Panasonic Dmp Bdt500 Owners Manual

							Settings
31VQT3V91
∫Easy Network Setting (> 14)
∫Network Settings
Perform network-related settings individually.
Tap to show the following settings:
¾ LAN Connection Mode
Select the LAN connection method.
≥ Select “Wireless Master” when you make a 
direct wireless connection between this unit 
and a Home Network device. Internet 
connection is not availabl e when this item is 
selected.
¾ Wireless Settings
This allows the wireless router and connection 
settings to be set. Current connection settings 
and connection state can be checked.
Connection Setting
The wireless router connection wizard will be 
displayed.
Double Speed Mode Setting (2.4GHz)
When a 2.4 GHz wireless format is used, this 
sets the connection speed.
≥ If you connect using the “Double Speed 
Mode (40MHz)”, 2 channels use the same 
frequency band, and there is consequently 
a greater risk of reception interference. This 
can cause the connecti on speed to drop or 
become unstable.
¾ IP Address/DNS Settings
This is for checking the state of the network 
connection and setting the IP address and 
DNS-related.
Tap to show the respective setting.
¾ Proxy Server Settings
This is for checking the state of connection with 
the Proxy server and performing settings.
Tap to show the respective setting.
¾ Network Service Settings ( >22) 
(VIERA Connect)
Tap to show the following settings:
Audio Auto Gain Control
Volume that is different depending on the 
contents is adjusted aut omatically to the 
standard volume while using the VIERA 
Connect.
≥ Depending on contents, this function effect 
will not work.
≥ Select “Off” when t he audio is distorted.
Time Zone
By selecting the time zone, it is possible to set 
the unit’s time to match your location.
≥Some VIERA Connect contents require the 
time zone to be set. Set the time zone if 
necessary.
DST
Select “On” when using Daylight Saving time.
¾Network Drive Connection
It is possible to access the shared folder of 
equipment not compatible with DLNA, such as 
the Windows XP operating system, and play 
back video, still pictures, and music on this unit.
For the setting and operation method of 
connected equipment, refer to the following 
website. 
http://panasonic.jp/support/global/cs/
(This site is in English only.)
¾ Remote Device Settings ( >23)
Tap to show the following settings:
Remote Device Operation
Enable to operate by DMC.
≥ If “On” is selected, “Quick Start” will be 
activated.
Setting Unit Name
Set the name of this unit to be displayed on 
the connected equipment.
Network
DMP-BDT500_VQT3V91_eng.book  31 ページ  ２０１２年２月１４日　火曜日　午後１時９分 
						

							32VQT3V91
Registration Type
Remote Device List
Registering/deregistering of the displayed 
equipment can be performed when “Manual” 
in “Registration Type” is selected.
¾BD-Live Internet Access ( >21)
You can restrict Internet access when BD-Live 
functions are used.
≥ If “Allow (Limited)” is selected, Internet 
access is permitted only for BD-Live contents 
which have content owner certificates.
The following items use the same password.
Don’t forget your password.
∫ DVD-Video Ratings
Set a ratings level to limit DVD-Video play.
∫ BD-Video Ratings
Set an age limit of BD-Video play.
∫ Network Service Lock
You can restrict the usage of VIERA Connect.
∫ Easy Setting
You can execute basic settings. 
∫ Display Settings
Tap to show the following settings:
¾ TV Aspect
Set to match the type of television connected.
When connected to a 4:3 aspect television and 
playing 16:9 ratio image:
When connected to a 16:9 widescreen 
television and playing 4:3 ratio image:
¾ Screen Saver Function
This is to prevent burn-in on the screen.
≥ When this is set to “On”:
If a list of playback content is displayed and 
there is no operation for 10 minutes or more, 
the screen switches to HOME menu 
automatically.
≥ While playing and pausing, etc., this function 
is not available.
¾Status Messages
Choose whether to show status messages 
automatically.
Auto
Allow connection to all the 
equipment that is accessing 
this unit.
Manual
Set the permission of the 
connection individually for the 
equipment that is accessing 
this unit.
Ratings
System
4:3 Pan & 
Scan
The sides are cut 
off so the picture 
fills the screen. 
When playing 
BD-Video, video is output as “4:3 
Letterbox”.
4:3 
LetterboxBlack bands 
appear at the top 
and bottom of the 
picture.
