Panasonic Network Camera Wv Sud638 Installation Guide
Have a look at the manual Panasonic Network Camera Wv Sud638 Installation Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Camera
Sun Shade
Dummy cover
or IR LED unit
(optional)
Front glass
Wiper
PAN rotation part
Mounting pedestal
Tilt arm
Tilt lock
Side cover
Bottom wiring port Side wiring port
Mounting pedestal
fixing screws ×4
(locally procured) Dummy cover or IR LED unit
(optional)
IMPORTANT:
•
When the camera is initialized, the settings including the network settings will be initialized. Note that the
CRT key (SSL encryption key) used for the HTTPS protocol and the preset entry will not be initialized.
• Before initializing the settings, it is recommended to write down the settings in advance.
• Do not turn off the power of the camera during the process of initialization. Otherwise, it may
fail to initialize and may cause malfunction.
STATUS indicator behaviors
• When the power is turned on
Lights orange → Lights off → Blinks orange → Lights orange (When the network connection is not established) Lights orange → Lights off → Blinks orange → Blinks green → Lights green
(When the network connection is established)
• During the standby or connection
Lights orange (When the cable is not connected)
Lights green (When the cable is connected)
• During the upgrade process
Blinks orange
• During the initialization
Lights orange → Lights off → Blinks orange →
Lights orange
• Port forwarding error caused by the UPnP function
Blinks orange (in 2 seconds intervals
(on for 1 second / off for 1 second))
• Trouble happening on the camera
Blinks red
• When the installation position is abnormal
Lights red
• This manual describes the installation procedures, network camera installation, cable connec-
tions, and adjustment.
• Before reading this manual, be sure to read the Important Information (included in the CD-ROM).
Parts and functions
Standard accessoriesCable preparation
Important safety instructions ......................... 1 pc.
Installation Guide (this document) ................. 1 setWarranty card*1 ............................................
1 set
CD-ROM*2 .................................................... 1 pc.
Code label*3.................................................. 1 pc.Attach the provided waterproof connector to the cable to be connected to the camera.
* When a conduit is used for wiring, always check its size before installing the waterproof connector.
Otherwise, the cable may not be able to pass through the conduit depending on the number of cables
used and the waterproof connector in use.
* Always make preparations before the procedure “[3] Attach the waterproof RJ45 connector (acces- sory) to the Ethernet cable.”
* Prepare [1] and [2] when necessary.
*1
This product comes with several types of warranties. Each warranty is only appl\
icable to the prod-
ucts purchased in the regions indicated on the relevant warranty.
*2 The CD-ROM contains the operating instructions and different kinds of tool software programs.
*3
This label may be required for network management. The network administrator shall retain the code label.
Waterproof power supply connector (plug side) ........................................................................\
....... 1 set
Waterproof EXT I/O connector (plug side) ........................................................................\
................ 1 set
Waterproof RJ45 connector (plug side) ........................................................................\
.................... 1 set
Washer nozzle mounting bracket A ........................................................................\
.......................... 1 pc.
Washer nozzle mounting bracket B ........................................................................\
.......................... 1 pc.
Fixing screws for the washer nozzle mounting bracket B .............................. 3 pcs. (of them, 1 for spare)
Attachment plate ........................................................................\
..................................................... 1 pc.
Fixing screws for attachment plate ................................................................. 5 pc. (of them, 1 for spare)
Fixing nuts for attachment plate ..................................................................... 5 pc. (of them, 1 for spare)
Spring washer ........................................................................\
....................... 5 pc. (of them, 1 for spare)
Flat washer ........................................................................\
.......................... 10 pc. (of them, 2 for spare)
Safety wire ........................................................................\
............................................................... 1 pc.
Wire clamper ........................................................................\
........................................................... 1 pc.
Bit (Hex wrench, screw size 6.35 mm {1/4 inches} T20) ...................................................................1 pc.
Hub/Router
AC100-240 V
50/60 Hz
Ethernet cable (category 5e or better, straight)
Ethernet cable (category
5e or better, straight)
PC*
2
Tested PoE injector*1
Installation procedure
• Attach the provided waterproof connector to the cable to be wired to the inside of the ceiling or
floor or along various surfaces, and run the cable through the conduit. (Please choose a conduit
of a suitable size to allow the connector to pass through.)
Cable preparation
• Remove the side cover of the camera so that the wire connection part is visible. (Step.4)
• If necessary, install the extension unit (IR LED unit) (optional) if necessary. (Step.5)
• If you want to shoot the foot area, bend the tilt arm of the camera forward. (Step.6)
• Fix the camera onto the installation location. (Step.8)
* Install the washer nozzle mounting bracket pre-fitted with a (recommended) washer nozzle at the
same time.
