Toshiba Projector Tdp D2 User Manual

							21
Operations
20
1
Turn on the power.Turn on the power, following the instructions in “Turning on the power” 
p.19
.
2
 Select language (When using for first time).When the projector is used for the first time after purchase, a message is displayed on
the screen, and the language menu appears. The default language is English.
(If the screen focus is not on the menu, adjust according to step 
6.)
qUse the 
 
 buttons to select the desired
language, and press the 
 button.
A message displays the selected language.
wPress the 
 button to erase the message.
Notes•After the first time the projector is turned on, the Language menu does not appear
upon startup. However, from the Reset menu 
p.29
 select “Reset all” to display the
Language menu the next time the projector is turned on.
•The language can also be set via the Display setting menu 
p.29
.
•This owner’s manual assumes that English has been selected.
3
Place connected device(s) in operating status.Turn on and boot up connected computers and other devices.
Select “Cancel” or install driver contained in the supplied CD-ROM, when the dialog
box of the Add New Hardware Wizard screen appears on the computer when
connecting a computer. (The supplied CD-ROM contains a driver information file
named TOSHIBA_TDP.inf. Click the Browse button of the dialog box to find and
designate this file.)
4
Select input.qPress the INPUT button.
A list of inputs appears on the screen.
wUse the 
 
 buttons to select the desired
input, and press the 
 button.
The picture for the selected input is projected.
Basic operations
English
Français
Português Deutsch
Italiano
Español
................
..............
..............
................
...............
..........
...................
.......
.......
...................
English
French
German
Italian
Spanish
Portuguese
Japanese
Chinese (simplified)
Chinese (traditional)
Korean
Computer
Y/P
B/PR
Video
S-video
Turning the power on and off (Continued)
Notes•The start-up screen will disappear after a moment. You can dismiss the start-up screen
before this by performing any operation. You can also configure the start-up screen not to
appear via the Display setting menu 
p.29
.
•The first time you use the projector after purchase, after the start-up screen disappears,
the Language menu is displayed 
p.21
.
 Turning the power off1
Press the ON/STANDBY button.A message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
2
Press the ON/STANDBY button again.The screen turns off, but the internal cooling fan continues to operate for a short while.
Then, the projector goes into standby mode.
When cooling lamp During internal cooling After cooling complete
FAN TEMP LAMP ON
FAN TEMP LAMP ON
AFAN TEMP LAMP ON
B
C
(Green) (Green) (Orange)
Flashing(Green) (Off) (Orange)(Off) (Off) (Orange)
A
During cooling, the LAMP indicator flashes. In this state, the power cannot be
turned back on. In addition, unplugging the power cord or turning off the main
power switch in this state will shorten the life of the lamp.
B
After the LAMP indicator goes off, the cooling fan continues to operate for a
short while, in order to expel excess internal heat. If you are in a hurry, there is
no problem with unplugging the power cord or turning off the main power switch
in this state.
C
In standby mode
Note•The projector consumes about 6W of power in standby. We recommend that you unplug
the power cord or turn off the main power switch if you will not be using the projector for
an extended period.PRECAUTIONS•Before unplugging the power cord or turning off the main power switch, make sure that
the LAMP indicator is off. Unplugging the power cord or turning off the main power
switch and cutting off the power while the projector is running or being cooled will
shorten the life of the lamp. However, please unplug the power cord if the projector
locks up or acts abnormally.
•If the power cord is unplugged before cooling is complete, give the lamp time (about 10
minutes) to cool before plugging it back in.  If the lamp overheats it may fail to light, and
its lifetime will be shor tened.
DRAGR-CLICK
L-CLICKRESIZE OFF
INPUTMENU
VOL.+ VOL.-RESIZEINPUT
ON/STANDBY INPUT
MENU ON LAMP TEMP FAN
AUTO KEYSTONE AUTO SETVOL.
+
VOL.-Control panelRemote
Control 
						

							23
Operations
22
Using auto setting (Auto setting)
This function sets up the projector to the optimum state for
each type of the input signal by using simple operations.1
Press the AUTO SET button.The Auto setting menu appears.
2
Press the AUTO SET button again.The menu item is automatically adjusted/set.
For computer input, the 
 icon will appear during
processing.
Note•Auto adjustment/setting may not be performed correctly for input signals other than
those supported by the projector 
p.36
, p.37
.
Manual adjustment and setting
The menu items vary according to the input type, as shown in the table below.
Use the 
 