16:9Video is displayed as a 4:3 ratio 
image in the center of the screen.
16:9 FullVideo is displayed as a 
horizontally stretched 16:9 
image.
DMP-BDT500_VQT3V91_eng.book  32 ページ  ２０１２年２月１４日　火曜日　午後１時９分 
						

							Settings
33VQT3V91
¾VIERA Link
Set to use “HDAVI Control” function when 
connected via HDMI cable to a device that 
supports “HDAVI Control”.
≥ Select “Off” when you do not want to use 
“HDAVI Control”.
∫ Unit Settings
Tap to show the following settings:
¾ Front Panel Display
Changes the brightness of the unit’s display.
≥ If “Auto” is selected, the display is set to bright 
and only dimmed during playback.
¾HDMI(SUB) V.OFF LED Control
Set to light the HDMI (SUB) V.OFF LED or not.
≥ This will light when “HDMI(SUB) Output 
Mode” is set to “V.OFF”, and the power of the 
connected equipment to the HDMI AV OUT 
SUB is on.
¾Unit Operation Sound
Set the volume of operation of this unit.
¾ Edit User Information
Change the user information registered in the 
Home menu.
∫ Quick Start
Speed of startup from power off is increased.
≥ When set to “On”, the internal control unit will be 
powered and the idle power consumption will 
increase compared to when set to “Off”. (About 
the power consumption  >39)
∫ Remote Control Code
Change the remote control code if other 
Panasonic products react to this remote control.
∫ Touchpad Guide
Show the operation guide for the touchpad.
∫ Firmware Update ( >16)
Tap to show the following settings:
¾ Automatic Update Check
When this equipment remains connected to the 
Internet, it will check for the latest firmware 
version when it is turned on and you can update 
it if necessary.
¾ Update Now
You can update the firmware manually if a 
firmware update is available.
∫ System Information
Tap to show the following settings:
¾ License
Information about the software used by this unit 
is displayed.
¾ Firmware Version Information
Display firmware version of this unit and 
wireless LAN module.
∫ DivX Registration  [For_Canada]
You need this registration code to purchase and 
play DivX Video-on-Demand (VOD) content.
∫ Restore Default Settings
This returns all values in the Setup menu and the 
Option menu to the default settings, except for 
some settings of network, ratings, remote control 
code, language, etc.
DMP-BDT500_VQT3V91_eng.book  33 ページ  ２０１２年２月１４日　火曜日　午後１時９分 
						

							34VQT3V91
ReferenceTroubleshooting guide
Before requesting service, please perform the 
following steps.
The following do not indicate a problem with 
this unit:
– Regular disc rotating sounds.
– Image disturbance during search.
– Image disturbance when replacing 3D discs.
∫Unit doesn’t respond to remote 
control or front panel buttons.
Touch and hold [ Í/I] on the main unit for 
3 seconds.
– If still unable to power the unit off, disconnect  the power cord, wait 1 minute, then reconnect 
the power cord.
∫ Cannot eject disc.
The unit may have a problem.
1 While the unit is off, press and hold [KEYS], 
[B] and [Y] on the remote control at the same 
time for more than 5 seconds.
– “00 RET” is displayed on the unit’s display.
2 Press [R] repeatedly on the remote control 
until “06 FTO” is displayed on the unit’s 
display.
3 Press [G] on the remote control. To return to the factory preset.
¾
Select “Yes” in “Restore Default Settings” in 
the Setup menu. ( >33)
To return all settings to the factory preset.
¾ Reset the unit as follows:
1 While the unit is off, press and hold [KEYS], 
[B] and [Y] on the remote control at the same 
time for more than 5 seconds.
– “00 RET” is displayed on the unit’s display.
2 Press [R] repeatedly on the remote control 
until “08 FIN” is displayed on the unit’s 
display.
3 Press and hold [G] on the remote control at 
least 3 seconds.
This unit is turned off when the input for the 
TV is switched.
¾
This is a normal phenomenon when using VIERA 
Link (HDAVI Control 4 or later). For details please 
read the operating instructions for the TV.
The remote control doesn’t work properly.
¾
Change the batteries in the remote control. (>4)
¾The remote control and main unit are using 
different codes. If “SET  ” is displayed on the 
unit’s display when a button is pressed on the 
remote control, change the code on the 
remote control. ( >33, 37)
The TV tuner mode is not displayed when the 
TV is switched on.