Installation
• Connect each waterproof connector to the camera, and fix the side cover back to its original\
position.
Connecting wires
(→ Refer to the leaflet “Configuring
the camera so that it can be
accessed from a PC”)
• Turn on the power supply, and configure the camera so
that it can be accessed via network.
Configuring the camera so that it can be accessed from a PC
• About the INITIAL SW (Initial switch)
Follow the steps below to initialize the network camera.
➀ Cut the power supply to the camera either by unplugging the AC power cord or by turning off the
power supply of the tested PoE injector.
➁ Turn on the power of the camera while holding down the INITIAL SW, and keep the INITIAL SW held
down for 10-15 seconds. In about 2 minutes after releasing the INITIAL SW, the camera will start up
and the settings, including the network settings, will be initialized.
System connection diagram
The camera can be powered by the AC power supply or the tested PoE injector as shown in the fol\
low-
ing illustration.
*1 For the related information on applicable tested PoE injectors, refer to our website
(http://security.panasonic.com/support/info/).
*2 Use an Ethernet cable (category 5e or better, cross) when directly connecting the camera to a PC.
[1] Attach the waterproof EXT I/O connector (accessory) to the cable
* The parts to be used in ➁ and ➂ are in the bag of the waterproof EXT I/O connector (plug side) set.
• Multi-core cable ø6.2 ~ 7 mm {ø1/4 ~ 9/32 inches}
Size of the internal lead wire
AWG26 – AWG30, coated external diameter of ø1 mm {ø1/32 inches} or below
• Manual crimping tool HT-102/HR30-1, made by Hirose Electric Co., Ltd.
• Extraction tool (if necessary) HR30-TP, made by Hirose Electric Co., Ltd.
➀ Thread each part of the waterproof EXT I/O connector (accessory) through the cable in
sequence
Pass the cord tube, cord clamp, gasket, spring and coupling in sequence through the plug beforehand.
Prepare wire ends according to the dimensions shown in the illustration below.
Case block CouplingSpringCord clamp
Gasket Cord tube
Cable
15 ~ 20 mm {19/32 ~ 25/32 inches}
2.0 mm (+0, -0.5)
{3/32 (+0, -1/32) inches}
➁ Crimp the contact (accessory) to the cable
➂ Insert the contact into the terminal hole on the
case block
• After inserting the contact, pull the lead wire lightly, and ensure that it is firmly fixed to the terminal hole
of the waterproof EXT I/O connector.
Pin. 1 LINE IN Pin. 7 Alarm IN1
Pin. 2 Audio/LINE_GND Pin. 8 N.C.
Pin. 3 Audio OUT Pin. 9 Relay-
Pin. 4 Alarm GND Pin. 10 Relay-
Pin. 5 Alarm IN3/AUX Pin. 11 Relay+
Pin. 6 Alarm IN2/Alarm OUT Pin. 12 Relay+
➃ Mount the coupling and the spring on the case block, and tighten the cor\
d tube with the gasket
and the cord clamp
• Align the mark “
” on the coupling
with the side of pin
➀ of the case block,
and install the coupling and the spring in
sequence.
• Shift the cord tube, and insert the cord clamp and the gasket in the cord tube.
• Align the cord tube with the coupling part, and rotate to tighten them as shown in the
right illustration. (Recommended tightening
torque: 0.5 N·m {0.37 lbf·ft})
➄ Connect the washer unit (locally procured)
Pin. 9 Relay-
Pin. 10 Relay-
Pin. 11 Relay+
Pin. 12 Relay+
Waterproof EXT I/O
connector side
Circuit diagram
Washer unit connection
terminal side
Washer-
Washer+
Nozzle Washer hose
* Please use the washer unit that has been insulated from the commercial AC power.
➅ EXT I/O terminal ratings
• Alarm IN1, Alarm IN2, Alarm IN3
Input specification: No-voltage make contact input (4 V ~ 5 V DC, internally pulled up)
OFF: Open or 4 V ~ 5 V DC
ON: Make contact with GND (required drive current: 1 mA or more)
• Alarm OUT, AUX OUT
Output specification: Open collector output (maximum applied voltage: 2\
0 V DC)
OPEN: 4 V ~ 5 V DC by internal pull-up
CLOSE: Output voltage 1 V DC or less (maximum drive current: 50 mA)
• Max. ratings of Relay+ and Relay-: DC 25 V, 4.0 A
* The default of EXT I/O terminals is “Off”.