 
 
 
 buttons to adjust the items in the table below, then press
the 
 button when you are finished. The menu disappears.
DRAGR-CLICK
L-CLICKAUTO
KEYSTONE
AUTO
SET
PAG E
UP PAG E
     DOWNFREEZE
MUTECALLON/STANDBY
LASER
ON/STANDBY INPUT
MENU ON LAMP TEMP FAN
AUTO KEYSTONE AUTO SETVOL.
+
VOL.-
Using handy features
Control panelRemote
Control
PhaseAdjust with           to eliminate flicker.
Frequency
Adjust with            to eliminate periodic patterns and 
flickering when many vertical lines appear in the screen.
H-positionMove left           Move right
V-positionMove up            Move down
PhaseAdjust with           to eliminate flicker. Input Item
Description
Computer
Select Item Select Item
Signal format
[     : Enter to setting mode]    [          : Select one 
of the following]    [Apply:     ]
480i(525i)@60Hz/480p(525p)@60Hz/
 576i(625i)@50Hz/576p(625p)@50Hz/
 720p(750p)@60Hz/720p(750p)@50Hz/
 1080i(1125i)@60Hz/1080i(1125i)@50Hz/
 1035i(1125i)@60Hz/1152i(1250i)@50Hz
Video mode[     : Enter to setting mode]    [          : Select one 
of the following]    [Apply:     ]
 
NTSC/PAL/SECAM/PAL-N/PAL-M/PAL60/NTSC4.43
Y/P
B/PR
Video
S-video
5
Projector placement angle adjustmentsThe placement angle and the height of the projected image can be adjusted by the foot
adjuster.qLift up the front of the projector until
it is at the desired angle, then press
the foot adjuster release button.
The foot adjuster extends. Release the
button to lock the position.
wTurn the foot adjuster to fine-tune
the angle.
eTo adjust the horizontal angle, use
the tilt adjuster.
To stow the foot adjuster, hold up the projector while pressing the foot adjuster
release button, then slowly lower the projector will the button depressed.
6
Adjusting the picture size and focusqUse the zooming lever to adjust the screen
size.
wUse the focusing ring to adjust the focus.
7
Adjusting the volume with the 
 
 buttons
The speaker volume can be adjusted when an audio signal is being input.Notes•Note that the lamp characteristics may rarely cause the brightness to fluctuate slightly.
•A lamp is consumable supplies.
If used for extended periods, images will appear dark, and the lamp could burn out.  This
is characteristic of a lamp, and is not malfunction. (The lifetime of the lamp depends on
conditions of use.)
•The DMD
TM is made using extremely advanced technology, but there may be black spots
(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel.
Please note that these are not malfunctions.
•Although this projector supports a wide range of RGB signals 
p.36
, any resolutions not
supported by this projector (XGA) will be expanded or shrunk, which will affect image
quality slightly. To view high-quality images, it is recommended that the computer’s
external output should be set to XGA (1,024 x 768) resolution.
•With some models of computer having LCD displays or the like, displaying images
simultaneously on the projector and the monitor’s display may prevent the images from
displaying properly. If this happens, turn off the computer’s LCD display. For information
on how to turn off the LCD display, see the owner’s manual of your computer.
•If a signal not supported by the projector is input, the 
 icon will appear.
•If a no signal is being input from the connected device, the 
 icon will appear.
•If an unavailable operation button is pressed, the 
 icon will appear.
3
2
1
1
2
Basic operations (Continued) 
						

							25
Operations
24
Freezing the image (Freeze)
The image being projected can be made to be frozen. This function is to
be used to pause a video during a presentation, etc.
Press the remote control’s FREEZE button.The picture is paused. The Freeze function is released when
pressing the FREEZE button again.Notes•The 
 icon will appear while freeze is in effect.
•The freeze function can be used on the resize function. Other
operations will release the freeze.
•Even if an image is frozen on the projector, it is still changing on the video or other
equipment.
Enlarging the picture size (Resize)
The image being projected can be enlarged.1
Press the remote control’s RESIZE (+)  button.The enlargement ratio is increased each time the RESIZE (+)  button is pressed.
2
To decrease the enlargement ratio, press the remote control’s RESIZE
(-) button.The enlargement ratio is decreased each time the RESIZE (-) button is pressed.
(The image cannot be shrunk to less than its original size.)
3
Press and hold down the 
 