¾
This phenomenon may occur, depending on the 
TV setting, when “Quick Start” is set to “On”.
¾ Depending on the TV, this phenomenon may 
be prevented by reconnecting the HDMI cable 
to a different HDMI input terminal or by 
changing the HDMI auto connection setting.
You have forgotten your ratings password.
You want to cancel the ratings level.
¾The ratings level returns to the factory preset.
1 While the unit is on, press and hold [KEYS], 
[B] and [Y] on the remote control at the same 
time for more than 5 seconds.
– “00 RET” is displayed on the unit’s display.
2 Press [R] repeatedly on the remote control 
until “03 VL” is displayed on the unit’s display.
3 Press [G] on the remote control.
Do you have the latest firmware installed?
Firmware updates may be released to correct 
operating irregularities that are discovered 
with certain movies. ( >16)
4
Make the following checks and visit our 
website for more information.
For U.S.A.  : 
www.panasonic.com/help
Enter the model number.
For Canada  : 
http://www.panasonic.ca
4
Or visit our website to find a service 
center.
You can find a service c enter near you easily 
on our website.
Other support information :
“Customer Services Directory (United States 
and Puerto Rico)” ( >44) or “Limited 
Warranty (Only for CANADA)” ( >45).
General operation
DMP-BDT500_VQT3V91_eng.book  34 ページ  ２０１２年２月１４日　火曜日　午後１時９分 
						

							Reference
35VQT3V91
This unit does not recognize the USB 
connection correctly.
¾Disconnect and reconnect the USB cable. If it 
still does not recognize the connection, turn 
the power of this unit off and on again.
¾ USB devices may not be recognized by this 
unit when connected using the following:
–a USB hub
– a USB extension cable
¾ If you connect USB HDD to this unit, use the 
USB cable that is supplied with the HDD.
The buttons of the unit do not work.
¾Touch the buttons with your finger. They may 
not work if operated with your fingernails or 
hands wearing gloves.
The images from this unit do not appear on 
the television.
Picture is distorted.
¾An incorrect resolution is selected in “HDMI 
Resolution”. Reset the setting as follows:
1 While the unit is on, press and hold [KEYS], 
[B] and [Y] on the remote control at the same 
time for more than 5 seconds.
– “00 RET” is displayed on the unit’s display.
2 Press [R] repeatedly on the remote control 
until “04 PRG” is displayed on the unit’s 
display.
3 Press and hold [G] on the remote control for 
at least 3 seconds.
Set the item again. ( >28)
– When Dolby Digital Plus, Dolby TrueHD,  and DTS-HD audio are not output in 
bitstream, select “Yes” in “Restore Default 
Settings” and make proper settings. ( >33)
¾ When “3D BD-Video Playback” in the Setup 
menu is set to “Auto”, images may not be 
output depending on the connection method. 
After removing the disc from this unit, select 
“Set before play” in the Setup menu, and 
select “2D Playback” in the setup screen 
displayed when playing 3D discs. ( >30)
Video is not output.
¾
Set “High Clarity Sound” in the Setup menu to 
“Disable” to use the VIDEO OUT terminal. (>30)
¾ Video from the HDMI AV OUT SUB terminal is 
not output when the “HDMI(SUB) Output 
Mode” is set to “V.OFF”. ( >28)
Video is not output in high-definition.
¾ Confirm that “HDMI Resolution” in the Setup 
menu is set properly. ( >28)
3D video is not output.
¾ Change the settings as required by the 
connected TV format. ( >30, “3D Type”)
¾
Is there a non-3D compatible amplifier/receiver 
connected between this unit and a TV? (
>11 )¾ If there is a non-3D compatible amplifier/
receiver connected to the HDMI AV OUT SUB 
terminal, set the “HDMI(SUB) Output Mode” 
to “V.OFF”. ( >11 )
¾ Are the settings on this unit and the TV 
correct? ( >21)
¾ Is the amplifier/receiver that is connected 
between this unit and TV on?
¾ Depending on the connected TV, the video 
being played back might switch to 2D video 
due to changes in resolution etc. Check the 
3D setting on the TV.
3D video is not output correctly as 2D.
