(Type -S
shown)
Makes lead bullets with a shoulder
between nose and shank in the
wadcutter or semi-wadcutter style.
For paper patched, gas-check, Base
Guard, or dip-lubed bullets made in
one or two strokes of the press. Die
screws into the ram; external punch
fits Corbin FPH-1 floating punch
holder in press head. The internal
punch head length (-H) or tail section
on internal punch (-M, -S) controls the
max/min weight range for a given
die. Bleed holes must not be
covered by either punch.
Lead...
(Type -S
shown)
Makes lead bullets with a shoulder
between nose and shank in the
wadcutter or semi-wadcutter style.
For paper patched, gas-check, Base
Guard, or dip-lubed bullets made in
one or two strokes of the press. Die
screws into the ram; external punch
fits Corbin FPH-1 floating punch
holder in press head. The internal
punch head length (-H) or tail section
on internal punch (-M, -S) controls the
max/min weight range for a given
die. Bleed holes must not be
covered by either punch.
Lead...
LED-1
Lead Extruder Die
for use in Corbin Hydro-press
The Corbin LED-1 Lead Extruder Die is used in the Corbin CHP-1 Hydro-
press or the Corbin CSP-2H Hydraulic Mega-Mite press, to produce lead
wire from soft lead.
The kit consists of a billet moulding set (two billet mould tubes approxi-
mately 4 inches long with a 0.785-inch bore and a mounting base, which
supports a tube while it is being filled with hot lead), and the extruder itself,
which consists of a die body with 0.825 inch bore, a threaded...
LED-1
Lead Extruder Die
for use in Corbin Hydro-press
The Corbin LED-1 Lead Extruder Die is used in the Corbin CHP-1 Hydro-
press or the Corbin CSP-2H Hydraulic Mega-Mite press, to produce lead
wire from soft lead.
The kit consists of a billet moulding set (two billet mould tubes approxi-
mately 4 inches long with a 0.785-inch bore and a mounting base, which
supports a tube while it is being filled with hot lead), and the extruder itself,
which consists of a die body with 0.825 inch bore, a threaded...
How to Swage Bullets Using The LTFB-4-H Die Set
1 2
3
4
6
57Type -H dies fit into the ram of the Corbin Mega-Mite manual (CSP-2), the Hydro, Jr. (CSP-2H) press,
and the Corbin Hydro-Press (CHP-1). The 4-die set consists of a CORE SWAGE (CSW--1-H), a CORE
SEAT(CS-1-H), a POINT FORM (PF-1-H) die, and a LEAD TIP (LT-1-H) die, each with one internal and
one external punch.
The external punch (1) is held in the floating punch holder (2), which comes with the press. A threaded
bushing (3) is removed from the...
How to Swage Bullets Using The LTFB-4-H Die Set
1 2
3
4
6
57Type -H dies fit into the ram of the Corbin Mega-Mite manual (CSP-2), the Hydro, Jr. (CSP-2H) press,
and the Corbin Hydro-Press (CHP-1). The 4-die set consists of a CORE SWAGE (CSW--1-H), a CORE
SEAT(CS-1-H), a POINT FORM (PF-1-H) die, and a LEAD TIP (LT-1-H) die, each with one internal and
one external punch.
The external punch (1) is held in the floating punch holder (2), which comes with the press. A threaded
bushing (3) is removed from the...
How to Swage Bullets Using The
LTFB-4-S or -M Die Set
Type -S dies are 1-inch in diameter, with a 5/8-24 shank, and fit into the ram of the Corbin
CSP-1 All-Steel press. The type -M dies are 3/4-inch in diameter, with a 5/8-24 shank, and fit
into the ram of the CSP-1 or the CSP-3 Silver Press (horizontal). The 4-die set consists of a
CORE SWAGE (CSW-1), a CORE SEAT(CS-1), a POINT FORM (PF-1) die, and a LEAD TIP
(LT-1) die, each with one internal and one external punch.
The external punch is held in...
How to Swage Bullets Using The
LTFB-4-S or -M Die Set
Type -S dies are 1-inch in diameter, with a 5/8-24 shank, and fit into the ram of the Corbin
CSP-1 All-Steel press. The type -M dies are 3/4-inch in diameter, with a 5/8-24 shank, and fit
into the ram of the CSP-1 or the CSP-3 Silver Press (horizontal). The 4-die set consists of a
CORE SWAGE (CSW-1), a CORE SEAT(CS-1), a POINT FORM (PF-1) die, and a LEAD TIP
(LT-1) die, each with one internal and one external punch.
