OKI C9600HDTN User Manual

C9600 User’s Guide> 31
the face-up paper stacker. This ensures that the paper path through 
the printer is almost straight.
The multi-purpose tray can feed paper widths as small as 76.2mm 
and lengths up to 1200mm. For banner printing, recommended 
sizes are A4 wide, 900mm and 1200mm long and weight 128g/m². 
Since paper of width less than 100mm does not autofeed, you have 
to press the ONLINE button to cause it to feed.
Use the multi purpose tray for printing on envelopes and 
transparencies. Up to 100...

C9600 User’s Guide> 32
TRAY AND STACKER EXAMPLES
LOADING TRAYS 1 TO 5
Tray 1 is used in the following example.
1.Pull out the tray.
2.Press the paper rear stopper tab (1) and adjust the tab to 
the required paper size.
3.Fan the paper to be loaded then tap the edges of the stack 
on a flat surface to make it flush.
1
Downloaded From ManualsPrinter.com Manuals 

C9600 User’s Guide> 33
4.Load the paper (face down and top edge towards the right 
for headed paper), press the tab (2) on the paper guide 
and adjust the guides (3) for a snug fit to the paper.
To avoid paper jams:
>Do not leave space between the paper and the guides 
and rear stopper.
>Do not overfill the paper tray. Capacity depends on the 
paper type.
>Do not load damaged paper.
>Do not load paper of different sizes or types at the 
same time.
23
Downloaded From ManualsPrinter.com Manuals 

C9600 User’s Guide> 34
5.Gently push the tray back into the printer.
USING THE MP TRAY
1.Squeeze the handle (1) and open the multi-purpose tray. 
1
Downloaded From ManualsPrinter.com Manuals 

C9600 User’s Guide> 35
2.Fold out the paper support section and swivel out the 
extension supports (2).
3.Adjust the paper guides (3) to the size of the paper being 
used.
4.Fan the paper to be loaded then tap the edges of the stack 
on a flat surface to make it flush.
2
3
Downloaded From ManualsPrinter.com Manuals 

C9600 User’s Guide> 36
5.Load the paper.
>For single-sided printing on headed paper, load the 
paper into the multi-purpose tray with pre-printed side 
up and top edge into the printer.
>For two-sided (duplex) printing on headed paper, load 
the paper with pre-printed side down and top edge 
away from the printer. (The duplex unit must be 
installed for this function.)
>Envelopes should be loaded face-up with long edge 
into the printer. Do not select duplex printing on 
envelopes.
>Do not leave space...

C9600 User’s Guide> 37
USING THE STACKERS
Face-down stacker
When the face-up stacker (1) on the left side of the printer is 
closed (its normal position), paper is ejected to the face-down 
stacker on the top of the printer.
Face-up stacker
The face-up exit path is used for heavy paper (cardstock etc.), 
envelopes, transparencies, and labels.
1.Open the stacker (1).
1
1
Downloaded From ManualsPrinter.com Manuals 

C9600 User’s Guide> 38
2.Flip out the paper support (2).
3.Swivel out the paper support extension (3).
2
3
Downloaded From ManualsPrinter.com Manuals 

C9600 User’s Guide> 39
CONTROL PANEL
The control panel can be swivelled to 90° (maximum) upwards 
from its base position (1) as required for ease of use.
CONTROLS AND INDICATORS
The parts of the control panel are identified and briefly explained 
below:
1. Shutdown/Restart button
Hold down for more than 2 seconds for a soft shutdown. 
You can then press this button again for a restart or use 
the Power switch to turn off the printer completely.
1
12
345
6 78
910
11
Downloaded From ManualsPrinter.com...

C9600 User’s Guide> 40
2. Ready indicator
On: indicates ready to print
Flashing: indicates processing print data
Off: indicates unable to receive data (offline)
3. Attention indicator
Off: indicates normal operation
Flashing: indicates error(s) present but printing can 
continue
On: indicates error(s) present and printing cannot continue
4. LCD panel
Displays status and setup information for the printer and 
user help information in your chosen language
5. Up-arrow button
Enters menu mode and enables...