Panasonic Kx P7305 Operating Instructions Manual

Cleaning the Printer
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.9
3While rotating the pick up roller, wipe it with a soft cloth that has been 
moistened with a mild commercial cleaner.
4Open the front cover.
5Lift the drum unit up (1) and slide it out of the printer (2).
•To avoid possible toner spillage, it is recommended to place the drum unit on a
newspaper or drop cloth.
Pick up roller
1
2
1 

Cleaning the Printer
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.10
SAFETY CAUTION
•It is very hot inside the printer; to avoid personal injury, do not touch the components 
illustrated below.
CAUTION
• To prevent any damage to the drum unit, observe the following precautions.
— Do not touch the drum surface illustrated below. 
— Do not expose the drum unit to light for more than 5 minutes.
— Do not expose the drum unit to direct sunlight.
— Do not keep the drum unit near...

Cleaning the Printer
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.11
6Wipe rollers (A) and (B), and paper chute with a soft cloth that has been 
moistened with a mild commercial cleaner.
•Be sure to remove the paper dust.
NOTE
• Front rollers (A) can be rotated half. Inner rollers (B) can be rotated to the direction of the 
arrow. Be sure not to damage the sheets in front of the inner rollers (B).
7Turn the sponge up and carefully wipe the laser unit cover glass with a 
dry...

Cleaning the Printer
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.12
8Carefully wipe the corona wire of the drum unit by sliding a dry cotton 
swab from end to end a few times.
9Firmly insert the drum unit in the slot of the printer (1) [insert the side pins 
of the drum unit into the groove (label  )]. Push down (2). 
10Close the front cover and replace the media tray into the printer.
corona wire
2
2
1
Side pin 

Clearing a Jam
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.13
If the printer has frequent media jams, make sure that you follow these guidelines:
• Always use high-quality paper and transparencies (see “Media” on page 53).
• Make sure that you load thick paper [106 – 165 g/m
2 (29 – 44 lb.)] or labels only in the 
manual feed.
If a media jam occurs, the printer status display reports “Jam at ”. The  
are the various sensors throughout the paper path as illustrated below....

Clearing a Jam
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.14
When a media feed error has occurred, clear the media feed error as follows:
1Pull the media tray out of the printer or 2nd feeder (option).
2Tap the media stack on a level surface to avoid media jams or skewed 
printing.
•If a media feed error has occurred, remove the media stack from the media tray and
tap it.
Jam at STD / Jam at OP 

Clearing a Jam
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.15
3Place the media with the print side down.
•Be sure that the media does not exceed the limit mark.
NOTE
• If the metal plate is in the up position by accident, the media tray cannot be inserted into the 
printer. Before loading the media, push down the metal plate until it clicks, locking it in place.
4Replace the media tray into the printer or 2nd feeder (option).
CAUTION
• Be sure to hold the media tray with both...

Clearing a Jam
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.16
5Open and close the front cover to clear the error indication.
2
1 

Clearing a Jam
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.17
1Open the front cover.
2Lift the drum unit up.
Jam at A 

Clearing a Jam
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.18
3Grasp both sides of the jammed media and slowly pull it out of the 
printer.
4Push the drum unit down.
5Close the front cover.