The external punch is held in...
PCM-1
Power Cannelure
Machine
Cannelure 100 bullets/minute
Weight: aprox. 70-lbs.
Power: 110-120 volts 60 Hz.
Motor: 1/4-HP Gear drive.
Forced air cooling: 100 CFM.
Rust resistant, baked-in powder-
coated grey finish on both the
steel frame and the heavy gauge
steel cover.
Built-in 5-amp circuit breaker and
switch with bright pilot lamp, for se-
cure continuous heavy duty operation in
a production line or on the bullet-maker’s
bench.
Massive thrust bearing adsorbs the powerful forces that roll precision...
PCM-1
Power Cannelure
Machine
Cannelure 100 bullets/minute
Weight: aprox. 70-lbs.
Power: 110-120 volts 60 Hz.
Motor: 1/4-HP Gear drive.
Forced air cooling: 100 CFM.
Rust resistant, baked-in powder-
coated grey finish on both the
steel frame and the heavy gauge
steel cover.
Built-in 5-amp circuit breaker and
switch with bright pilot lamp, for se-
cure continuous heavy duty operation in
a production line or on the bullet-maker’s
bench.
Massive thrust bearing adsorbs the powerful forces that roll precision...
Corbin Pound Die PD-1
The Corbin Pound Die makes swaged lead bullets without a press, using a 5 pound plastic, leather, or lead faced
mallet to supply the driving force. The die consists of five parts:
1. Base
This is the largest diameter cylinder. It is machined so
that the die and base punch both fit into its cavity. One end of
the die body is machined to mate with the largest diameter hole
in the base. The base holds the die and base punch during
swaging, and then the base punch is removed and the...
PT-50-H
PO Box 2659, White City, OR 97503 USA
Phone 541-826-5211 Fa x 541-826-8669 E-Mail [email protected]
Web Site http://www.corbins.com
Priming Tool for the 50 BMG
Use the precision of your Corbin Swage
Press to seat primers in the .50 BMG and
similar cases.
Seating Punch:
presses against
anvil screw to
seat primer.
Shell holder body: screws into
1.5X12 TPI press head.
Shell
holder
INSTRUCTIONS:
The PT-50-H fits the ram and press head of Corbin’s CSP-2 Mega-
Mite press, CSP-2H...
How to Swage Bullets Using TheRBTO-4-M, -S, or -H Die Set
Type -H dies fit into the ram of the Corbin Mega-Mite press (CSP-2), Corbin
Hydro, Jr., (CSP-2H) press, and the Corbin Hydro-Press (CHP-1). The type -
M dies fit either the horizontal Silver Press (CSP-3) or the vertical Series II
Press (CSP-1). The type -S dies fit only the Series II Press (CSP-1). The last
letter, -M, -S, or -H, describes the outside diameter, threads, punch lengths,
and which presses the die set will fit. If a tool fits both...
How to Swage Bullets Using The
RBTL-5-M, -S, or -H Die Set
Type -H dies fit into the ram of the Corbin Mega-Mite press (CSP-2), Corbin
Hydro, Jr., (CSP-2H) press, and the Corbin Hydro-Press (CHP-1). The type -M
dies fit either the horizontal Silver Press (CSP-3) or the vertical Series II Press
(CSP-1). The type -S dies fit only the Series II Press (CSP-1). The last letter, -
M, -S, or -H, describes the outside diameter, threads, punch lengths, and which
presses the die set will fit. If a tool fits both...
1234567890123456789012345678901212345678901234567890123456789012123456789012345678901
1234567890123456789012345678901212345678901234567890123456789012123456789012345678901
1234567890123456789012345678901212345678901234567890123456789012123456789012345678901
1234567890123456789012345678901212345678901234567890123456789012123456789012345678901
oRFJM-22R 22LR to 224 caliber (5.56mm)
for use in a reloading press...
oRFJM-22M22LR to 224 caliber (5.56mm)
for use in Corbin Swage presses
oRFJM-6MR22LR to 243...
Jacket Serrate/Draw Die
SDD-1 -R -M -S -H Caliber: _____________
The Corbin SDD-1 Serrate/Draw Die may be used to score the outside
of an empty bullet jacket, so the bullet will separate along the score
lines on impact. For effective high frangibility projectiles, the empty
jacket is pushed base first through the die with a punch that fits inside the
jacket. This scores the length of the jacket. The core is then seated and
the ogive is formed, further stressing the score lines in the nose area...
