3D Perception CompactView Sx15 E User Manual

							3D Perception        COMPACTVIEW CLAN 
Revision 3          User Manual 
 
 
 6
 
 
6. KEYPAD 
POWER  
Switch the projector on and off. 
 
AUTO 
Automatically detect and synchronize to the signal source selected. 
 
MENU 
Activate the menu system. Use the four arrow keys and Enter to navigate and to activate. 
 
SELECT/KEYSTONE 
Select menu option when the menu system is activated. When the menu system is not in use 
the menu button will activate the keystone correction. Use the four arrow keys to adjust 
horizontally and vertically. 
 
VOLUME +/- 
Use these two arrow keys to adjust the volume when the keystone correction and the menu 
system are not activated. 
 
SOURCE 
Use these two arrow keys to select the source when the keystone correction and the menu 
system are not activated. 
 
STATUS 
This is not a key. The LED indicates the current projector status. See chapter Status for details. 
 
 
  
						

							3D Perception        COMPACTVIEW CLAN 
Revision 3          User Manual 
 
 
 7
 
 
7. STATUS 
GREEN LIGHT 
A permanent GREEN light indicates the 
projector is turned on
 
  
 
YELLOW LIGHT 
A permanent YELLOW light indicates the 
projector is either switched off or is in stand-by 
mode.
 
 
 
YELLOW LIGHT FLASHING  
A flashing yellow light indicates wait. The 
yellow light will flash for a period of 10 -15 
seconds after the power cord is connected and 
for a period of 45 seconds after the projector 
has been turned off. 
 
 
 
RED LIGHT 
A permanent RED light indicates it is time to 
change the projection lamp. Failure to change 
the lamp may lead to the lamp exploding.
 
 
 
RED LIGHT FLASHING  
A flashing RED light indicates the projector is 
overheated. Turn the projector off immediately. 
Check if any air inlets are covered or if the 
ambient temperature is outside specifications. 
Do not remove the power cord. 
 
  
						

							3D Perception        COMPACTVIEW CLAN 
Revision 3          User Manual 
 
 
 8
 
 
8. REMOTE CONTROL 
 
A. POWER  
Switch the projector on and off. 
 
B. AUTO 
Synchronize to the source selected. 
 
C. VOLUME -/+ 
Use these two keys to adjust the volume.  
 
D. LASER 
Activates the laser beam pointer. Do not stare into the laser beam or point it at people!  
 
E. L-SELECT 
The left mouse key. Also used to select option when in the menu system. 
 
F. R 
The right mouse key. 
 
G. PAD 
Used for various functions such as mouse control, keystone correction and menu navigation. 
 
H. VIDEO/ DATA 
Use these two keys to select source. 
 
I. MENU 
Activates the menu system. Use the PAD (G) to navigate and SELECT (E) to activate. 
 
J. KEYSTONE 
Activates the keystone correction. Use the PAD (G) to adjust horizontally and vertically. 
 
K. * 
Not in use 
 
L. MUTE 
Deactivates sound. 
  
						

							3D Perception        COMPACTVIEW CLAN 
Revision 3          User Manual 
 
 
 9
 
 
9. CONNECTOR PANEL 
 
 
A. Component video In G. RS 232 control (E version only) 
B. Super video In H. Audio line In (x 4) 
C. Composite video In I. Audio Out 
D. DVI - Digital RGB J. USB interface 
E. VGA - Analogue RGB In (x 2) K. Mains power connector 
F. VGA - Analogue RGB Out L IR Receiver rear 
  
						

							3D Perception        COMPACTVIEW CLAN 
Revision 3          User Manual 
 
 
 10
 
 
10. SET-UP  
Before any set-up, switch off all equipment. 
 
10.1 Set-up computer 
The projector may be connected to up to three computer sources simultaneously, using the 
VGA 1, VGA 2 and DVI inputs. 
 
A VGA monitor may be attached to the MONITOR VGA output (for VGA 1 and VGA 2 inputs 
only, will not work for DVI or other video inputs). 
 
