Panasonic Kx Tg2740 Operating Instructions Manual

Installation
11
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Connecting the AC Adaptor
•USE ONLY WITH Panasonic AC ADAPTOR PQLV10 (Order No. PQLV10Z).
•The AC adaptor must remain connected at all times. (It is normal for the adaptor
to feel warm during use.)
•To connect a standard telephone on the same line, see page 102.
•If your unit is connected to a PBX which does not support Caller ID services, you
cannot access those services.
Hook
AC AdaptorPower Outlet (AC 120 V, 60 Hz) Fasten...

Installation
12
Connecting the Telephone Line Cord
Connect the telephone line cord(s) to the unit as follows.
To connect a two-line telephone jack
LINE 2 LINE 1/2
GREEN Plug
4-Wire Telephone
Line Cord 
with GREEN Plugs
Two-Line
Telephone Jack
(RJ14C) 

13
Preparation
For assistance, please call: 1-800-211-PANA(7262)
To connect two single-line telephone jacks
LINE 2 LINE 1/2
TRANSPARENT
Plug GREEN
Plug
Single-Line
Telephone Jacks
(RJ11C)
LINE 1
LINE 2
4-Wire Telephone Line Cord
with GREEN Plugs2-Wire Telephone Line Cord
with TRANSPARENT Plugs
If you use the unit as a single-line telephone only
LINE 2 LINE 1/2
TRANSPARENT Plug
Single-Line
Telephone Jack
(RJ11C)
LINE 1
2-Wire Telephone Line Cord
with TRANSPARENT Plugs 

Installation
14Battery strength
You can check the battery strength on the handset display.
The battery strength is as shown in the chart below.
Display promptBattery strength
Fully charged
Medium
Low
Needs to be recharged.
Discharged
Battery Charge
Place the handset on the base unit and charge for
about 15 hoursbefore initial use.
•The CHARGE indicator lights, a beep sounds and
“Charging” will be displayed on the handset. 
Installing the Battery in the Handset
Insert the battery into the handset as...

15
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Recharge
Recharge the battery when:
—
“Recharge battery” is displayed on 
the handset,
—“ ” flashes on the display, or
—
the handset beeps intermittently while it is in use.
•If you DO NOT recharge the handset battery for more than 15 minutes, the display
will continually indicate “Recharge battery” and/or “” will flash when the
handset is lifted off the base unit.
•If the battery has been discharged, the handset will display “Charge for...

Programmable Settings
16
Handset Programming Guidelines and Function Menu
The handset has programmable functions. Most of them are selected from
the function menu on the display (p. 17).
How to select a function item from the menu
Make sure the handset is not being used.
1. Press 
(CONF/FUNCTION). 
•The main menu is displayed (p. 17).
2. You can scroll through the menu by pressing
Öor Ñ. Scroll to the desired item by
pressing 
Öor Ñ.
3. Press 
áto select the item.
4. If the item has a sub-menu I, it will...

17
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Useful information:
•“---------------” indicates the beginning or end of the function menu.
•
You can go back to the previous display by pressing Üexcept when entering characters
or numbers. To return to the main menu from the sub-menu Ior sub-menu II, press Ü.
•You can exit the programming mode any time by pressing (OFF).
•If you do not press any buttons for 60 seconds, the handset will exit the
programming mode.
•If the unit detects a...

Programmable Settings
18
Base Unit Programming Guidelines and Function Menu
The base unit has programmable functions. Most of them are selected
from the function menu on the display (p. 19).
How to select a function item from the menu
Make sure the base unit is not being used.
1. Press 
(FUNCTION). 
•The main menu is displayed (p. 19).
2. You can scroll through the menu by pressing
Öor Ñ. Scroll to the desired item by
pressing 
Öor Ñ.
3. Press 
áto select the item.
4. If the item has a sub-menu I, it...

19
Preparation
For assistance, please call: 1-800-211-PANA(7262) •
You can go back to the previous display by pressing Üexcept when entering characters
or numbers. To return to the main menu from the sub-menu Ior sub-menu II, press Ü.
•You can exit the programming mode any time by pressing (STOP/EXIT).
•If you do not press any buttons for 60 seconds, the base unit will exit the
programming mode.
•If the unit detects a problem, an error message will be displayed (p. 106).
Base unit function menu table
You...

Programmable Settings
20
Date and Time
Voice Day/Time Stamp:During playback, a synthesized voice will
announce the day and time that each message was recorded.
Use the base unit. Make sure the base unit is not being used.
1
Press (FUNCTION).
2
Scroll to “Date and time” by pressing Ö
or Ñ.
3
Press á.
4
#Enter the year, and month and day using
4-digit numbers. (Ex. To set Apr. 7, 2002,
enter “2002” and “0407”.)
$Enter the time (hour and minute) using 
a 4-digit number. (Ex. To set 9:30, enter
“0930”.)
•If...