¾Select “Set before play” in the Setup menu, 
and select “2D Playback” in the setup screen 
displayed when playing 3D discs. ( >30, “3D 
BD-Video Playback”)
¾ Discs that have recorded titles with Side by 
side (2 screen structure) and that can be 
enjoyed in 3D are played back in accordance 
with the settings of the TV.
No subtitles.
¾When progressive output is on, closed 
captions/subtitles cannot be displayed.
The subtitles overlap closed captions 
recorded on discs.
¾Turn off the subtitles or the closed caption 
setting on the TV.  ( > 25)
A black band is displayed around the edge of 
the screen.
The aspect ratio of the screen is abnormal.
¾
Confirm the “TV Aspect” is set properly. (>32)
¾ Adjust the aspect setting on the television.
Picture
DMP-BDT500_VQT3V91_eng.book  35 ページ  ２０１２年２月１４日　火曜日　午後１時９分 
						

							36VQT3V91
Cannot switch audio.
¾When connecting an amplifier/receiver using 
DIGITAL AUDIO OUT or HDMI AV OUT 
terminal, you cannot switch the audio if 
“Digital Audio Output” is set to “Bitstream”. 
Set “Digital Audio Output” to “PCM”. ( >29)
Cannot hear the desired audio type.
¾ Check the connections and the “Digital Audio 
Output” settings. ( >11, 29)
¾ When the unit is connected to an amplifier/
receiver with the AUDIO OUT terminals, set 
“Analog Audio Output”. ( >30)
¾ To output audio from a device connected with 
an HDMI cable, set “HDMI Audio Output” to 
“On” in the Setup menu. ( >29)
¾
When connecting this unit to a TV via an 
HDMI AV OUT MAIN and to an amplifier/
receiver via an HDMI AV OUT SUB, set 
“HDMI(SUB) Output Mode” to “V.OFF”. (
>11 )
There is no sound coming out from the TV. 
¾ Audio may not output from the TV when the 
amplifier/receiver is connected to the HDMI 
AV OUT SUB, and “HDMI(SUB) Output 
Mode” ( >28) is set to “V.OFF”. In such a 
case, output audio from the amplifier/receiver. 
To output audio from the TV, set the 
“HDMI(SUB) Output Mode” to “Normal”.
Disc cannot be played.
¾ The disc is dirty. ( >4)
Still pictures (JPEG) do not play back normally.
¾ The images that were edited on the PC, such 
as Progressive JPEG, etc., may not be played 
back.
I can’t play back BD-Live.
¾The SD card is write-protected. ( >6)
¾ Confirm that this unit is connected to the 
broadband Internet. ( >13)
¾ Confirm the “BD-Live Internet Access” 
settings. ( >32)
¾ Confirm an SD card is inserted into the SD 
card slot. ( >17)
I can’t connect to the network.
¾ Confirm the network connection and settings. 
(>13, 14, 31)
¾ Check the operating instructions for each 
device and connect accordingly.
When using wireless LAN connection, video 
from the DLNA Certified media server is not 
played back or video frames are dropped 
during playback.
¾Higher transfer rate router such as 802.11n 
(2.4 GHz) wireless router may solve the 
problem. If you use 802.11n (2.4 GHz) 
wireless router, it is necessary to set the 
encryption type to “AES”.
Simultaneous use with a microwave, cordless 
telephone etc. at 2.4 GHz may result in 
connection interruptions or other problems.
¾ On the “Wireless Settings” screen ( >31), the 
continuous lighting of at least 4 “Reception” 
indicators is the target for a stable connection. 
If 3 or fewer indicators are lit or the 
connection is being interrupted, change the 
position or angle of your wireless router and 
see if the connection state improves. If there 
is no improvement, connect to a wired 
network and perform the “Easy Network 
Setting” ( >14) again.
Audio
Playback
Network
DMP-BDT500_VQT3V91_eng.book  36 ページ  ２０１２年２月１４日　火曜日　午後１時９分 
						

							Reference
37VQT3V91
Messages
The following messages or service numbers 
appear on the television or unit’s display.
Cannot play.
¾You inserted an incompatible disc (Discs 
recorded in PAL video, etc.).
Cannot display on this unit.
¾You tried to play a non-compatible image.
¾ Confirm “SD” on the unit’s display is not 
displayed and re-insert the card.
No disc inserted.
¾The disc may be upside down.