[2] Attach the waterproof power supply connector (accessory) to the cable
* The parts to be used in ➀ and ➁ are in the bag of the waterproof power supply connector (plug side) set.
• Power cable
Cable diameter
ø6 ~ 10 mm {ø1/4 ~ 13/32 inches}
Cross-sectional area of the wire conductor 0.75 or 1.25 mm2 {0.0012 or 0.0019 inche2}
Number of wires 3 (for L, N and FG)
Insulation material Polyethylene (recommended)
➀ Preparations
• Assemble the internal strain relief as shown in the right illustration, and install the fixing bracket.
(Tighten the screws temporarily as the power cord will go in between
the bracket and the formed part.)
• Install the mounting gasket on the clamp
ring as shown in the right illustration. (Please
use the applicable parts as described below
for the mounting gasket according to the
external diameter of the power cord.)
Small internal diameter...
Power cord size 6.0 ~ 9.0 mm {1/4 ~ 11/32 inches}
Large internal diameter...
Power cord size 9.0 ~ 10.0 mm {11/32 ~ 13/32 inches}
➁ Thread each part of the waterproof power supply connector through the po\
wer cable in
the sequence as shown in the illustration below
• Cable nut
→ Clamp ring (with mounting gasket) → Back shell → Internal strain relief
Internal strain relief Back shell
Clamp ring (with
mounting gasket)Cable nutCable
➂
Prepare the cable end in the following dimensions, and twist the core.
Process tolerance: +1 mm/-0 mm {+1/32 / -0 inches}
Dimensions A (cable sheath) Dimensions B (bare core wire)
Live, Neutral18 mm {23/32 inches} 7 mm {9/32 inches}
GND 20 mm {25/32 inches} 9 mm {11/32 inches}
➃ While the core of the lead wire is inserted into the connecting hole at the back of the
connector body, tighten the screw on the connector body, and connect
and fix the lead wire to each terminal.
For safety purpose, please read the following connection instructions ca\
refully.
* There is a cutout on the connector coupling nut.
Align the position of the screw to be tightened with the cutout on the coupling
nut, and tighten the screw with a flathead screwdriver. (Refer to the upper
right illustration.)
(Recommended tightening torque: 0.5 N·m {0.37 lbf·ft}
During fore position
During upright position
Clamp ring
Mounting
gasket
Small internal
diameter
Large internal
diameter
Case block
Waterproof EXT I/O connector (accessory)
Terminal layout of the contact insertion side
Connector Pin 1 Live Pin 2 Neutral Pin 3 N.C.
GND
Cutout
Coupling nut
Pin 2
Pin 1 Pin 3
GND
➄ Insert and fix the internal strain relief on the connector as shown in t\
he illustration. Next,
rotate the screw of the internal strain relief, and fix the power cord f\
irmly with the fixing
bracket.
(Recommended tightening torque: 0.5 N·m {0.37 lbf·ft})
➅ Align the coupling nut to the fixing position to prevent
the connector from rotating, and rotate to fix the back
shell. Install the clamp ring (with mounting gasket) on
the back shell, and tighten it with a cable nut.
(Recommended tightening torque: 1.5 ~ 2.0 N·m {1.11 ~ 1.48 lbf·ft}
Coupling nut Back shell Cable nut
Clamp ring
(with mounting gasket)
Screws × 2
Internal strain relief
Internal strain
relief (accessory)
Fixing bracket
(accessory)
Screws x 2
(accessory)
Pin ➀Coupling Spring
Cord tube (Including the cord clamp and the gasket)
Case blockInstallation Guide
Included Installation Instructions
Network Camera
Model No. WV-SUD638
WV-SUD638-H / WV-SUD638-T
(Natural silver)
(Gray) (Brown)
PGQX2063ZA fles0816-0 Printed in China
For U.S. and Canada:
Panasonic System Communications
Company of North America,
Unit of Panasonic Corporation
of North America
www.panasonic.com/business/
For customer support, call 1.800.528.6747
Two Riverfront Plaza, Newark, NJ 07102-5490
Panasonic Canada Inc.5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada
(905)624-5010
www.panasonic.ca For Europe and other countries:
Panasonic Corporation
http://www.panasonic.com
Panasonic System Networks Co., Ltd.
