Philips 32pm8822 Installation Guide

							BDS Mirror TV Application Note 
 Release v0.5 
 
 
 
6.1 Mirror TV – External Speaker Connectors 
 
The Mirror TV provides  outputs to connect build on/remote speakers.  Refer to 
the following picture: 
 
 
 
 
 
 
 
 
 
 
 
• To connect build on/remote speakers to the Mirror TV, follow these directions: 
o Turn off the Mirror TV and unplug the mains power cord 
o Connect the cables from the external speakers to the speaker connectors on 
the Mirror TV 
o Secure the speaker cables by fastening the latches of the external speaker 
connector 
o Connect the mains power cord back into the power outlet and turn on the 
Mirror TV 
 
• To toggle the audio output between the internal speakers and the external speakers, 
flip the Internal/External Speaker switch. 
 
 
Important points to note when connecting external speakers 
 
• To ensure that the correct types of external speakers are connected to the Mirror TV, 
refer to the chart below: 
 
Mirror TV Model Impedance Power 
     32” -  42”  8 Ohms 15 W 
 
• When connecting remote speakers, take extra precaution to ensure that the speaker 
impedance is correct and to prevent possible shorting of the speaker terminals. 
Incorrect use may cause damage to the audio amplifier of the Mirror TV 
 
• To remove the remote or build on speakers, ensure that the power to the Mirror TV is 
turned off, before removing the speakers from the connectors. 
 
 
 
 
 
 
Copyright © Philips BDS-ITV 2005 11
 
						

							BDS Mirror TV Application Note 
 Release v0.5 
 
 
 
6.2 Mirror TV – Main Power Button 
 
The main power button of the Mirror TV is located differently as compared to the 
conventional 32”- 42” LCD TV. It is located on the side of the back plate of the 
Mirror TV. Refer to the following picture: 
 
 
 
 
 
 
 
 
 
 
 
     
MMaaiinn  
PPoowweerr  
BBuuttttoonn 
Important points to observe when operating the Mirror TV that is in-wall mounted 
 
If the Mirror TV is mounted into a wall recess, the main power button may not be 
easily accessible. In such a scenario, it is advised that: 
 
• All connections and fine-tuning of TV settings be completed before the Mirror 
TV is mounted into the wall recess.  
• This means that the Mirror TV should be connected to the power mains, and 
switched on using the Main Power button. With the Mirror TV switched on, 
configure the required TV settings. 
• After the settings have been configured, do NOT switch off the Mirror TV via 
the Main Power button. Instead, set the Mirror TV to ‘standby’ mode via the 
Remote Control unit 
• When the Mirror TV is now powered down in ‘standby’ mode, turn off the 
power mains. Disconnect the Mirror TV from the power mains, and proceed to 
mount the Mirror TV. 
• Once the Mirror TV is mounted properly, reconnect the power mains and turn 
on the power mains switch. The Mirror TV should be in ‘standby’ mode. 
• To turn on the Mirror TV, use the Remote Control to wake the Mirror TV 
from ‘standby’ mode. Subsequent control of the Mirror TV (including switching 
on/off) should be via the Remote Control. 
 
 
 
 
 
 
 
 
 
 
Copyright © Philips BDS-ITV 2005 12
 
						

							BDS Mirror TV Application Note 
 Release v0.5 
 
 
 
Annex A Custom Decorative Frame Profile 
 
Provided below are the recommended dimensions for the design and construction of custom 
decorative frames for the Mirror TV. (dimensions in  
mm/inches) 
                     
                                   Decorative frame profile for 32” 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
                                  
                              
 
 
 
 
 
 
                                  Decorative frame profile for 42” 
 
 
 
 
 
 
 
 
 
 
 
Copyright © Philips BDS-ITV 2005 13
 
						

							BDS Mirror TV Application Note 
 Release v0.5 
 
 
 
Annex B Decorative Frame Dimensions for Mirror TV 
 
Provided below is the decorative frame dimensions for the 32”- 42” Landscape model of the 
Mirror TV.  
 
                                            32” Landscape Mirror TV 
   
 
 
 
 
 
 
 
  
  
 
 
 
 
                                              42” Landscape Mirror TV 
 
                                      
 
 
 
 
 
 
 
 
 
 
 
 
Annex C
 Wall Mounting the Mirror TV landscape/portrait 
 
Follow these steps to mount the Mirror TV onto the wall. 
 
1. Secure the Wall mount bracket onto the wall, as shown: 
Copyright © Philips BDS-ITV 2005 14
 
						

							BDS Mirror TV Application Note 
 Release v0.5 
 
 
 
 
  
 
2. Secure the Mirror TV onto the Wall mount bracket, as shown: 
 
 
 
 
 
Copyright © Philips BDS-ITV 2005 15
 
						

							BDS Mirror TV Application Note 
 Release v0.5 
 
 
 
 
 
Portrait     
 
 
 
Landscape
Copyright © Philips BDS-ITV 2005 16
 
						

							BDS Mirror TV Application Note 
 Release v0.5 
 
 
 
 
Annex D Recessed Wall Mounting the Mirror TV  
1.  Required measurements of the wall 
                       Wooden frame for 32” (not included). 
 
 
 
 
 
 
 
 
 
                       Wooden frame for 42” (not included).        
                    
 
 
 
 
 
 
 
 
 
 
 
 
 
Copyright © Philips BDS-ITV 2005 17
 
						

							BDS Mirror TV Application Note 
 Release v0.5 
 
 
 
 
 
2. Wall fixing to be installled according drawing. 
 
    
Wall
Tapping screw DIN 7981 C-HST4.2 x 38
Mirror TV Unit
with clicking devicesDecorative Frame 
Wooden framel
Fixing Bracket
 
Copyright © Philips BDS-ITV 2005 18
 
						

							BDS Mirror TV Application Note 
 Release v0.5 
 
 
 
3. 32” landscape mirror TV in-wall mouting (pg. 1/2) 
Note: If you are considering mounting the  32PM8822 landscape mirror TV in an 
in-wall installation, the installation must conform to all applicable safety 
requirements. Additionally, the installation must conform to the ventilation 
requirements as described below. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Copyright © Philips BDS-ITV 2005 19
 
						

							BDS Mirror TV Application Note 
 Release v0.5 
 
 
 
3.  32” landscape mirror TV in-wall mouting (pg. 2/2) 
 
 
 
 
 
Copyright © Philips BDS-ITV 2005 20