Panasonic Network Camera Bl-c210, Bl-c230 Setup Guide

							1. Insert the included CD-ROM into your PC.
• The Setup Program starts. If the program does not start, double-click Setup.exe found 
on the CD-ROM.
2. Click [Search for Cameras].
• The program searches for cameras connected to your network.
If [Windows cannot open this file] is displayed after clicking [Manual]
[Select the program from a list]→[OK]→Check [Always use the selected program to open this 
kind of file]→[Browse]→Browse to [C:\WINDOWS\system32\mshta.exe]→[Open]→[OK]
3. When the Windows Security Alert is displayed, click 
[Unblock].
4. For BL-C210A/BL-C230A Only:
If the camera is connected to a router, follow the 
procedure below and set [Network Settings] to 
[Automatic Setup].
1. Select the desired camera and click [Network Settings].
2. In the [Network Settings] screen, select [Automatic Setup], then click [Save].
• The camera restarts.
3. When [Camera setup completed] is displayed, click [OK].
4. Wait about one minute, then click [Begin Search].
5. Select the camera you want to configure, and click 
[Access Camera].
• To assign all network settings to the camera manually or to assign an IP address using 
the DHCP or the Automatic feature of your router, click [Network Settings], then select 
[Specify an IP Address], [DHCP] or [Automatic Setup] and enter the appropriate 
settings.
6. Enter the desired user name and password, then click 
[Save].
• Do not forget the user name and password you set here, otherwise you will need to 
reset the camera and configure it again.
7. Enter the user name and password, then click [OK].• When the user name and password dialog is displayed, enter the user name and 
password used in step 6, and then click [OK].
8. For BL-C230 Only:
Click [Next] to configure the camera’s wireless 
settings, enter the wireless settings, then click [Save].
• These settings are not available for the BL-C210, continue to the next step.
• If you are not using a wireless connection, select [Disable] and then click [NEXT] to 
skip this step. •[About this program]: Displays the program’s version 
information.
•[Search for Cameras]: Displays a list of cameras 
connected to your network.
•[Manual]: Allows you to view the included 
documentation. PDF versions of the printed 
documentation are included on the CD-ROM; Adobe
® 
Reader® is required to view them.
•[Update Firmware]: Allows you to use the Setup 
Program to update the camera’s firmware (built-in 
software).
•[Save Settings to PC/Save Settings to Camera]: 
Allows you to save a backup of all camera settings on 
your PC, or restore all settings in the camera using a 
backup file saved on your PC.
•[Network Camera Recorder with Viewer Software 
Single Camera Version Installation] / [Network 
Camera Recorder 16 Cameras Version 
Installation]: Installs the [Network Camera Recorder 
with Viewer Software Single Camera Version] / 
[Network Camera Recorder 16 Cameras Version] 
software. (See “Installing the Network Camera 
Recorder with Viewer Software Single Camera Version 
/ Network Camera Recorder 16 Cameras Version” on 
page 2.)
•[Exit]: Closes the screen and exits the Setup Program.
• If the dialog is not displayed, continue to the next step.
• If you have more than one camera, you can 
distinguish cameras by model number, 
printed on the front of the camera, or by 
MAC address (this refers to the MAC 
address label on the camera).
• If more than 20 minutes have passed since 
the selected camera was turned on, you 
cannot configure the camera. Turn off the 
camera, then turn it on again. This 
restriction does not apply to cameras which 
have not been configured yet or have been 
reset to their factory default settings.
• If you have more than one camera, you can 
distinguish cameras by model number, 
printed on the front of the camera, or by 
MAC address (this refers to the MAC 
address label on the camera).
• If more than 20 minutes have passed since 
the selected camera was turned on, you 
cannot configure the camera. Turn off the 
camera, then turn it on again. This 
restriction does not apply to cameras which 
have not been configured yet or have been 
reset to their factory default settings.
• If you are using firewall or antivirus software on your PC, the Setup Program may not 
be able to find any cameras on your network. If you cannot disable your firewall or 
antivirus software, you can configure the camera by entering its MAC address (this 
refers to the MAC address label on the camera).
If you are using a French, German, Italian, 
Spanish, Russian, Simplified Chinese, or 
Japanese language OS, this screen will be 
displayed in the corresponding language, 
and all subsequent camera screens will be 
displayed in that language. 