Fukuoka, Japan
Authorised Representative in EU:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
© Panasonic System Networks Co., Ltd. 2016
Switch plate
STATUS indicator
ACT Indicator LINK indicator
INITIAL SW
(Initial switch)
ab
Connector body
2
4
3 5
76
8
56789
Cable preparation (continued)Installation
Connecting wires
Step.1 Preparations
➀ There are 3 methods to install the camera as follows.
In accordance with the conditions of the installation location, prepare the foundation of the installation
site, fix the installation support and the installation stand, and prepare for cable wiring.
• Stationary installation ∙ ∙ ∙ Install on a concrete stand, etc. (Side wiring)
• Pole installation ∙ ∙ ∙ Install on the top of a thick metal pole. (Bottom or side wiring)
• Ceiling installation ∙ ∙ ∙ Install on a concrete ceiling. (Side wiring)
➁ Procure locally the following parts depending on the camera mounting met\
hod used for the specific
installation location.
■ To weld the bolt on the installation stand
• M8 nut ........................................................................\
..................... 8 pcs. (To fix with double nuts)
• M8 flat washer / spring washer ........................................................................\
....... 4 pcs. for each
■ To cast the anchor on the installation stand
• M8 anchor / bolt ........................................................................\
............................. 4 pcs. for each
• M8 flat washer / spring washer ........................................................................\
....... 4 pcs. for each
■ To fix the safety wire
• M8 anchor / screw ........................................................................\
............................ 1 pc. for each
Step.2 Work on the installation surface.
Weld the bolt or cast the anchor on the installation site.
This section describes the case of fixing with screws by casting the anchor.
Listed below are the dimensions of the mounting portion (the position and fitting diam\
eters).
■
To fix the camera directly on the installation surface ■ To fix the camera with the attachment plate
R50.8 mm {2 inches}
Front viewFront view45°
45°
142 mm { 5-19/32 inches }4-ø10 mm
{13/32 inches}
4-ø10 mm
{13/32 inches}
170 mm {6-11/16 inches}
170 mm {6-11/16 inches}142 mm {5-19/32 inches}
Bottom view of WV-SUD638 Bottom view of the attachment plate
Step.3 Take the camera out of the packaging box.
Hold the handle of the protection bag, pull up the unit from the box, and put it upright as shown in the
illustration.
Step.4 Prepare for removing the side cover of the mounting pedestal
• Open the camera protection bag.
• Loosen the 2 side cover fixing screws with the bit (accessory),
and remove the side cover from the mounting pedestal.
Step.5 If necessary, install the IR LED unit
(WV-SUD6FRL1: Optional) to the camera.
For detailed installation instructions, refer to the Operating
Instructions of the IR LED unit.
Step.8 Mount the camera onto the installation surface.
■ To fix the camera directly on the installation surface ■ To fix the camera with the attachment plate
Camera fixing
screws × 4
(locally
procured)
Spring washers,
flat washers
× 4 each (locally
procured) Spring washer
× 4 (accessory)
Attachment plate fixing screws × 4 (locally procured)
Attachment
plate
(accessory)
Flat washer
× 8 (accessory)
Fixing nuts for attachment
plate × 4 (accessory)
Fixing screws for
attachment plate
× 4 (accessory)
IMPORTANT:
• Before lowering the camera onto the installation surface, thread cables or wires through the
bottom wiring port or the side wiring port.
• Recommended tightening torque for mounting the attachment plate: 11.76 N∙m {8.67 lbf·ft}
•
Min. pull-out strength of fixing screws for the camera or the attachment plate ∙ ∙ ∙ 1539 N {346 lbf} (per 1 pc.)
Step.9 Fix the safety wire.
Fix the safety wire on the base of a building or on an area with sufficient strength (with a min. pull-out
strength of 1539 N {346 lbf} or above). Please procure M8 fixing screws locally in accordance to the
material of the installation location.
Perform Step 7 and subsequent steps at the installation location.
Exercise care when executing the steps.
Step.7 Install the safety wire (accessory) to the camera
Tilt the camera over sideways with the buffer material in the packaging material, and as shown in
the illustration below, install the wire clamper (accessory) and the safety wire (accessory) to the wire
mounting holes at the bottom of the camera.
Wire clamper
(accessory) Safety wire (accessory)
Wire mounting hole
Camera bottom
Note:
• Please peel off the release paper of the double-sided tape attached on the bottom side of the wire clamper before use.
• The safety wire can be pulled out from 2 directions. Install the wire clamper at the pulling direc- tion of the safety wire.
IMPORTANT:
• The installation surface is horizontal.