Sound may be connected for up to two computer sources simultaneously, one for VGA 1 
(AUDIO 1), the other for VGA 2 or DVI (AUDIO 2). 
 
Audio output for an external sound system is available through AUDIO OUT. Connecting to 
AUDIO OUT will automatically deactivate the internal loudspeakers. 
 
Connect the USB cable to allow for remote mouse control. 
 
Connect the power cord. 
 
 
  
						

							3D Perception        COMPACTVIEW CLAN 
Revision 3          User Manual 
 
 
 11
 
 
10.2 Set-up Video 
Before set-up, switch off all equipment. 
 
Three video sources may be connected, using the R/Pr, G/Y, B/Pb (component), S (super 
video) and C (composite video) inputs. 
 
Sound may be connected for up to two video sources simultaneously, one for super or 
composite video (AUDIO 3), the other for component video (VIDEO 4). 
 
Audio output for an external sound system is available at the AUDIO OUT connector. When 
connecting to an external audio system, the internal loudspeakers are automatically 
deactivated. 
 
Connect the power cord. The LED will flash several times before the projector can be switched 
On. 
 
  
						

							3D Perception        COMPACTVIEW CLAN 
Revision 3          User Manual 
 
 
 12
 
 
11. GCM - GEOMETRY CORRECTION MODULE 
Connect the Control PC (running CompactDesigner or CompactControl) to the projectors  
‘Control chain In’ port.  The supplied 6 lead cable plugs into the Control PC’s serial port using a 
RJ12 6 pin to serial DB-9 female adapter. 
 
 
11.1 Connecting multiple projectors 
Multiple projectors may be connected together in a ‘daisy chain’ by using the input and output 
ports on each projector. From the first projector, another 6 lead cable connects between the 
‘Control Chain Out’ port and the ‘Control Chain In’ port of the second projector.  This chain can 
be extended up to the theoretical limit of 255 projectors in a single chain. 
 
 
 
  
						

							3D Perception        COMPACTVIEW CLAN 
Revision 3          User Manual 
 
 
 13
 
 
12. FOCUS AND ZOOM 
12.1 Focus 
Turn the Focus ring (A) on the projection lens 
to get a correctly focused image.  
 
 
12.2 Zoom 
Turn the Zoom ring (B) on the projection lens 
to zoom In and Out. (This is only available on 
the optional intermittent and long throw lens.) 
 
 If the desired image size cannot be achieved 
by adjusting the zoom ring, relocate the 
projector nearer or farther away from the 
projection screen and re-try. 
 
  
						

							3D Perception        COMPACTVIEW CLAN 
Revision 3          User Manual 
 
 
 14
 
 
13. MOUNTING THE PROJECTOR 
13.1 To a Ceiling Mount 
The projector can be ceiling mounted using any approved UL tested/listed ceiling mount fixture 
with a minimum weight capacity of 12 kg (26 lbs). 
 
The ceiling mount obtainable through 3D Perception (as illustrated below) is only approved for 
C
OMPACTVIEW CLAN projectors. 
 
For the ceiling mount use M4 screw. 
 
For proper ventilation, the minimum distance from the ceiling/rear wall should be 30 - 50 cm, (12 
- 20 inches). 
 
The specifications and functionality of the product may change without prior notice. 
 
 
 
A  Locking screw for vertical adjustment  D  Housing f or slide 
B  Locking nut for horizontal adjustment  E  Night aperture 
C  Slide  F  Adjustable flanges*  
 
* Adjustable Flanges are not provided with the ceiling mount, they have to be manufactured by 
individual users to their particular required shapes   
						

							3D Perception        COMPACTVIEW CLAN 
Revision 3          User Manual 
 
 
 15
 
 
13.2 To a Tabletop 
The projector may be mounted or sited directly onto a tabletop. 
 
To adjust the projected image to the desired 
height on the screen, eject the front foot (C) by 
pressing the release button (D), and adjust the 
angle to the right position. 
 
To get an image level with the screen, turn the 
rear feet (E) to the right position.