$ This operation is not available.
¾ Some operations are unsupported by the unit. 
For example;
– BD-Video: During playback, reverse slow 
motion or reverse frame-by-frame is not 
possible.
IP address is not set.
¾ The “IP Address” in “IP Address/DNS 
Settings” is “---. ---. ---. ---”. Set the “IP 
Address”, “Subnet Mask”, and “Default 
Gateway”. (Select the automatic address 
acquisition if necessary.)
The current wireless network security setting 
is weak. It is recommended to change to a 
stronger security setting.
¾Authentication type for the wireless LAN is set 
to “Open system”, or the encryption type is 
set to “No encryption”. It is recommended to 
encrypt for safety reasons. For details, refer 
to the instructions of the wireless router being 
used. Encryption is required when playing 
back video, etc., from DLNA compatible 
devices.
F99
¾The unit fails to operate properly. Press [ Í/I] 
on the main unit for 3 seconds to switch the 
unit to standby, then switch back on.
HDMI ONLY
¾ Some BD-Video discs can only be output with 
HDMI.
NET
¾While connecting to a network.
No PLAY
¾There is a viewing restriction on a BD-Video 
or DVD-Video. ( >32)
No READ
¾ The media is dirty or badly scratched. The 
unit cannot play.
PLEASE WAIT
¾The unit is carrying out an internal process. 
This is not a malfunction. You cannot operate 
the unit while “PLEASE WAIT” is displayed.
REMOVE
¾The USB device is drawing too much power. 
Remove the USB device.
SET   (“    ” stands for a number.)
¾ The remote control and main unit are using 
different codes. Change the code on the 
remote control.
Press and hold [OPTION] and the following 
button at the same time for more than 
5 seconds depending on the indication.
SET 1: [G]
SET 2: [B]
SET 3: [Y]
U59
¾The unit is hot.
The unit switches to standby for safety 
reasons. Wait for about 30 minutes until the 
message disappears.
Select a position with good ventilation when 
installing the unit.
On the television
On the unit’s display
DMP-BDT500_VQT3V91_eng.book  37 ページ  ２０１２年２月１４日　火曜日　午後１時９分 
						

							38VQT3V91
H or F 
(“  ” stands for a number.)
¾ There is something unusual.
¾ Check the unit using the troubleshooting 
guide. If the service number remains 
displayed, do the following.
1 Disconnect the plug from the AC outlet, wait a 
few seconds, then reconnect it.
2 Press [ Í/I] to turn the power on.
If the service number remains displayed despite 
doing the above, request service from the dealer. 
Inform the dealer of the service number when 
requesting service.
START
¾ The system is being restarted during the 
firmware update. Please do not turn off the 
unit.
UPD /
(“  ” stands for a number.)
¾ The firmware is being updated.
Please do not turn off the unit.
FINISH
¾The firmware update is complete.
Supplemental 
infor mation
∫Display languages list
∫ Language code list
DisplayLanguageDisplayLanguageDisplayLanguage
LanguageCodeLanguageCodeLanguageCode
ENG
FRA
DEU
ITA
ESP
NLD
SVE
NOR
DAN
POR
RUS English
French
German
Italian
Spanish
Dutch
Swedish
Norwegian
Danish
Portuguese
Russian ARA  
HIN
PER
IND
MRI
BUL
RUM
GRE
TUR 
JPN
CHI
KOR
MAL
VIE
THA
POL
CES
SLK
HUN
FIN Japanese
Chinese
Korean
Malay
Vietnamese
Thai
Polish
Czech
Slovak
Hungarian
FinnishArabic
Hindi
Persian
Indonesian
Maori
Bulgarian
Romanian
Greek
Turkish
Others
Abkhazian: 6566
Afar: 6565
Afrikaans: 6570
Albanian: 8381
Amharic
:6577
Arabic: 6582
Armenian: 7289
Assamese: 6583
Aymara: 6589
Azerbaijani: 6590
Bashkir: 6665
Basque: 6985
Bengali; Bangla: 6678
Bhutani: 6890
Bihari: 6672
Breton: 6682
Bulgarian: 6671
Burmese: 7789
Byelorussian: 6669
Cambodian: 7577
Catalan: 6765
Chinese: 9072
Corsican: 6779
Croatian: 7282
Czech: 6783
Danish: 6865
Dutch: 7876
English: 6978
Esperanto: 6979
Estonian: 6984
Faroese: 7079
Fiji: 7074
Finnish: 7073
French: 7082