 
 
 buttons to
move the enlarged area.
4
Press the RESIZE OFF button to undo the resize.The resize is released, and the image returns to its original size.Notes•The 
 icon will appear while resize is in effect.
•An enlarged image can be frozen using the FREEZE button. The resize function on
a frozen image can also be used.
•Operations other than freeze will release the resize.
•Since the enlargement is performed using digital processing, enlarging the image
will cause it to appear jagged.
•Rarely, the picture could become garbled while the enlarged area is being moved.
DRAGR-CLICK
L-CLICKAUTO
KEYSTONE
AUTO
SET
PAG E
UP PAG E
     DOWNFREEZE
MUTECALLON/STANDBY
LASER
Remote
Control
DRAGR-CLICK
L-CLICKRESIZE OFF
INPUTMENU
VOL.+ VOL.-RESIZEINPUT
4321
Remote
Control
Correcting the keystone distortion (Keystone)
When the foot adjuster 
p.22
 is used to change the
projection angle, the picture will undergo keystone (trap-
ezoidal) distortion.
This projector is capable of correcting this keystone
distortion.
1
Press the AUTO KEYSTONE button.The Keystone menu appears.
2
Press the AUTO KEYSTONE button again.The keystone distortion is automatically corrected. The 
 icon will appear during
processing.
Manual adjustment
Use the 
 
 buttons for keystone adjustment. When the adjustment is finished,
press the  button. The menu disappears.
Notes•Depending on the amount of keystone adjustment and the contents of images,
some information may be lost, or the picture quality may suffer.
•Keystone adjustment will not change the shape of the menus.
Cutting off the picture and sound temporarily (Mute)
When you want to temporarily project the images of another projector,
overhead projector, etc., this projector’s images and sound can be turned
off.
Press the remote control’s MUTE button.The picture and sound are cut off. The Mute function is released
when pressing the MUTE button again.Notes•The 
 icon will appear while mute is in effect.
•Operating any other function exits the muting.
DRAGR-CLICK
L-CLICKAUTO
KEYSTONE
AUTO
SET
PA G E
UP PA G E
     DOWNFREEZE
MUTECALLON/STANDBY
LASER
ON/STANDBY INPUT
MENU ON LAMP TEMP FAN
AUTO KEYSTONE AUTO SETVOL.
+
VO L.-
DRAGR-CLICK
L-CLICKAUTO
KEYSTONE
AUTO
SET
PAG E
UP PAG E
     DOWNFREEZE
MUTECALLON/STANDBY
LASER
Control panelRemote
Control
Remote
Control
KeystoneShrink screen bottom            Shrink screen top Item Description
Before correction
After correction
Using handy features (Continued) 
						

