Sim2 Multimedia Grand Cinema C3x Lite Projector User Manual

cod. 46.0533.000
User and Installation Manual
c3X - c3X LITE  



MENUSOURCEESC

Switches off to stand-by
Activates the On Screen  Display MenuNavigates menu pages
▲,▼,◀,▶
Navigate through andmake adjustement to the On Screen Menu
Display the sourceSelection Menu
Deactivates the On Screen Menu
1  TELECOMANDO E TASTIERA DI CONTROLLO
LIGHT
F1ZOOM
FOCUSF2
0-9 KEYSSwitch  on  from  stand-by  mode  and  allow  direct source selection
STAND-BYSwitches off to stand-by
ESCAPEDeactivates the On Screen Menu
UP/DOWN/LEFT/RIGHT ARROW KEYSNavigate  through  andmake...

3

Adaptation of the input signal resolution to the Projector resolution oc-curs without alterations of image quality, in accordance with an ample choice of aspect ratios, including several definable by the user.
All image adjustments can be performed with the remote control with the aid of the On Screen Display; alternatively, the unit can be controlled by from a home automation system through the serial port.
SIM2 carries out comprehensive functional testing in order to gua-
rantee the maximum product...

4

ATTENTION:
To reduce the risk of electric shock, disconnect the power supply cable on the rear panel before removing the top cover of 
the projector. Refer to trained, authorised personnel for technical assistance.
Prior to switching on the projector please read each chapter of this manu\
al carefully as this manual provides basic instructions for using the projector.The installation of the lamp assembly, preliminary adjustments and procedures that necessitate the removal of the top cover, must be...



•   Read this manual carefully and keep it in a safe place for future 
consultation.
	 This 	 manual 	 contains 	 important 	 information 	 on 	 how 	 to 	 install 	 and 	
use 	 this 	 equipment 	 correctly. 	 Before 	 using 	 the 	 equipment, 	 read 	
the 	 safety 	 prescriptions 	 and 	 instructions 	 carefully. 	 Keep 	 the 	 manual 	
for 	 future 	 consultation.
• 
  Do not touch internal parts of the unit.
	 The
	 unit 	 contain 	 electrical 	 parts 	 carr ying 	 high 	 voltages 	 and...

6

 Replace the safety fuse
 Before  making  the  replacement  disconnect  the  appli-
ance from the mains power supply.
 The  fuse  compartment  is  close  to  the  mains  power  con-
nector (Fig. 3). Use a slotted screwdriver to remove the fuse 
carrier () and replace the fuse (3). Insert a new spare fuse 
(4). Use only T 5A H fuses.
Fig.3
•  Beware of power supply cables. Position the power supply cables so that they do not consti-tute an obstruction. Position the power supply cables where they...

7

1
2
3
4

3  UNPACKING
To  unpack  the  projector  safely  and  easily  please 
follow steps 1 to 5, as per drawing (Fig. 4).
It is recommended that the carton and packaging is 
retained for future use and in the unlikely event that 
your projector needs to be returned for repair.
Fig.4
PACKAGE CONTENTS
Fig.5
The carton should contain the following:
-  the projector  
- the remote control
- four 1.5V AAA batteries (for remote control)
- three  power  cables  for  the  projector  (EU,  UK, 
USA)
- the...

8

CAUTION:  In  the  case  of  ceiling  or  wall  mounting  using  a 
suspension  bracket,  follow  the  instructions  carefully  and 
comply  with  the  safety  standards  you  will  find  in  the  box 
together with the bracket. If you use a bracket different to 
the one supplied by SIM2 Multimedia, you must make sure 
that  the  projector  is  at  least  65  mm  (2-9/16  inch)  from  the 
ceiling and that the bracket is not obstructing the air vents 
on the lid and on the bottom of the projector....

9

+12VUSB 1. 1R/CrCON TROL (R S232)GRAPHIC S RGBC/YB/CbHVS-VIDEOAUDIO OUTHDMI 1REMO TE32S-VIDEOMENUESCINPUT154
0I
TRAPEZIO 
20%

  
Fig. 8a
The  Orientation  adjustment  in  the  Set  up  menu  will  allow  the 
projector to be used for desktop front, ceiling front, desktop rear 
and ceiling rear installations (Fig. 9).
+12VUSB 1.1R/CrCONT ROL (RS2 32)GRAPHICS RGBC/YB/CbHVS-VIDEOAUDIO O UTHDMI 1REMOTE32S-VIDEOMENUESCINPUT154
0I
Fig. 9
To  activate  an  electric  motorised  screen  a  1  Volt...

10

5   SWITCHING ON AND OFF THE PROjECTOR
ACAUTION: Connect the projector to a power supply with a 
nominal voltage within the following values:  100-240 Vac, 
50/60 Hz. It must be earthed (Fig. 12).
GRAPHICS RGBHVS-VIDEO
AUDIO OUT
HDMI 1
REMOTE
2S-VIDEO
MENU
ESCINPUT
1
5
4
0I
Power Switch:Position I: OnPosition 0: Off
FusedPower Socket
Power Plug
Fig. 1
Upon switch on (in position I) the projector will initialise (red and 
green LEDs on).
Followed by stand-by mode (red LED on)  (Fig. 13).
HDMI...