Access your wireless router and display its 
wireless settings. If your wireless router is 
not configured to use encryption, there is a 
risk of unauthorized access to your network 
and data. Enabling encryption is strongly 
recommended; WPA-PSK (TKIP) or WPA2-
PSK (AES) are particularly recommended 
(they are offer more security than WEP 
encryption). Note that when the router’s 
wireless settings are changed (including 
encryption settings), wireless network 
settings for all devices that connect to the 
router wirelessly must also be changed. For 
information on changing settings, refer to the 
operating instructions included with your 
wireless router and network devices. Match 
the camera’s wireless settings to the router’s 
settings. For more information, refer to:
• Operating instructions included with 
your wireless router
• 5.3.1 Configuring the Camera for 
Wireless Connection (BL-C230 Only) in 
the Operating Instructions on the CD-
ROM
• Panasonic Network Camera website
http://panasonic.net/pcc/support/netwkcam/
technic/wireless/cam_set.html
Before Reading this Document
This manual is written for both the BL-C210 (Wired Type) and BL-C230
(Wireless/Wired Type). Available features and operations vary slightly
depending on the model. You can confirm the model no. of your camera by
checking the model no. printed on the front of the camera.
Model number suffixes (“A”, “CE”, and “E”) are omitted from the following
model numbers shown in this document, unless necessary.
BL-C210A, BL-C210CE, BL-C210E, BL-C230A, BL-C230CE, BL-C230E
Make sure you have read the Important Information document and followed 
the instructions in the Installation Guide for connecting your camera.
• Before following the instructions in this document:
– Confirm that your camera is turned on and connected to your router.
– Temporarily disable any firewall or antivirus software on your PC.
– Close your web browser.
• Screenshots shown in this document are for reference only and may vary from what is 
displayed on your PC depending on the camera model, network settings, etc.
Abbreviations• UPnP is the abbreviation for “Universal Plug and Play”.
• The Network Camera is referred to as “the camera” in this document.
• The Setup CD-ROM is referred to as “the CD-ROM” in this document.
Trademarks
• Adobe and Reader are either registered trademarks or trademarks of Adobe Systems 
Incorporated in the United States and/or other countries.
• Microsoft, Windows, Windows Vista, Windows Server, ActiveX, and Internet Explorer are 
either registered trademarks or trademarks of Microsoft Corporation in the United States 
and/or other countries.
• Screen shots reprinted with permission from Microsoft Corporation.
• All other trademarks identified herein are the property of their respective owners.
• This software is based in part on the work of the Independent JPEG Group.
Setup Guide
Network Camera
Model No.BL-C210(Wired Type)
BL-C230(Wireless/Wired Type)
©   Panasonic System Networks Co., Ltd. 2009
PNQX1992YA   KK0809CQ2109
Please read this document before using the product, and save this document for future 
reference.
Panasonic Network Camera Website:
http://panasonic.net/pcc/ipcam/
Indoor Use Only 
						

							9. When [Setup completed] is displayed, click [To Single 
Camera page].
• If the following ActiveX® Controls dialog is displayed, click [Install ActiveX Control...].
• When the following Security Warning is displayed, click [Install].
• The camera image is displayed.
• Screen content varies by model number.
10. Click the [Setup] tab, click [Date and Time] on the left 
side of the screen, then set the camera’s date and 
time. Click [Save] when finished.
• Screen content varies by model number.
To configure the camera for access from the Internet or from a mobile 
phone, continue with the following steps.
Note:
• In order to configure the camera for access over the Internet using these instructions, your 
router must be UPnP™ compatible and must have its UPnP™ feature turned on (it is turned 
off by default on most routers). For more information, refer to the operating instructions 
included with your router.
• To configure the camera for access over the Internet using a router that does not support 
UPnP
™, refer to Section 4 Configuring the Camera for Access from the Internet in the 
Operating Instructions on the CD-ROM for general information, and refer to the operating 
instructions included with your router.
• Disable the maximum idle time setting on your router if you have a PPPoE or PPTP 
connection to your Internet Service Provider.
1. Click the [Internet] tab at the top of the camera screen.
2. Select [Enable] under [Auto Port Forwarding (IPv4)], 
select [Register with Viewnetcam.com] under 
[Viewnetcam.com Registration], then click [Save].
• When the dialog about the camera’s port number changing is displayed, click [OK].
• The camera and router will begin configuring themselves via UPnP™.
• If you select to register with Viewnetcam.com, click [Go to Viewnetcam.com 
Registration page] when it is displayed. The Viewnetcam.com website will open 
automatically. Follow the on-screen instructions to register.
3. When [Auto Port Forwarding setup is complete.] is 
displayed, click [To Single Camera page].
• If you enabled [Auto Port Forwarding (IPv4)], the camera’s port number may have 
changed. Do not forget the addresses displayed here.