							27
Operations
26
You can call up on-screen menus, and conduct a number of adjustments and settings,
using the operation buttons 
p.14
 on the control panel (main unit side) and remote control.
How to use the menus
The menu shown below is only for operation instructions and might be different from
the actual display.
Using the menus
Note•Menu adjustments and settings are saved when the power is turned off via the ON/
STANDBY button. If the main power switch is turned off before this, or the power goes
out, then the data will not be saved.
Display the Setting display menu
To  Status display
The menu disappears
1. Start
2. Select a Category
3. Adjustments & Settings
4. Back6. End 5. To  Finish
Finish via the Status 
display menu.
Select a category by using  
         .
There are following three 
categorys.Displays the current 
adjustments of selected 
category.
Item shown with gray 
cannot be adjusted for the 
current input source.
p.28
Image adjustment menu
p.28
Default setting menu
p.26
Display setting menu
p.29
The figure shows a typical example.  
As the display may differ depending 
on the item, use the following pages 
as a reference.
Item
Adjustment/Setting Value
This mark signfy that 
there are options.
Press        to display a 
list of options.
These marks signify the 
items can be adjusted/set 
by using                .
These marks signify an 
item can be switched by 
using                .
These marks signify the items can be selected from 
the list by using            .
After an item selected, apply it by pressing      .
Press      to open the menu 
of the selected category.
Displaying Information [Status display]
This displays information about the input signal, lamp use time, etc.
Press the 
 button twice (or press the CALL button on the remote
control once).
When the 
 button is pressed once, the Setting
display menu appears. Pressing it again displays
information p.27
. The table below shows what kind
of information is displayed. Press the button (or the
CALL button on the remote control) again to
dismiss the display.
“Ye s”: displayed, “No”: not displayed
Item Description
Computer Y/P
B/PR
Video S-video
Input Input source name Yes Yes Yes YesRGB signal mode RGB input mode 
[Note 1]
Ye s N o N o N o
H-resolution Horizontal resolution (in bits) Yes No No NoV-resolution Vertical resolution (in bits) Yes No No NoH-frequency Horizontal sync frequency Yes No No NoV-frequency Vertical sync frequency 
[Note 2]
Ye s N o N o N o
Sync Sync signal polarity 
[Note 3]
Ye s N o N o N o
Signal format Y/P
B/PR signal format No Yes No No
Video mode Color method of video signal No No Yes YesLamp time Time of lamp use 
[Note 4]
YesYesYesYes
Version Firmware version 
[Note 5]
YesYesYesYes
Notes
1: The mode of supported RGB signals 
p.36
 is shown.
2: Same as the refresh rate of the computer signal.
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be
used as a counter of guaranteed lamp time.) When the time displayed approaches 1,500
hours, consult with a store about getting a replacement lamp (for TDP-D1: TDPLD1 and for
TDP-D2: TDPLD2) (sold separately) prepared.
5: [Version] shows the version of the projector’s internal control program. This version is
referred to for customer service, etc.
Notes•The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
•Conducting another operation while information is being displayed dismisses the
display.
Using handy features (Continued)
DRAGR-CLICK
L-CLICKAUTO
KEYSTONE
AUTO
SET
PA G E
UP PA G E
     DOWNFREEZE
MUTECALLON/STANDBY
LASER
ON/STANDBY INPUT
MENU ON LAMP TEMP FAN
AUTO KEYSTONE AUTO SETVOL.
+
VO L.-Control panelRemote
Control 
						

							28
29
Operations
The image adjustment menuUse this menu to adjust image-related items.
Items Items that can be adjusted are marked with  “Ye s”, and those that cannot are marked
with “No”.
Item    
  
Description
Computer
Y/P
B/PR
Video S-video
 
ContrastLower
Higher Yes Yes Yes Yes
BrightnessDarker
Brighter Yes Yes Yes Yes
ColorLighter
Deeper No Yes Yes Yes
Tint 
[Note 1]
Reddish
Greenish No No Yes Yes
SharpnessSofter
Sharper No Yes Yes Yes
R-levelLess red
More red Yes Yes Yes Yes
G-level
Less green
More green
Ye s Ye s Ye s Ye s
B-levelLess blue
More blue
Ye s Ye s Ye s Ye s
Up/down shift 
[Note 2]
Shift down
Shift up No Yes Yes Yes
Notes
1:Tint can only be adjusted when Video mode 
p.23
 is NTSC or NTSC4.43.
2:Up/down shift can only be adjusted when Screen size 
p.29
 is Wide.  During the adjustment, the
picture may be instability.
The default setting menuThis menu shows placement status and other settings.
Set projection mode in accordance with Placement Style  
Set the time to wait after signal input stops until turning off the power: 
Off (not turned off)          1 min           2 min           ...          60 minSet whether to turn on the power when the ON/STANDBY button is pressed 
(Manual), or the main power switch is used (Auto).          Manual             AutoSet the lamp power                                    Standard           LowSet standby mode according to functions used   Standard            Economy
Description
Item
Projection
mode
No signal 
power off
Power on
Lamp power 
[Note 1]
Standby mode 
[Note 2]
(Back hung 
from ceiling) (Placed 
on floor)(Rear)(Hung from 
ceiling)
p.21
Note
1: When lamp power is set to low, the screen becomes a little darker, but the cooling fan noise gets
quieter. This setting will be cleared when you turn the power off.
Notes•Note that if Power on is set to Auto, then if the main power switch is turned on when
power is restored after a power outage, the projector power will come on.
•Even if Power on is set to Auto, press the ON/STANDBY button to turn off the power.
Turning off the main power switch to cut off the power will shorten the life of the lamp.
The display setting menuUse this menu to set screen display-related items.
(Full):  Display with native resolution (1,024 x 768 pixels)
(Thru): Display with sampling resolution (for computer input)
(Wide):  Wide-screen display (for Video, S-video, and Y/P
B/PR)
Select one of the languages below to use for displaying menus and messages[     : Enter setting mode]     [          :Selection]      [Apply:       ]
English/Français/Deutsch/Italiano/Español/
Português/            /                      /                      /Screen to display when there is no input signal                        
 (Logo)                            (Blue)                            (None)
Display icons as function guidesOn Off
Display start-up screen when power turned on On Off Description
Item
Screen size
Language
Background
Icon
Start-up screenNote•If “Thru” is selected for screen size, portions exceeding the native resolution will not
appear on the screen. Note that for RGB signals with clock frequency 140MHz or lower,
all input pixel signals are sampled. (This effect is noticeable when the screen is enlarged
using the Resize function 
p.36
). However, if the clock speed is higher than this, the
RGB pixel signal is thinned before sampling.
Reset menu 
(Special menu)
This menu is displayed when other menus are not displayed, and the 
 button is held
down until the menu appears.
•When the screen is placed vertically, and Auto keystone correction is executed, but
the keystone correction is not successful, stow the foot adjuster in its original position,
place the projector on a flat surface, select Horizontal reference value reset, and press
the 
 button.
•Select Reset All and press the 
 button to return all menu items to the factory settings.
Reset the horizontal reference value for Auto keystone correction[     : Enter execution mode]     [Ye s           No]     [Apply:     ]
Reset all menu items to their factory settings
[     : Enter execution mode]     [Ye s           No]     [Apply:     ] Description Item
Horizontal reference 
value resetReset all
Using the menu (Continued) 
						