Frisian: 7089
Galician: 7176
Georgian: 7565
German: 6869
Greek: 6976
Greenlandic: 7576
Guarani: 7178 Gujarati: 7185
Hausa: 7265
Hebrew: 7387
Hindi: 7273
Hungarian: 7285
Icelandic: 7383
Indonesian: 7378
Interlingua: 7365
Irish:
7165
Italian: 7384
Japanese: 7465
Javanese: 7487
Kannada: 7578
Kashmiri: 7583
Kazakh: 7575
Kirghiz: 7589
Korean: 7579
Kurdish: 7585
Laotian: 7679
Latin: 7665
Latvian, Lettish: 7686
Lingala: 7678
Lithuanian: 7684
Macedonian: 7775
Malagasy: 7771
Malay: 7783
Malayalam: 7776
Maltese: 7784
Maori: 7773
Marathi: 7782
Moldavian: 7779
Mongolian: 7778
Nauru: 7865
Nepali: 7869
Norwegian: 7879
Oriya: 7982
Pashto, Pushto: 8083
Persian: 7065
Polish: 8076
Portuguese: 8084
Punjabi: 8065
Quechua: 8185 Rhaeto-Romance:
8277
Romanian: 8279
Russian: 8285
Samoan: 8377
Sanskrit: 8365
Scots Gaelic: 7168
Serbian: 8382
Serbo-Croatian: 8372
Shona: 8378
Sindhi: 8368
Singhalese: 8373
Slovak: 8375
Slovenian: 8376
Somali: 8379
Spanish: 6983
Sundanese: 8385
Swahili: 8387
Swedish: 8386
Tagalog: 8476
Tajik: 8471
Tamil: 8465
Tatar: 8484
Telugu: 8469
Thai: 8472
Tibetan: 6679
Tigrinya: 8473
Tonga: 8479
Turkish: 8482
Turkmen: 8475
Twi: 8487
Ukrainian: 8575
Urdu: 8582
Uzbek: 8590
Vietnamese: 8673
Volapük: 8679
Welsh: 6789
Wolof: 8779
Xhosa: 8872
Yiddish: 7473
Yo r u b a : 8 9 7 9
Zulu: 9085
DMP-BDT500_VQT3V91_eng.book  38 ページ  ２０１２年２月１４日　火曜日　午後１時９分 
						

							Reference
39VQT3V91
Precautions of Wireless 
LAN connection
The following limits are in place regarding the 
usage of this unit. You must be aware of these 
limits before using this unit.
Panasonic will in no way be responsible for any 
incidental damage which may arise due to a 
failure to obey these limits, or to any condition of 
use or disuse of this unit.
≥Data transmitted and received over radio 
waves may be intercepted and monitored.
≥ This unit contains delicate electronic 
components.
Please use this unit in the manner in which it 
was intended and follow the following points:
– Do not expose this unit to high temperatures 
or direct sunlight.
– Do not bend, or subject this unit to strong 
impacts.
– Keep this unit away from moisture.
– Do not disassemble or alter this unit in any way.
Specifications
≥ Specifications are subject to change without notice.
(Continued on the next page.)
Signal system NTSC
Operating 
temperature rangei
5 oC to  i35  oC 
( i 41  oF to  i95  oF)
Operating humidity 
range  10 % to 80 % RH 
(no condensation)
Video output
Output level: 1.0 Vp-p (75 ≠)
Output connector: 
Pin jack (1 system)
Audio outputOutput level: 2 Vrms (1 kHz, 0 dB)Output connector: Pin jack
Number of connectors:
7.1 channel discrete output
1 system
(2 channel + 5.1 channel 
discrete output)
Digital audio output Optical digital output 
(Optical terminal)
Coaxial digital output 
(Pin jack)
HDMI AV outputOutput connector: 
Type A (19 pin) 2 system
SD card slot1 system
USB slotUSB2.0
2 system
Ethernet10BASE-T/100BASE-TX 
1 system
Wireless LAN Standard Compliance: 
IEEE802.11 b/g/n
Frequency range:
2.4 GHz band
Security: 
WPA
TM/WPA2TM 
(Encryption Type: TKIP/AES, Authentication Type: PSK), WEP (64 bit/128 bit)
LASER Specification Class  I LASER Product
Wave length:  790 nm (CDs)/
660 nm (DVDs)/405 nm (BDs)
Laser power:  No hazardous 
radiation is emitted with the 
safety protection
Power supply AC 120 V, 60 Hz
Power consumptionApprox. 11 W
Power consumption 
in standby modeApprox. 0.1 W
Power consumption 
in quick start 
standby modeApprox. 4.5 W
Dimensions 
(W
kHk D)
Including the 
projecting parts 430 mm
k59 mm k245 mm
(Approx. 16 15/16 zk2 3/8zk
9 11/16 z)
Mass (Weight) Approx. 2.6 kg (5.72 lbs)
DMP-BDT500_VQT3V91_eng.book  39 ページ  ２０１２年２月１４日　火曜日　午後１時９分 
						

							40VQT3V91
≥With certain recording states and folder structures, the play 
order may differ or playback may not be possible.