• To weld the anchor bolt to the mounting portion, the maximum part of the threaded length is
40 mm {1-9/16 inches} and the minimum is 30 mm {1-3/16 inches}.
• Minimum pull-out strength: ∙ ∙ ∙ 1539 N {346 lbf} (per 1 pc.)
• Fully consider the fixing screws for camera body or attachment plate fixing to installation area,
such as using corrosion resistance treated screws or performing caulking.
IMPORTANT:
• To operate the camera temporarily for settings or other
purposes, be sure to keep the camera in the upright
position when connecting it to the power supply. After the
camera is connected to the power supply, initial opera-
tions will begin automatically. Please ensure that the cam-
era is not obstructed by your hand or other objects when
it starts panning, tilting or performing other actions.
IMPORTANT:
• When using the camera in standing position, ensure that it does not topple over. Fix it temporarily on
the included attachment plate (see Step 8), or ensure proper support before any work is done on it.
• Use the handle of the protection bag only to take the camera out of its packaging box. Do not
use it to hang the camera in high places.
[1] Connect the waterproof EXT I/O connector (accessory) to the camera.
Alignment mark (C) Alignment
mark (D)
Part B
Part A Plug
Receptacle
Mounting portion
of the camera
• Remove the cap attached to the receptacle for the waterproof EXT I/O connector of the camera. (Do not remove the cap if the waterproof EXT I/O connector is not used.)
• During installation, align the alignment mark (D) on part A of the plug with the alignment mark (C) of
the receptacle, and push it straight in.
• To remove the plug when it is still connected, hold the coupling part B of the plug and pull it out
straightly.
Note:
• Always turn off the circuit’s power supply before connecting or disconnecting the connector.
• Insert the connector with a force of 30 N {6.74 lbf} or above.
• After the connector is connected, do not apply any load of 30 N {6.74 lbf} or above on the cable.
[2] Connect the waterproof power supply connector (accessory) to the camera.
• Remove the cap attached to the receptacle for the waterproof power supply connector of the camera. (Do not remove the cap if the waterproof power supply connector is not used.)
• During installation, align the guide of the plug with that of the receptacle, and then push it straight in. (The guides can be aligned by lightly inserting the plug on the receptacle and rotating the plug.)
• Rotate the plug’s coupling nut, and fix it firmly on the receptacle.
Recommended tightening torque: 1.0 ~ 1.5 N∙m {0.74 ~ 1.11 lbf∙ft}
Guide
Receptacle
Receptacle
Coupling nut Plug
Plug
Coupling nut
[3] Connect the waterproof RJ45 connector (accessory) to the camera.
• Insert the waterproof RJ45 connector into the receptacle of the camera. Receptacle Waterproof RJ45 connector
• Rotate the ring of the waterproof RJ45 connector, and fix it firmly on the receptacle.
Recommended tightening torque: 1.0 ~ 1.5 N∙m {0.74 ~ 1.11 lbf∙ft}
Ring
Receptacle Waterproof RJ45 connector
[4] Install the side cover.
Install the side cover removed in “Step 4 Prepare for removing the side cover of the mounting pedestal”
in “Installation.” back to its original position with 2 screws.
(Recommended tightening torque:1.5 N∙m {1.11 lbf·ft})
IMPORTANT:
• After installation and before connection to the power supply, please check the following items.
➀ Every waterproof connector is properly installed.
➁ The wiring and power supply voltage of the wired power cables are correct.
➂ The camera is not exposed directly to the sun or other light sources.
➃ There is no obstruction in the surroundings. (After the camera is connected to the power
supply, initial operations will begin automatically. Please ensure that the camera is not
obstructed by your hand or other objects when it starts panning, tilting\
or performing other
actions.)
[5] Remove the buffer material and the protection sheet from the camera.
[6] Connect the camera to the power supply.
For details on the follow-up procedure, refer to the leaflet “Configuring the camera so that it can be
accessed from a PC”.
Side cover
Side cover fixing screws × 2
Mounting
pedestal
Note:
•
Keep the removed side cover in a safe place as it will be
mounted again in the end.
IR LED unit
[3] Attach the waterproof RJ45 connector (accessory) to the Ethernet cable.
• Ethernet cable Use 4 pairs (8 pins in total). Max. length: 100 m [328 ft]; external diameter: ø5 mm ~ 6.5 mm {ø3/16 ~ 1/4 inches}
• Crimping tool for RJ45 plug (used for crimping the RJ45 plug to the Ethernet cable.)