							31
Maintenance
30
Lens cleaning•Clean the lens with a commercially available blower and/or
lens cleaner.
•The lens is easily scratched, so do not rub it with hard objects,
or strike it.Main unit cleaning•Clean the main unit after unplugging the power cord.
•Wipe dirt off the main unit gently with a soft cloth.
•If the soiling is severe, dip the cloth in a neutral
detergent diluted in water, wring well, and gently wipe
off the dirt, then finish up by wiping with a dry cloth.Replacing cooling fans
To maintain the performance, it is recommended that cooling fans should be replaced
about every 2 to 3 years. Consult with your dealer for details.
Lamp replacementA lamp is consumable supplies. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The
lifetime of the lamp depends on conditions of use.) If this happens, replace it with a new
one.
 CAUTION
•Request cleaning and maintenance of a ceiling-mounted unit from your projector
dealership.
• When replacing, always use the specified lamp (for TDP-D1: TDPLD1 and it for TDP-
D2: TDPLD2) (sold separately).
• If you have been using the projector, the lamp will be very hot, and may cause burn
injuries.
Wait for the lamp to cool (for longer than 1 hour) before replacing it.
• If the lamp should break, please handle with care to avoid injury due to broken pieces
and contact your dealer for repair service.1
Unplug power cord.
2
Wait until lamp is sufficiently cooled.Wait for at least 1 hour.
Lens and main unit cleaning
A computer can be operated using the projector’s remote control.  This function is available
on any computer with the Windows 98SE, Windows Me, Windows 2000, Windows XP, Mac
OS 9, or Mac OS X, that is equipped with a USB port which can support USB1.1.
However, please note that Toshiba does not the guarantee operation of all computers.1
Connecting a computerConnect the projector to a computer using the supplied USB cable.
S-VIDEO VIDEO AUDIO IN
AUDIO OUT USB
COMPUTER IN MONITOR OUT
CONTROL
2
Operating a computerMoving the mouse pointer
Move the pointer control button in the direction that you wish the mouse pointer to
move, then press.
To left click
Press the L-CLICK button.
To right click
Press the R-CLICK button.
To drag and drop
Press the DRAG button on the object.  Next, move the object to the position where
you wish by using the pointer control button then press the DRAG button again.
Changing page of file
Use the PAGE UP and PAGE DOWN buttons to switch PowerPoint
® slides, etc.
DRAG
R-CLICK
L-CLICKAUTO
KEYSTONE
AUTO
SET
PAG E
UP PAG E
     DOWNFREEZE
MUTECALLON/STANDBY
LASER
RESIZE
INPUT
Operating a computer using the remote control
To USB port Computer
USB cable
(supplied)
Pointer control
R-CLICK
L-CLICKPAGE UP
PAGE DOWN
DRAG 
						