• To confirm that the camera can be accessed from the Internet using a PC, use a PC 
not connected to your network and access the camera using the address displayed 
here.
• The IP address or URL used to access the camera over the Internet will also be 
displayed on the [Status] page of the [Maintenance] tab.
After configuring the camera’s wireless settings, confirm that the 
camera can be accessed wirelessly.
1. Disconnect the LAN cable from the camera, and 
unplug the AC adaptor from the power outlet.
3. Plug the AC adaptor in to the power outlet.
• Confirm that the indicator lights green after about 1 minute. If the indicator does not 
light green, see 1.2 POWER Indicator Issues in the Troubleshooting Guide on the CD-
ROM.
4. Start your web browser and access the camera.• Enter camera’s IP address that was displayed during setup, then press [Enter] on the 
keyboard.
• If you cannot access the camera, see 1.4 Wireless Connection Issues (BL-C230 Only) 
in the Troubleshooting Guide on the CD-ROM.
• You may need to restart your router in order to access the camera in wireless mode. The camera’s IP address is displayed. This is the 
IP address you must enter in your web browser to 
access the camera. Do not forget this address.
This will install the viewer program (ActiveX 
Controls) needed to display camera images 
properly. Viewer programs must be installed to
view H.264 images, MPEG-4 images, MJPEG
images, and to use audio features.
Congratulations! You have successfully set up the 
camera and can now view camera images.
For more information, refer to 5.5 Setting the Date 
and Time in the Operating Instructions on the CD-
ROM.
Setup is complete. To configure the camera for access from the 
Internet, see “Access from Internet Configuration”. To confirm the 
camera’s wireless connection (BL-C230 only), see “Confirming 
Wireless Connection (BL-C230 Only)”.
If you are finished setting up the camera, return to the Installation 
Guide and follow the instructions for mounting the camera.
Access from Internet Configuration
If you are interested in accessing your camera over 
the Internet, we recommend using 
Viewnetcam.com. Viewnetcam.com is a Dynamic 
DNS service designed for use with Panasonic 
Network Cameras, and is provided free of charge. 
For more information about Viewnetcam.com, 
refer to the Viewnetcam.com website
(http://www.viewnetcam.com) for information 
about this service.
The camera’s IP addresses for local (LAN) and 
Internet access are displayed. These are the IP 
addresses you must enter in your web browser to 
access the camera over the LAN or from the 
Internet. Do not forget these addresses.
Setup is complete. To confirm the camera’s wireless connection 
(BL-C230 only), see “Confirming Wireless Connection (BL-C230 
Only)”.
If you have any difficulty accessing the camera or viewing camera 
images, refer to the Troubleshooting Guide on the CD-ROM, 
otherwise return to the Installation Guide and follow the 
instructions for mounting the camera.
Confirming Wireless Connection (BL-C230 Only)
2. Set the WIRELESS/WIRED 
switch on the bottom of 
the camera to WIRELESS.
If you are finished setting up the camera, return to the Installation 
Guide and follow the instructions for mounting the camera.
Installing the Network Camera Recorder with Viewer Software Single Camera Version / Network Camera Recorder 16 
Cameras Version
The CD-ROM includes a single camera version of the Panasonic Network Camera Recorder with Viewer Software and a 16 cameras version of the Network Camera Recorder. Click [Manual] on 
the Network Camera Setup Program window for details about the installation and operation of these software.
1. Insert the included CD-ROM into your PC.• The Setup Program starts. If the program does not start, double-click Setup.exe found on the CD-ROM.
2. Click [Network Camera Recorder with Viewer Software Single Camera Version Installation] / [Network Camera Recorder 16 Cameras Ve r s i o n  
Installation].
3. Follow the on-screen instructions to install the software.
4. When installation is complete, double-click the shortcut icon (shown below) on your desktop to start the software.
Note:
• Network Camera Recorder with Viewer Software Single Camera Version is compatible with Microsoft® Windows Vista®, Windows® XP and Windows Server® 2003.
• Network Camera Recorder 16 Cameras Version is compatible with Microsoft® Windows® XP Professional Edition and Windows 2000 (Service Pack 2 or later).
•Network Camera Recorder with Viewer Software Single Camera Version: Camera registration is limited to one camera.
Network Camera Recorder 16 Cameras Version: Camera registration is limited to 16 cameras.
• Supports are not provided for the single camera version and the 16 cameras version of these software.
• The single camera version and the 16 cameras version software do not support H.264 images and MPEG-4 images. : Network Camera Recorder with Viewer Software Single Camera Version
: Network Camera Recorder 16 Cameras Version