Samsung Syncmaster Nc190 User Manual

							Installing the Product2-1
2 Installing the Product
2-1 Package Contents
 • Unpack the product and check if all of the following contents have been included.
• Store the packaging box in case you need to move the Product at a later stage.
 
Monitor
CONTENTS
Quick Setup Guide Product Warranty User Manual Power Cord
OPTIONAL PARTS
Keyboard (USB) Mouse (USB)D-Sub Cable
 
						

							2-2Installing the Product
2-2 Installing the Stand
 Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards. 
Place a soft cloth over the table to protect the product and place the product onto the 
cloth so that the front of the product is facing downwards.
 Do not remove 
the stopper pin before installing the base. 
Hold the main body of the product with your hand as shown by the figure.
Insert the stand base into the stand connection part in the direction shown in the figure.
Turn the connecting screw at the bottom of the stand fully so that it is completely fixed. 
 
						

							Installing the Product2-2
 Disassembly is in the reverse order of assembly. 
After the installation of the base, stand the monitor up as shown in the figure. Now you 
can remove the stopper pin to adjust the stand.
- Caution
Avoid lifting the product holding only the stand.
 
						

							2-3Installing the Product
2-3 Installing a Wall Mount
 Before installation, disassemble the product according to the following steps. 
This product provides a wall mount of 100 mm x 100 mm(200 mm x 100 mm) that complies with the VESA specifications.
1. Turn the product off and unplug the power cord from the wall outlet.
2. Place a soft cloth or cushion on a flat surface to  protect the panel and place the product face down.
Lift up the monitor stand to the maximum angle with your left hand, and remove the back 
decoration cover with your right hand, as shown in the figure.
Remove the two screws(A).
Remove the stand arm in the direction shown in the figure.
100 mm x 100 mm 200 mm x 100 mm
A. Wall Mount Base
B. Wall Mount Kit (Optional)
 
						

							Installing the Product2-3
3.Separate the stand.
4. Align the groove of the Monitors wall mo unt base with the groove in the wall mount ki  and firmly fix the wall mount kit by 
fastening the screws.
 •If you use a screw that is longer than the standard s pecifications, the inside of the product may be damaged.
•For wall mounts that are not compatible with the standard VESA specific ations, the length of the screw may differ depending 
on the corresponding specifications.
•Do not use screws that are incompatible with the standard VESA  specifications and do not assemble them using excessive 
force.
This may result in damage to the product or injury due to th e product falling. Samsung shall not be held liable for any damage 
or injury.
•Samsung shall not be held liable for any damage to the product or  injury caused by using a stand that is not compatible with 
the specified specificat ions or due to an installation not performed by an authorized installation engineer.
•When installing the product using a wall mount, purchase  a wall mount that provides at least 4 inches (10 cm) of space from 
the wall.
•Samsung shall not be held liable for any problems caused by  using a stand that is not compatible with the specified 
specifications.
•Use a wall mount according to specifications of your country.
 
 
						

							2-4Installing the Product
2-4 Connecting to your Network
 The connecting part may differ depending on the product model. 
Connect between the [LAN] port on the product and your network using a LAN cable.
 The two [LAN] ports are designed to work as an Internet HUB . One port can be used for input and the other port for output 
to connect the product to an external Internet device . Both ports can be used for either input or output.
 
•U se Cat5(*STP Type) cable for the connection.
*Shielded Twist Pair (NC190 Only)
 
						

							Installing the Product2-5
2-5 Connecting Power
To use the product, connect the power cable to a power outlet and the [POWER] port on the product.
(The input voltage is switched automatically).
 
						

							2-6Installing the Product
2-6 Connecting to another Monitor
Please select the right connection method for your monitor.
• When using the [RGB OUT] port
• Connect between the [RGB OUT] port on the product and  the D-Sub port on your monitor using a D-Sub cable.
• When using the [DVI OUT] port • Connect between the [DVI OUT] port on the product and the DVI port on your monitor using a DVI cable.
 Connect to the  [DVI OUT], [RGB OUT ] port to display the same picture on another monitor such as the projector. 
 (For presentation purposes)
 
 
						

							Installing the Product2-7
2-7 Connecting with a PC
 Connect the [RGB IN] port of the product to the [D-Sub] port of your PC with a D-Sub cable. 
 Use the [RGB IN] port to directly connect the monitor to a PC.
 
 
						

							2-8Installing the Product
2-8 Connecting a Stereo Cable
Connect the [AUDIO IN] port on the rear side of the monitor to the sound card of the PC.