							33
Others
32
The indicator lights inform you of internal abnormalities.
No power⇒Problem with projector
•Unplug the power cord, and contact your dealer.
⇒The lamp cover is not properly attached.
•Unplug the power cord, and reattach the lamp cover. 
p.32
Lamp went out during use, or won’t come on⇒The abnormal indication of the LED continues for about 1 minute
then the projector returns to standby mode after cooling for a
while.  If the projector fails to operate normally after turning the
power back on, either the lamp needs replacing, or there is a
problem with the projector.
•If a lamp burns out, replace it with a new one.
•Unplug the power cord, and contact your dealer.Power went out during use, or power won’t come on⇒Internal overheating, or the outside temperature is too high.
•Place the projector so that the air intake and exhaust are not
blocked.
•Unplug the power cord and wait for a short while, then turn the
power back on.
•Clean the air filter. 
p.30
❈The 
 icon will appear before the power goes out.
❈The abnormal indication of the LED continues for about 1
minute then the projector returns to standby mode after cooling
for a while.
Power went out during use, or power won’t come on⇒Problem with internal cooling fan.
•Unplug the power cord, and contact your dealer.
❈The 
 icon will appear before the power goes out.
❈The abnormal indication of the LED continues for about 1
minute then the projector returns to standby mode after cooling
for a while.
PRECAUTIONS•Make sure to unplug the power cord if something goes wrong.
•If the power cord is unplugged before cooling is complete, give the lamp time (about 10
minutes) to cool before plugging it back in. If the lamp overheats it may fail to light.
Unplugging the power cord repeatedly when the temperature is high will shorten the life
of the lamp. (Even if you are not concerned about lamp lifetime, the light may not come
on if you do not wait at least 3 minutes.)Trouble indications
FA N TEMP LAMP
ONFA N TEMP LAMP
ONFA N TEMP LAMP
ONFA N TEMP LAMP
ON
(Red lit) (Red lit)
(Red lit)                 (Red lit) (Green lit)
Or
(Orange lit)
Or
(Orange lit)(Red lit
or flashing) (Red lit)
3
Remove the lamp cover.Loosen the screws and remove the lamp cover.
4
Pull out the lamp.Loosen the three screws holding the lamp in place,
and pull on the handle to remove the lamp.
5
Mount the new lamp.Align the orientation, press down until the bottom is
reached, and lock in place using the three lamp
locking screws.
6
Replace the lamp cover.Align the cover, and press it in, then screw in the
screw loosened in step 
3 until the lamp cover is
no longer loose.
7
Reset the lamp timer.See the lamp’s manual for instructions on resetting
the lamp timer.Notes and Precautions•Press the 
 button twice to display (a rough guide) of the time of use from the Lamp
time item on the Status display menu. 
p.26
•As a rule of thumb, it is recommended that the lamp should be replaced after 1,500
hours of use.  When Lamp time reaches 1,500 hours, the 
 icon and a message will
appear.  When pressing the 
 button, the message disappears.
•Attach the lamp cover correctly so that it is not loose. If it is not attached correctly, the
lamp may fail to come on 
p.33
, and the lamp’s lifetime may be shortened.
•Always replace the lamp with a new one.
•The lamp is made out of glass.  Do not touch the glass surface with your bare hands,
bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)
Used LampsThis projector’s lamps contain trace amounts of environmentally harmful inorganic
mercury.  Be careful not to break used lamps, and dispose it in accordance with local
regulations.
Lamp replacement (Continued)
2
1
2
12
1
345 
						

