Vodavi Starplus Dhs/dhs-e Technical Manual

4-50DSS Console 
To erase the contents of a programmable feature button:
1. Press [FEAT ]
2. Dial [#] + [5]
3. Press the Programmable Feature Button.
4. Dial [0]
5. Press [HOLD]
Executive Telephones
To program DSS console buttons:
1. Press [FEAT ]
2. Dial [#] + [5]. The display shows:
3. Press a programmable feature button. The current contents of that button is 
displayed. 
4. Press [show]. The name of the current feature stored is displayed.
5. Press [chg]. The display shows the following (DHS): 
Or on...

DSS Console 4-51
To program a BLF/DSS button:
1. On the DHS, press [STA], then chg.
2. Dial the Station number.
3. Press [save]
OR
1. On the DHS-E, Press [DIR]. The display shows:
2. Dial the station number.
3. Press [save]
To program a system feature:
1. On the DHS, press soft key [feat], then [chg].
2. Dial the Feature code number.
3. Press [save]
OR
1. On the DHS-E, press soft key [feat]. The display shows:
2. Press [FEAT ]. F will appear on the display:
3. Dial the feature code.
4. Press [save]
To...

4-52Emergency Numbers
†Any feature button programmed with a code previously assigned to a different 
feature button will cause the previously programmed feature button to become 
unassigned.
†Programmable feature buttons cannot be programmed for CO line group operation 
when the system is configured for KEY system operation.
Emergency Numbers
Description
The DHS/DHS-E System Speed Dial feature provides use of emergency number calling 
at stations that may be otherwise restricted from dialing. All 80...

External Call Forward (ECF)4-53
External Call Forward (ECF)
Description
Assuming that one line has been programmed as the ECF Incoming CO line and another 
line has been programmed as the ECF Outgoing CO line and System Speed Dial bin 99 
contains a telephone number where calls will be forwarded:
Operation
When the ECF Incoming CO line is ringing, the system:
†Answers the incoming call.
†Seizes the outgoing CO line.
†Dials the telephone number stored in System Speed bin 99.
†Makes a CO line-to-CO line...

4-54Fe ature Bu tton  In quir y
3. At an Executive Telephone, the display returns to the CO line connected display 
following the flash time-out or 10 seconds later.
Conditions
†The Flash code may be stored in any speed dial bin.
†The Flash code may be stored in the Last Number Redial buffer. When you activate 
redial, an Executive Telephone display will show a / (forward slash) to indicate the 
Flash code. 
†The Flash time is programmable from 100ms to 1500ms in increments of 100ms (1/
10th of a...

Feature Button Programming4-55
Feature Button Programming
Description
Depending upon the telephone model, 8 or 20 programmable feature buttons are 
available. The Basic model has eight dual-colored feature buttons for CO line, station, or 
feature access code assignments. The Enhanced and Executive models have 20 dual-
colored programmable feature buttons.
All system feature codes may be stored on the programmable feature buttons for one-
button operation. Certain programmed feature buttons will light...

4-56Feature Button Programming
To program a CO button: (DHS-E only)
1. Dial [1] + line number.
2. Press [HOLD]
To erase the contents of a programmable feature button:
1. Press [FEAT ]
2. Dial [#] + [3]
3. Press the Programmable Feature Button.
4. Dial [0]
5. Press [HOLD]
Executive Key Telephones
To program a feature button:
1. Press [FEAT ]
2. Dial [#] + [3]. The display shows:
Table 4-6: CO Line Feature Button Codes
DHS DHS-E
00 =Any Group 02 = CO Line Grp 2 200 = CO Line Grp 1 202 = CO Line Grp 3
01 =...

Feature Button Programming4-57
3. Press a programmable feature button. The current contents of that button is 
displayed. For this example, let’s use button 20.
    The following sequence of steps applies to DHS-E only:
    
1. Press [show]. The name of the current feature stored is displayed.
2. Press [chg]. The display shows the following:
Three feature button categories are available for feature button programming: CO lines 
(co Ln), Station (sta), and Feature (feat).
To program a CO line button: 
1....

4-58Flexible Line Assignment
To program a system feature:
1. Press [FEAT ]. The display shows:
2. Press [FEAT ].  F will appear on the display:
3. Dial the feature code.
4. Press [save]
To erase the contents of a programmable feature button:
1. Press [save] instead of dialing a code.
Conditions
†In some cases, a user may program a feature button for a specific CO line although 
access is restricted to that line via system programming. In this situation, the 
telephone is still governed by system...

Flexible Receive Assignment4-59
Flexible Receive Assignment
Description
Stations may be allowed to answer or retrieve from hold, specific CO lines assigned in 
system programming. Receive assignments should be assigned to any stations that need 
to answer incoming calls. A station does not have to hear ringing or be programmed with 
Flexible Ring Assignment in order to answer an incoming CO line. Also, Call Pickup can be 
used to answer the oldest incoming CO calls. During System Night Service operation,...