NEC Neax 2400 Ipx Isdn Feature Programming Manual

NDA-24305 CHAPTER 3
Page 13
Revision 1.0
BASIC DATA ASSIGNMENT FOR ISDN
STEP 5: ACSC - Assign Dch and Bch location for CSCG.
- The values for CSCG is 130 through 255.
- Even number CSCGs are used for Dch location and odd number CSCGs are used for Bch
location. Although Bch location is the same as Dch location when PRT is used.
- CCH, which represents Dch and Bch location, is assigned as shown below.
- CCH must be assigned as the first group in the highway to which PRT is mounted.
- CCH=00000 is...

CHAPTER 3 NDA-24305
Pag e 1 4
Revision 1.0
BASIC DATA ASSIGNMENT FOR ISDN
(2) Condition: 24DTR is mounted in Slot 07 of PIM0 and 2DCH is mounted in Slot 05 of
PIM0, ACSC data is as follows.
Note 1:The location of DCH (Dch Handler) must be assigned in the “CCH” parameter of this command.
Note 2:Above is an example when #0 DCH of PA-2DCH circuit card is used.
STEP 6: ACIC1 - With respect to PC assigned in the ADPC command, assign CSCG of the Dch assigned in
the ACSC command.
STEP 7: ATRK - Assign the trunk...

NDA-24305 CHAPTER 3
Page 15
Revision 1.0
BASIC DATA ASSIGNMENT FOR ISDN
3. CALLING NUMBER PATTERN DATA (CNP) ASSIGNMENT
Calling party number can be transmitted included in the ISDN messages through ISDN network. This function
provides the PBX user with a variety of ISDN services. This section describes some conditions for programming
data related with this function when interworking with the Fusion link as shown Figure 3-3.
Figure 3-3   Calling Number When Interworking with FCCS Link
(1) This data should...

CHAPTER 3 NDA-24305
Pag e 1 6
Revision 1.0
BASIC DATA ASSIGNMENT FOR ISDN
STEP 2: ACNDN- Assign the number of digits to be added to or omitted from the calling party number  data
for each Calling Number Pattern programmed in ACNPN.
CNP=Calling Number Pattern assigned with ACNPN command.
SKIP=the number of digits to be skipped.
ADD=the number of digits to be added.
DC=the number to be skipped or added.
Note:Do not assign “0” at both “SKIP” and “ADD” parameter.
[Example Data] 
(2) Originating from the ISDN...

NDA-24305 CHAPTER 4
Page 17
Revision 1.0
CHAPTER 4 COMMANDS CONCERNING ISDN DATA ASSIGNMENT
1. GENERAL
This chapter explains commands concerning ISDN. Commands explained in Chapter 3, “Basic Data
Assignment for ISDN” are not included in this chapter.
 ASYD: Assignment of System Data       Note
 ASFC: Assignment of Service Feature Class Data       Note
 ARTD: Assignment of Route Class Data       Note
 ARTI: Assignment of Trunk Application Data
Note:This chapter covers only Index (data) related to ISDN. 

CHAPTER 4 NDA-24305
Pag e 1 8
Revision 1.0
COMMANDS CONCERNING ISDN DATA ASSIGNMENT
2. COMMANDS
2.1 ASYD: ASSIGNMENT OF SYSTEM DATA
SYSTEM
DATA
TYPE 
(SYS)SYSTEM
DATA 
INDEX 
(INDEX) 
0-511DATA 
(DATA) 
00-FF 
(Hex)BIT CORRE-
SPONDING 
DATA
SYSTEM DATA CONTENTS
DATA 
0/1BIT
1760b
0Not used Table Development:
Common or Separate 
Day/Night Data Tables.
Note:When data 
tables are 
designated as 
“Common”, 
the Day mode 
designation 
must be used 
in the 
respective 
commands. b
1Same Number Special Access...

NDA-24305 CHAPTER 4
Page 19
Revision 1.0
COMMANDS CONCERNING ISDN DATA ASSIGNMENT
Note 1:
Normally assign “0”. (Only specific service needs data “1” in this bit.)
Related Layer3 Timer: T303, T310, T313.
SYSTEM
DATA
TYPE 
(SYS)SYSTEM
DATA 
INDEX 
(INDEX) 
0-511DATA 
(DATA) 
00-FF 
(Hex)BIT CORRE-
SPONDING 
DATA
SYSTEM DATA CONTENTS
DATA 
0/1BIT
1220b
0Protocol of ISDN Terminal (BRI station)
0: Japan (INS64)
1: U.S.A. (5ESS)
2: Australia (TPH 1962)
3: Not used
4: Not used
5: N-ISDN1
6-15: Not used b
1
b2...

CHAPTER 4 NDA-24305
Pag e 2 0
Revision 1.0
COMMANDS CONCERNING ISDN DATA ASSIGNMENT
Note 1:
Available in Australia and U .A.E.
Note 2:For AT&T/Northern Telecom in U.S.A.
SYSTEM
DATA
TYPE 
(SYS)SYSTEM
DATA 
INDEX 
(INDEX) 
0-511DATA 
(DATA) 
00-FF 
(H ex)BIT CORRE-
SPONDING 
DATA
SYSTEM DATA CONTENTS
DATA  
0/1BIT
12300b
0-b6Not used
b
7Timing for receiving or sending ISDN/CCIS message. 
0/1 = 32 ms/128 ms
248b
0-b3
Maximum Digits for Call Forwarding External Restriction (for 
Australia only)
0: 12 digits...

NDA-24305 CHAPTER 4
Page 21
Revision 1.0
COMMANDS CONCERNING ISDN DATA ASSIGNMENT
2.2 ASFC: ASSIGNMENT OF SERVICE FEATURE CLASS DATA
SFI 31: For SID to Terminating User-DTE
0 = –
1 =  SID to Terminating User-DTE
SFI 48: For Bearer Service
0 = Speech
1  =  3.1 KHz Audio (Modem, G3 Fax)
SFI 94: For SID to Network - Privacy [CLIR]
0 = –
1  =  SID to Network - Privacy
SFI  175: For Advice of Charge (AOC) - Receipt and Display of AOC from a Foreign Q-SIG NETWORK
0 = Out of Service
1 = In Service
2.3 ARTD:...

CHAPTER 4 NDA-24305
Pag e 2 2
Revision 1.0
COMMANDS CONCERNING ISDN DATA ASSIGNMENT2.4 ARTI: ASSIGNMENT OF  TRUNK APPLICATION DATA
RST (CDN1) Assignment of Restart 0 = Restart Send per Individual Channel
1 = –
2 = –
3  = Restart not Send
HMT (CDN2)  When assigning this data, zero (0) should always be entered.
TRCRST (CDN3)  Call Restriction by Information transfer rate in B earer Capability Information Element
0 = No restriction
1 = Data call restriction (Unre stricted digital, Restricted digital and...