							35
Others
34
SpecificationsList of general specifications
Item Specification
Consumption Power 340 WWeight 2.4 kg
External Dimensions 248 × 90 × 201 mm (W × H × D)(including protruding parts)Cabinet material Magnesium alloy, Aluminum alloyConditions for usage
 environment
Temp: 0°C to 35°C; relative humidity: 30% to 70%
Display system DLP
TM (1-tip DMD
TM)
Native resolution 1,024H × 768V  XGALens Zoom lens F=2.4-2.6 f=24.19-30.65 mmLamp High-pressure mercury lampProjection screen size 37 - 180 inchesProjection distance 1.5 - 6 mSpeaker 1 W (Monaural)
COMPUTER IN terminals
Mini D sub 15 pin   RGB / Y/P
B/PR (dual use)
MONITOR OUT terminal Mini D sub 15 pin   RGB / Y/P
B/PR (dual use)
S-VIDEO terminal Mini DIN 4 pinVIDEO terminal RCA Pin Jack, 1 V (p-p), 75 ΩAUDIO IN terminal 3.5 mm dia. stereo mini-jack, 1.5 V (rms); 22 kΩ or moreAUDIO OUT terminal 3.5 mm dia. stereo mini-jack, 1.5 V (rms); 8 Ω or moreCONTROL terminal Mini DIN 8 pin (RS-232C)
USB terminal Type B (USB 1.1) If you think something is wrong, check the following before contacting customer service.
Please see “Trouble indications” 
p.33
 as well.
If  This Happens Check
No powerPower goes out
during useNo pictureNo audioPicture not
displayed
correctlyPicture blurred
Part of picture
out of focusImage is darkColors too light
Bad shadingRemote control
doesn’t workBefore calling service personnel
•Is the power cord plugged in? Is it connected to the projector?
•Is the lamp cover loose? 
p.33
•Is the ambient temperature high? 
p.33
•Is the air intake or air exhaust blocked? 
p.33
•Is the input source selecting properly? 
p.21
•Is the mute function on? 
p.24
•Is the brightness setting minimized? 
p.28
•Are the connections set up correctly? 
p.18
•Are all the connected devices functioning properly?
•Is a plug inserted to AUDIO OUT terminal? 
p.18
•Is the mute function on? 
p.24
•Is the volume setting minimized? 
p.22
•Are the connections set up correctly? 
p.18
•Are all the connected devices functioning properly?
•Is the input signal supported by the projector? 
p.36
, p.37
•Is the correct video mode selected? 
p.23
•Is the correct signal format selected?  
p.23
•Is the selecting of computer or Y/P
B/PR input correct? 
p.21
•Is there something generating an abnormal video signal, for
instance the video tape?
•Is the lens dirty? 
p.31
•Is the lens focus adjusted optimally? 
p.22
•Is the projection distance within the projector’s supported range?p.17•Is the projector’s screen placement angle tilted too far?  
p.17
•Are the sharpness or sampling phase adjustments off? 
p.28
 p.23
•Are the brightness or contrast adjustments off? 
p.28
•Is the lamp nearing the end of its service life? 
p.26
•Are the color, tint, R-level, G-level, or B-level adjustments off? 
p.28
•Is the screen dirty?
•Is the lamp nearing the end of its service life? 
p.26
•Are the remote control’s batteries drained?
•Are the batteries inserted into the remote control correctly? 
p.16
•Is the remote control being used within the effective range? 
p.16
•Are there any obstructions between the remote control and
projector?
•Are there any fluorescent or other bright lights shining at the
projector’s infrared remote sensor?
Connection terminal 
						

