ViewSonic Pjd6553w Projector User Manual

56
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically  calculated by the built-in timer. 
To obtain the lamp hour information: 
1. Press  MENU/EXIT on the projector or Menu on the remote control and then press  
/  until the  SYSTEM SETUP: Advanced menu is highlighted. 
2. Press  to highlight  Lamp Settings and press MODE/ENTER on the projector or  
ENTER  on the remote control. The Lamp Settings page is displayed. 
3....

57
Timing of replacing the lamp
When the Lamp indicator lights up red or a message appears suggesting it is time to  replace the lamp, please install a new lamp or  consult your dealer. An old lamp may cause a  malfunction in the projector and in some instances the lamp may explode.
CAUTION 
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too  hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator  still lights up after...

58
Replacing the lamp
To prepare a new lamp, contact your dealer and tell the lamp type number. 
Type number: RLC-070 (PJD5126/PJD6223) 
Type number: RLC-071 (PJD6253/PJD6553w)
WARNING
Hg - Lamp contains mercury. Manage  in accordance with local disposal  
laws. See www.lamprecycle.org
• To reduce the risk of electrical shock, always turn the projector off and disconnect the  power cord before changing the lamp. 
• To reduce the risk of severe burns, allow the pr ojector to cool for at least 45 minutes...

59
5. Loosen the screw that secures the lamp. 
6. Lift the handle so that it stands up. Use  
the handle to slowly pull the lamp out 
of the projector.
CAUTION 
• Pulling it too quickly may cause the lamp  to break and scatter broken glass in the  projector. 
• Do not place the lamp in locations where  water might splash on it, children can reach it, or near flammable materials. 
• Do not insert your hands into the projector  after the lamp is removed. If you touch the  optical components inside, it...

60
13. Restart the projector.
CAUTION 
Do not turn the power on wi th the lamp cover removed.
Resetting the lamp timer
14. After the startup logo, open the On-Screen  
Display (OSD) menu.
15. Go to the  SYSTEM SETUP: Advanced >  
Lamp Settings  menu. Press MODE/ENTER  
on the projector or  ENTER on the remote  
control. The  Lamp Settings page is  
displayed.  
16. Press  to highlight  Reset lamp timer and  
press  MODE/ENTER on the projector or  
ENTER  on the remote control. A warning  
message is...

61
Indicators
LightStatus & Description
PowerTe m pLamp
Power events
Blue Flashing Off OffStand-by mode
Blue Off OffPowering up
Blue Off OffNormal operation
Lamp events
Purple Flashing Off RedThe projector has shut down automatically. If you try to re- start the projector, it will  shut down again. Please contact  your dealer for assistance.
Off Off Red1. The projector needs 90  seconds to cool down. Or 
2. Please contact your dealer for assistance.
Thermal events
Off Red Off
The projector has shut down...

62
Troubleshooting
The projector does not turn on. 
No picture 
Blurred image 
Remote control does not work
CauseRemedy
There is no power from the power  
cord. 
Plug the power cord into the AC inlet on the  projector, and plug the power cord into the  
power outlet. If the power outlet has a switch, 
make sure that it is switched on. 
Attempting to turn the projector on  again during the cooling process. Wait until the cool ing down process has  completed.
CauseRemedy
The video source is not turned on...

63
Specifications
Projector specifications
All specifications are subject to change without notice.
General
Product name DLP Projector 
Model name PJD5126 PJD6223 PJD6253 PJD6553w
Optical
Resolution 800  x 600 SVGA 1024 x 768 XGA 1280 x 800 WXGA 
Display system 1-CHIP DMD 
Lamp 180 W lamp 240 W lamp
Electrical
Power supply AC100–240V, 2.9 A, 50/60 Hz  (Automatic) AC100–240V, 3.5 A, 50/60 Hz  (Automatic) 
Power  consumption 287 W (Max); < 1 W (Standby) 361 W (Max); < 1 W (Standby)
Mechanical
Weight 2.6 Kg...

64 
  
Environmental Requirements
Product name DLP Projector 
Model name PJD5126 PJD6223 PJD6253 PJD6553w 
Operating  temperature 0°C–40°C at sea level 
Operating relative  humidity 10%–90% (without condensation) 
Operating altitude • 0–1499 m at 0°C–35°C 
• 1500–3000 m at 0°C–30°C (with  High Altitude Mode on) 

65
Dimensions
293.94 mm (W) x 84 mm (H) x 242 mm (D)
Ceiling mount installation
ZOOM
TEMPLMMPMODEENTERAUTOSOURCEMENUEXIT
293.94242
84
160
137
11 580
Ceiling mount screws: 
M4 x 8 (Max. L = 8 mm)
Unit: mm