Panasonic Color Cctv Camera Wv Cs564 Operating Instructions
Here you can view all the pages of manual Panasonic Color Cctv Camera Wv Cs564 Operating Instructions. The Panasonic manuals for Camera are available online for free. You can easily download all the documents as PDF.
Page 41
43 • The following steps of installation and connection should be taken by qualified service personnel or system installers and should conform to all local codes. • Make sure to switch the camera off before installation and connection. • Do not install the camera near the air outlet of an air conditioner. Camera mounting base Camera Camera mounting base Fixing screw Loosen and push 1234 ON1234 ON5678 SW 1 SW 2 INSTALLATION 1. Disassembling the Camera (1) Loosen the fixing screw to separate the camera...
Page 42
44 Unit Number Switch 1, an 8-bit DIP switch, specifies unit number or returns to the factory default settings for Panasonic’s protocol. When the switch position corresponding to the unit number 1-96* is selected, setting should be made on the RS485 SET UP menu (see page 40). 1234 ON5678 SW 1 For Panasonic’s Protocol 1234 ON5678 Switch positionUnit number 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234...
Page 43
45 1234 ON5678 Switch positionUnit number 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 Switch positionUnit numberSwitch positionUnit number 69 70 71 72 73 74 75 76 7778 79 80 81 82 83 84 85 8687 88 89 90 91 92 93 94 951234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678
Page 44
46 Full duplex (4 line) * BP 2 BP 1 Function Switch position Function Switch position RS485 Setting The 4-bit DIP switch in used for RS485 termination. ON Marking 1. Mark the mounting holes on the ceiling, using the removed camera mounting base as a template. 2. Fix the camera mounting base to the ceiling with four screws (not provided, M4). Note:Remove sharp edges to protect the cables.3. Assemble the Camera Reverse the disassembly procedure. Take care not to cut any cables. OFFTermination ON...
Page 45
47 5. Tighten the fixing screw M3 (provided). Notes: (1) Tighten the camera fixing screw with a screwdriver. (2) Follow the instructions given here to ensure that the camera and camera mounting base are installed safely. (3) When removing the camera from the camera mounting base, loosen and press up the camera fixing screw (M3) by using a screwdriver. 6. Fix the decoration cover to the camera mounting base. a. Sideway Cable Exit Pass the cables through the cutout made in the diecast case and decoration...
Page 46
48 How to Assemble the Cable with the Accessory Connector Strip back the cable jacket approx. 3 mm (0.1 inch) and separate the individual conductors. Recommended wire gauge sizes for 24 V AC line #24 (0.22mm2) Copper wire size (AWG) Length of cable (approx.)(m) (ft)#22 (0.33mm2)#20 (0.52mm2)#18 (0.83mm2) 20 30 45 75 65 100 160 260 Accessory Connector Information Pin no. Power source 1 2 3 424 V AC LIVE 24 V AC NEUTRAL Ground Not use ContactUp Wire Prepare the individual conductors for clamping. Use MOLEX...
Page 47
49 • RS485 Connection Note: Use the cable that is described below for RS485 site communication. •Shielded, twisted pair cable •Low impedance •Wire gauge size is thicker than AWG #22 (0.33 mm 2). GND Brown Red Data transmission Data receptionOrange Yellow Green T (B) T (A) R (B) R (A)
Page 48
50 Note:When any peripheral is turned off and turned on again, the camera is also turned off and turned back on. SYSTEM CONNECTIONS 123456789MON CAM ESC SET0ACK RESETBACK SEQFORWARD SEQ ALTDEC –1CAMINC +1CAM STOP12AUXCLOSE OPENIRISPRESETFOCUS NEAR ZOOM TELE FAR WIDESystem Controller WV-CU550550BLEFT RIGHTUP DOWN ALARMBUSYF3F4F2F1AF123456789MON CAM ESC SET0ACK RESETBACK SEQFORWARD SEQ ALTDEC –1CAMINC +1CAM STOP12AUXCLOSE OPENIRISPRESETFOCUS NEAR ZOOM TELE FAR WIDESystem Controller WV-CU550550BLEFT...
Page 49
51 Zoom ratio Bright object SmearWhen the camera is aimed at a bright light, such as a spotlight, or a surface that reflects bright light, smear or blooming may appear. Therefore, the camera should be operated carefully in the vicinity of extremely bright objects to avoid smear or blooming. SPECIFICATIONS PREVENTION OF BLOOMING AND SMEAR Power source3.65 mm (H) x 2.71 mm (V), 1/4” 768 (H) x 494 (V) Dimensions Focus speed Effective pixels 15.724 kHz F1.6 - 22, CLOSE Focal length BLC 24 V AC, 60 Hz...
Page 50
52 Controls Auto focus Panning range Weights and dimensions indicated are approximate. Specifications are subject to change without notice.360°endless possible (in auto-pan mode) manual/sequential position/sort position/auto pan manual : approx. 0.1°/s - 120°/s 8-steps/64-steps sequence position : maximum approx. 300°/s 0°- 90° manual/sequential position/sort position manual : approx. 0.1°/s - 120°/s. 8-steps/64-steps sequential position : maximum approx. 300°/s pan/tilt, lens, 32 preset positions, home...