The audio output differs depending on which 
terminals are connected to the amplifier/receiver, 
and the settings on the unit. ( >29, Digital Audio 
Output)
≥ The number of channels listed is the maximum possible 
number of output channels  when connected to amplifier/
receiver compatible with the respective audio format.
HDMI AV OUT/
DIGITAL AUDIO OUT (Coaxial/Optical)
AUDIO OUT
*1When “BD-Video Secondary Audio” is set to “On”, the audio will 
be output as Dolby Digital, DTS Digital Surround or 5.1ch PCM.
*2The audio output is amplified from 5.1ch or 6.1ch to 7.1ch 
depending on the DTS, Inc. specifications.
File format
File formatExtensionReference
MP3 “.MP3”, “.mp3”
This unit supports ID3 tags, 
but only titles, artist names 
and album names can be 
displayed.
JPEG “.JPG”, “.jpg”
≥MOTION JPEG and 
Progressive JPEG are 
not supported
≥ You may not be able to 
play back the file if you 
have edited the folder 
structure or the file name 
on a PC or other device.
DivX[For_Canada]
“.DIVX”, “.divx”, 
“.AVI”, “.avi”≥The video file and 
subtitles text file are 
inside the same folder, 
and the file names are 
the same except for the 
file extensions.
≥ Some DivX
 [For_Canada] and MKV 
file may not be played 
back, depending on the 
video resolution and 
frame rate condition.
Subtitles text 
file
“.SRT”, “.srt”, 
“.SUB”, “.sub”, 
“.TXT”, “.txt”
MKV “.MKV”, “.mkv”
Subtitles text 
file
“.SRT”, “.srt”, 
“.SSA”, “.ssa”, 
“.ASS”, “.ass”
FLAC
“.flac”Maximum sampling rate:
192 kHz/24 bit
WAV“.wav”Maximum sampling rate:
48 kHz/16 bit
MPO “.mpo”3D still picture
Audio infor mation
Te r m i n a l“Digital Audio Output”
“Bitstream”“PCM”
HDMI AV 
OUT Outputs using 
original audio*1BD-Video : 7.1ch PCM*1*2
DVD-Video : 5.1ch PCM
DIGITAL 
AUDIO 
OUT Dolby Digital/
DTS Digital 
Surround
Down-mixed 2ch PCM
7.1ch AUDIO OUT
BD-Video : 7.1ch*1*2
DVD-Video : 5.1ch
5.1ch AUDIO OUT
5.1ch
2 ch AUDIO OUT2ch
Restriction on use of 
unauthorized copied content
This unit adopts the following technology for 
copyright protection.
Cinavia Notice 
This product uses Cinavia technology to limit 
the use of unauthorized copies of some 
commercially-produced film and videos and 
their soundtracks. When a prohibited use of an 
unauthorized copy is detected, a message will 
be displayed and playback or copying will be 
interrupted. 
More information about Cinavia technology is 
provided at the Cinavia Online Consumer 
Information Center at http://www.cinavia.com.
 
To request additional information about Cinavia 
by mail, send a postcard with your mailing 
address to: 
Cinavia Consumer Information Center, P.O. 
Box 86851, San Diego, CA, 92138, USA. 
DMP-BDT500_VQT3V91_eng.book  40 ページ  ２０１２年２月１４日　火曜日　午後１時９分