							37
Others
36
Specifications (Continued)
List of supported signals (Y/P
B/P
R signals)
Signal format fh(kHz) fv(Hz)
480i(525i)@60Hz15.73 59.94
480p(525p)@60Hz31.47 59.94
576i(625i)@50Hz15.63 50.00
576p(625p)@50Hz31.25 50.00
720p(750p)@60Hz45.00 60.00
720p(750p)@50Hz37.50 50.00
1080i(1125i)@60Hz33.75 60.00
1080i(1125i)@50Hz28.13 50.00
1035i(1125i)@60Hz33.75 60.00
1152i(1250i)@50Hz31.25 50.00
List of supported signals (Video, S-Video signals)
Video mode fh(kHz) fv(Hz) fsc(MHz)
NTSC 15.73 60 3.58
PAL 15.63 50 4.43
SECAM 15.63 50 4.25 or 4.41
PAL-M 15.73 60 3.58
PAL-N 15.63 50 3.58
PAL-60 15.73 60 4.43
NTSC4.43 15.73 60 4.43
Pin assignment of COMPUTER IN terminal
5
1 10 15
11
6
Mini D sub 15 Pin connector
Input Signal
•RGB inputR/G/B signals: 0.7V (p-p) 75 Ω
Horizontal sync signal: TTL level (Pos/neg polarity)
Vertical sync signal: TTL level (Pos/neg polarity)•Y/P
B/PR input
Y signal: 1.0V (p-p) 75 Ω
PB/PR signals: 0.7V (p-p) 75 Ω
∗ Do not connect anything.Pin Pin descriptionNo. During RGB input
During Y/P
B/PR input
1
Video signal (R)
Color difference signal (P
R)
2 Video signal (G) Luminance signal (Y)3 Video signal (B)
Color difference signal (P
B)
4 GND∗5 GND∗6 GND (R) GND (P
R)
7 GND (G) GND (Y)8 GND (B) GND (P
B)
9 N.C∗10 GND∗11 GND∗12 DDC data∗13 Horizontal sync signal∗14 Vertical sync signal∗
15 DDC clock∗
List of supported signals (RGB signals)This projector supports the following RGB signals. Note, however, that depending on the
computer model, the screen may show flicker or streaking. Please adjust the projector if
this happens.
(Press the AUTO SET button, and adjust automatically or manually.  
p.23
 )
Mode
720x400_85
VGA_60
VGA_72
VGA_75
VGA_85
SVGA_56
SVGA_60
SVGA_72
SVGA_75
SVGA_85
MAC16
XGA_43i
XGA_60
XGA_70
XGA_75
XGA_85
MAC19
SXGA1_75
QuadVGA_60
QuadVGA_85
SXGA3_60
SXGA3_75
SXGA3_85
SXGA+
UXGA_60
UXGA_65
UXGA_70
UXGA_75
UXGA_85
1792x1344_60
1856x1392_60
1920x1440_60Refresh rate
(Hz)
85.039
59.940
72.809
75.000
85.008
56.250
60.317
72.188
75.000
85.061
74.550
86.957
60.004
70.069
75.029
84.997
74.700
75.000
60.000
85.002
60.020
75.025
85.024
60.012
60.000
65.000
70.000
75.000
85.000
60.000
60.000
60.000H-frequency
(kHz)
37.927
31.469
37.861
37.500
43.269
35.156
37.879
48.077
46.875
53.674
49.725
35.522
48.363
56.476
60.023
68.667
60.134
67.500
60.000
85.938
63.981
79.976
91.146
63.973
75.000
81.250
87.500
93.750
106.250
83.640
86.333
90.000Clock
(MHz)
35.500
25.175
31.500
31.500
36.000
36.000
40.000
50.000
49.500
56.250
57.283
44.900
65.000
75.000
78.750
94.500
79.857
108.000
108.000
148.500
108.000
135.000
157.500
118.094
162.000
175.500
189.000
202.500
229.500
204.750
218.250
234.000 Resolution
720 x 400
640 x 480
800 x 600
832 x 624
1024 x 768
1152 x 864
1280 x 960
1280 x 1024
1400 x 1050
1600 x 1200
1792 x 1344
1856 x 1392
1920 x 1440
Note•Signals whose resolution exceeds the native resolution (1,024 x 768 pixels) will be
compressed. For this reason, some information may be lost, or image quality may be
affected. 
						

							38

CONTROL terminal
Pin assignment
78 6 34
5 12
Signal Name
RXD
CTS
DSR
GND
RTS
N.C
TXD
N.C Pin No.
1
2
3
4
5
6
7
8Description
Receiving data
Consent to send
Data set ready
Signal ground
Request to send
No connection
Sending data
No connection
Mini DIN 8 pin connector
Interface format
1 Communication method RS-232C, 9600bps, No Parity, Data Length: 8 bits;
Stop Bit Length:  1 bit
2 Communication format STX (02h)  Command (3Byte)  ETX (03h)
Only 1 command valid per communication.
3 Data format For input commands, only ASCII-compliant all-uppercase
alphanumeric characters supported.
4 Replies Acknowledge ACK (06h) CR (0Dh) Data .... Succeed
ACK (06h) ESC (1Bh) .... Failure
No acknowledge NAK (15h)
If commands are to be sent consecutively, wait for the replies from the projector before
sending the next command.
Main Commands
Note
• Contact your dealer for control cable and other commands.

Separately Sold Product
Replacement Lamp Model NO.; for TDP-D1: TDPLD1, for TDP-D2: TDPLD2
Note
• Design, specifications, etc. subject to change without notice for improvements, etc.
Item Command
Power onPON
Power offPOF
Icon display onMO0
Icon display offMO1
Auto setting (RGB input)PAT
Status display onDON
Status display offDOF
Item Command
Computer input selectIN1
Y/PB/PR input selectIN2
Video input selectIN3
S-video input selectIN4
Specifications (Continued)