➀ Crimp the RJ45 plug to the Ethernet cable, and thread the waterproof nut\
, the waterproof
rubber and the support rubber in sequence. (There are mounting slits on the waterproof rubber
and the support rubber.)
➁ Pass the RJ45 plug through the waterproof RJ45 connector.
(As shown in the lower left illustration, there is an outlet of the same shape as the RJ45 plug on the
waterproof RJ45 connector. Please take note of the direction and insert from the inside.)
Waterproof RJ45 connector
RJ45 plug outlet RJ45 plug
Support rubber
Waterproof rubber Waterproof nut
➂ Insert the support rubber and the waterproof rubber into the waterproof \
RJ45 connector.
(Insert the support rubber first, and then insert the waterproof rubber into the rear end of the
waterproof RJ45 connector until it touches the inside of the nail.)
The nail part on the rear
end of the waterproof
RJ45 connector
Support rubber Waterproof rubber
➃ Mount the waterproof nut from the rear end of the waterproof RJ45 connec\
tor, and tighten it.
Recommended tightening torque:
0.5 ~ 1.5 N∙m {0.37 ~ 1.11 lbf·ft}
Waterproof nut
Note:
• If a washer nozzle is used, prepare the washer nozzle mounting bracket (accessory) in advance,
and then install the washer nozzle and fix it while fixing the camera as\
described in Step 8 at the
same time.
• Please install the washer nozzle mounting bracket A with the “FRONT” mark facing the front of the camera (on the Panasonic logo side).
• After checking the installation, adjust the direction of the washer nozzle to ensure that the front glass is hit by water flow.
➀ Washer nozzle mounting bracket A
Applicable nozzle size: ø16 mm {5/8 inches} Washer hose
fixing holes × 4
Camera fixing
screws
× 4 (locally
procured)
FRONT
markWasher nozzle
mounting
bracket A
(accessory)Washer hose
(locally
procured)R4 mm {5/32 inches}
Handle
Protection bag
Fixing screws for the
washer nozzle mount-
ing bracket B
× 2 (accessory) Washer nozzle
Washer nozzle
mounting bracket A
(accessory)FRONTREAR➁Washer nozzle mounting bracket B
6 mm {1/4 inches}
Applicable
nozzle size Front view
IMPORTANT:
• Attach
the safety wire so that if the
camera were to become detached,
it would not fall on nearby people.
Washer nozzle mounting bracket B (accessory)
Safety wire fixing screws
(locally procured)
Safety wire
(accessory)
9
Step.6 If necessary, bend the camera’s tilt arm forward.
To shoot the foot area of the camera installed, change the settings of the tilt arm to an ap\
proximate 45°
incline. Please do as instructed below.
➀ Remove the 2 tilt arm fixing screws on the
left side of the camera.
• Loosen the support arm cover fixing screw
with an hex wrench (locally procured), and
remove the support arm cover from the
camera body.
• Remove the 2 tilt arm fixing screws from the
inside on the left.
Note:
• The removed support arm cover and the
2 screws will be reused after the tilt arm is
bent forward.
➁ Remove the 4 tilt arm fixing screws from
the right side of the camera.
• Loosen the 2 tilt cover cap fixing screws with
an hex wrench (locally procured), and remove
the tilt cover cap and the rubber cap from the
camera body.
• Remove the 4 tilt arm fixing screws from the
inside on the right.
Note:
• The removed tilt cover cap, the rubber
cap, and the 4 screws will be reused after
the tilt arm is bent forward.
➂ Ensure that the camera does not topple over, and bend the tilt arm
to an approximate 45° incline.
➃ Keep the TILT arm position tilted by an angle of 45°and re-fix the
screws and the covers removed in
➀ and ➁.
Tilt arm fixing screws: (Recommended tightening torque: 1.5 N∙m {1.11 lbf·ft})
Covers
: (Recommended tightening torque: 1.37 N∙m {1.01 lbf·ft})
Note:
• Repacking is impossible when the tilt arm is bent 45°. If the camera
needs to be moved from the preparation area to the installation
location, execute Step 6 in the vicinity of the installation location.
• Be sure to attach the rubber cap and the rubber washers on the
three fixing screws used to fix covers.
Support arm cover
Tilt arm fixing screws × 2
Support arm cover fixing
screwLeft side of the camera
Tilt arm fixing screws × 4
Rubber cap Tilt cover cap
Tilt cover cap fixing
screws × 2
Right side of the camera
* Pass the cable tie for fixing the washer hose through the washer nozzle mounting bracket A
first, and then, secure the washer nozzle
mounting bracket A together with the camera.