Cause / Solution
Power does not come ON.The main power source is not ON.
The electrical power cord is not plugged in.
The main power source has been interrupted during operation, such as by a 
power outage (blackout), etc.
Be sure to press the "O" (power OFF) side of the main power switch, 
and leave this OFF for at least 20 minutes. After the unit has sufficiently 
cooled down, turn ON the power source.
No sound or image output.The input changeover settings are mismatched.
Select the input signal, and correct the changeover settings.
No signal input.
Correctly connect the connection cables.
Pictures are displayed, but no 
sounds are heard.The electrical wiring to this unit is not correctly connected.
Correctly connect the connection cables.  
The volume setting has been set at (or adjusted to) an extremely low level.
Adjust the VOLUME setting to a higher level.   
The MUTE mode is the current setting.
Press the MUTE button to release (change) the MUTE mode setting.
Sounds are heard, but no pictures 
are displayed.The electrical wiring to this unit is not correctly connected.
Correctly connect the connection cables.  
The brightness setting has been set at (or adjusted to) an extremely low level.
Adjust the BRIGHT setting to a brighter level.   
The lens cap has not been removed.
Remove the lens cap.   
Cannot play DVD.Make sure the DVD player's LED indicator is lighting.
Confirm that the disc is an original edition.
Eject the disc and play again.
Press "Menu" button while the projector is detecting the source, then press 
"Enter" button to reboot the DVD player.
ENGLISH 
						

							32
3M™ Digital Media System 700 Series
© 3M 2007. All Rights Reserved.
ENGLISH
Maintenance
Maintenance
Replacing Projection Lamp
When the lamp’s total working time accumulates to over 2000 hours, the on-screen display (OSD) will deliver a 
message recommending that you replace the lamp. Please contact a service center to replace the lamp as soon as 
possible, or refer to the following instructions to replace it yourself.
To replace the lamp:
1. Turn off the projector by pressing the “power” button on top of the unit.
2. Allow the projector to cool down for at least one hour.
3. Switch off the main power and disconnect the power cord.
4. Loosen two screws on the lamp cover and remove the lamp cover.
5. Loosen the screw on the lamp module. Remove the lamp module by pulling on the handle.
6. Insert a new lamp module into the socket; make sure it is in position.
7. Reverse step 4 and 5.
8. Ensure that the lamp cover is securely attached and flush with the bottom of the unit. The unit will not 
operate with the cover incorrectly installed.
9. Reset the lamp timer.
3M™ Digital Media System 700 Bottom View 
						

							33 3M
™ Digital Media System 700 Series
© 3M 2007. All Rights Reserved.
ENGLISH
Specifications
Specifications
Note: These specifications are subject to change without notice.
Optical
Resolution: Native, True XGA (1024 x 768)
Imager: One panel 0.7" DLP projection system
Aspect Ratio: 4:3 native and 16:9 supported
Colors: 16.7 million true colors (24 bit)
Brightness: 1500 ANSI lumens – optimal for Vikuiti™ Super Close Projection
Contrast Ratio: 1300:1
Projection lens: Manually adjustable focus, 130% offset, F2.4
Projection Image Size: From 40" to 100"
Digital Zoom: Excellent quality zooming from x4 to x32
Throw Ratio: Vikuiti Super Close Projection Engine
Lamp Power: 230W
Lamp Life: 2000 hours (avg) at 230W
System Specifications
Video Compatibility: NTSC, PAL, SECAM, SDTV, EDTV, HDTV, HDCP, S-Video, 
Component, Composite
PC Compatibility: VGA/SVGA/XGA/SXGA/MAC
Electrical Keystone Correction: Horizontal: +/- 30 degree; 
Vertical: +/- 40 degree
Cooling System: 4 fans with temperature control circuits
Noise Level: Low sytem acoustic noise level
Operating Temperature: 10°C to 35°C
Storage Temperature: -30°C to 65°C
Power Supply: 100-240V; 50Hz/60Hz
Safety Regulatory Approvals: UL, cUL, TUV, CB, Japan-S-mark, Mexico NOM
EMC Regulation: FCC Class B, CE Class B, CCC for China
Environmental Regulations: RoHS and WEEE compliant
Power Consumption: 288W Max
Sound System
Built-in Dolby 2.0 Sound (700) / (2) 2.5W speakers
Built-in Dolby 5.1 Sound (710) / (3) 2.5W, (2) 1.5W and (1) 5W subwoofer
USB Reader
Flash Drive Compatible USB Media Reader for .jpg presentations
DVD Player
Built-in digital DVD player (710 only) 
						

							34
3M™ Digital Media System 700 Series
© 3M 2007. All Rights Reserved.
ENGLISH
Specifications
Other Features
• Front access input/output interface
• Easy-to-read and operate control buttons and remote control
• Adjustable feet for various platforms
• Auto image synchronization
• Automatically saves user adjustments
• On-screen menu in 9 languages
• Kensington Security Slot
• Two IR receiver windows (front and rear)
Dimensions
13.5" (W) x 12.7" (D) x 6.1" (H)
343.5mm (W) x 321.6mm (D) x 155.3mm (H)
Weight
700: 9.9 lbs or 4.5kg
710: 10.6 lbs or 4.8kg
ENGLISH 
						

							35 3M
™ Digital Media System 700 Series
© 3M 2007. All Rights Reserved.
ENGLISH
Other Care
Caring For The Inside Of The Projector 
In order to ensure the safe use of your projector, please have it cleaned and inspected by your local dealer about 
once every 2 years. Never try to care for the inside of the unit yourself. Doing so is dangerous.
Caring For The Lens 
1. Turn off the projector, and unplug the power cord.
2. Lightly wipe the lens with a commercially available lens-cleaning wipe. Do not touch the lens directly with 
your hand.
Caring For The Cabinet And Remote Control 
1. Turn off the projector, and unplug the power cord.
2. Wipe lightly with gauze or a soft cloth.
If soiling is severe, dip soft cloth in water or a neutral cleaner diluted in water, and wipe lightly after wringing 
well. Then, wipe lightly with a soft, dry cloth.
Other Care 
						

							Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on in-
formation believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this 
product, you must evaluate it and determine if it is suitable for your intended application. You assume all 
risks and liability associated with such use. Any statements related to the product which are not con-
tained in 3M’s current publications, or any contrary statements contained on your purchase order shall 
have no force or effect unless expressly set forth in a written agreement signed by an authorized officer 
of 3M.
Technical Support Contact:
3M Austin Center 3M Canada 3M Mexico, S.a. de C.V. 3M Europe
Building A145-5N-01 P.O. box 5757 Apartado Postal 14-139 Boulevard de l'Oise
6801 River Place Blvd. London, Ontario Mexico, D.F.  07000 95006 Cerge Pontoise Cedex
Austin, TX 78726-9000 N6A 4TI Mexico FrancePrinted on 50% recycled 
wastepaper, including 10%
Post-consumer
Litho in USA
@3M 2007
78-6970-9469-2 Rev. B
ENGLISHENGLISH