3D Perception CompactView X10 User Manual

7.2.6 Show accumulated lamp time 
 
In this window you can see the 
accumulated time that the lamp have 
been used. You also use this window to 
reset the accumulated lamp time when 
you have changed lamp. 
 
 
7.3 Control panel menu 
 
In the control panel you have access to 
menus for adjusting picture and audio 
settings. 
 
The icons ”Picture positioning” and 
”Synchronisation Adjustments” are 
only visible if PC source is active. 
 
 
7.3.1 Picture control 
  
 
Select the picture control menu for...

 
  
When PC is selected as source and auto 
contrast is marked, only brightness will 
be available. 
When PC is selected as source, only 
brightness and contrast will be available. 
  
(Optional) When PAL/SECAM video is 
selected brightness, contrast and 
saturation will be available. 
(Optional) All options will be available for 
NTSC video. Select OK to save your 
changes and exit, or select Cancel to exit 
without saving your changes. Selecting 
Default restores factory settings. 
  
 22
  

7.3.2 Picture positioning 
 
Adjust vertical and horizontal position of 
the picture on the screen with the two 
sliders. 
 
Select OK to save your changes and exit, 
or select Cancel to exit without saving 
your changes. 
 
 
7.3.3 Audio control  
Not applicable.  
 
 
 
. 
 
 
 
 
  
 23
  

7.3.4 Synchronisation adjustments 
 
 
It is possible to adjust the synchronisation in 
Computer mode by adjusting the Phase and 
the Frequency. The synchronisation will be set 
by the automatic set-up function. Manual sync 
adjustments should typically not be required. 
 
 
7.3.5 Colour manager 
 
 
The colour manager is designed to give you 
maximum performance from your projector, 
independent of ambient light conditions. In the 
colour manager menu you can choose 
between four pre-defined Colour...

8 MAINTENANCE 
 
All maintenance should be done by 3D Perception authorised service personnel. Contact 
your 3D Perception Value Added Reseller for maintenance. 
 
The 3D Perception projector lamp is designed to give you 2000 hours perf\
ormance. In the 
unlikely event that you should have to change the lamp, you will find co\
mplete instruction on 
how to replace the lamp included in the spare lamp kit. 
 
  
 25
  

9 WHAT TO DO IF (TROUBLE SHOOTING) 
NOTE: The following are some of the typical problems encountered by users of\
 the 
CompactView X10. If you have detected a problem not listed here, or if after trying t\
he 
suggested remedies the problem still exists, you should contact your Value Added Reseller 
immediately. 
 

10 TECHNICAL SPECIFICATIONS 
 
Resolution: 1024 x 768 
  
Colour resolution: 24 bits (30 bits internal processing) 
  
Response time: 16 ms 
  
Processing Latency: 50 us – 12 ms (geometry dependent) 
  
Projection Lamp: 150W UHP 
Lamp life: 2000 Hours typical 
Brightness: 1000 ANSI Lumens 
Contrast Ratio: 500: 1 (ANSI Full on/off typical) 
  
Projection Lens: Carl Zeiss Zoom Lens 
  
Vertical Frequency: 48Hz – 100Hz 
  
Horizontal Frequency: 15KHz – 80KHZ 
  
Dimensions: 13.2 ins (W) x 8.86 ins (D) x...

Image Width v Throw Distance Chart 
The following diagram illustrates the relationship between image width a\
nd throw distance for a 
flat screen. 
 
 
 
  
 29
  

11  LIMITED WARRANTY, ‘FCC STATEMENT’ AND 
‘TRADEMARKS COPYRIGHT’ 
Limited Warranty 
Except as otherwise stated herein, 3D Perception warrants to the first end-user (‘Customer’) 
who purchases a 3D Perception projector from a Value Added Reseller that the 3D Perception 
projector is free from defects in parts and labour under normal use during the warranty period. 
The warranty period means the 12-month period from the date of the Customer’s purchase of 
the 3D Perception projector from a Value Added...