NEC Neax 2400 Imx Fusion Network System Manual

LIST OF FIGURES ND-70185 (E)
Pag e vi
Revision 3.0
LIST OF FIGURES  (CONTINUED)
Figure TitlePag e
Figure 5-2 Fusion-CCIS Network  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   60
Figure 5-3 How to Upgrade the Numbering Plan Data of an Existing CCIS Network . . . . . . . . . . . . . . . .   61
Figure 5-4 Assignment of Memory Block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   62
Figure...

ND-70185 (E) LIST OF FIGURES
Page vii
Revision 3.0
LIST OF FIGURES  (CONTINUED)
Figure TitlePag e
Figure 5-51 Sample Data Assignment (ACRD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   105
Figure 5-52 Sample Data Assignment (ACTK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   105
Figure 5-53 Assignment of FCHN (Example)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

LIST OF FIGURES ND-70185 (E)
Page viii
Revision 3.0
LIST OF FIGURES  (CONTINUED)
Figure TitlePag e
Figure 8-1 Network Connection Type  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   170
Figure 8-2 NEAX2000 IVS
2 to NEAX2400 IMX Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   171
Figure 8-3 NEAX2400 IMX to NEAX2400 IMX Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   172
Figure...

LIST OF TABLES
Table TitlePag e
ND-70185 (E) LIST OF TABLES
Page ix
Revision 3.0 Table 4-1 SENSE Switch Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  32
Table 4-2 MODE Switch Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  34
Table 4-3 DIP Switch (SW14) Setting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

LIST OF TABLES ND-70185 (E)
Pag e x
Revision 3.0
This page is for your notes. 

ND-70185 (E) CHAPTER 1
Page 1
Revision 3.0
CHAPTER 1 INTRODUCTION
1. General
This manual covers the installation of the Fusion system. 
2. How to Follow This Manual
This manual consists of the following chapters.
 CHAPTER 1 (INTRODUCTION)
Explains how to use this manual.
 CHAPTER 2 (GENERAL)
Outlines the Fusion system configuration and lists available service features.
 CHAPTER 3 (SYSTEM CONFIGURATION)
Explains the hardware configuration of the Fusion system.
 CHAPTER 4 (INSTALLATION)
Consists of the...

CHAPTER 1 ND-70185 (E)
Page 2
Revision 3.0
INTRODUCTION
Related Manuals
3. Related Manuals
To complete the installation of the Fusion system, the following manuals are required:
 NEAX2400 IMX Circuit Card Manual
 NEAX2400 IMX Installation Manual
 NEAX2400 IMX Office Data Specification
This manual assumes that the reader has sufficient knowledge of the installation of both the CCIS No. 7 and the
ACIS systems. For more information on these systems, refer to the related manuals. 

ND-70185 (E) CHAPTER 2
Page 3
Revision 3.0
CHAPTER 2 GENERAL
1. What is Fusion and its Advantages
The main advantages of the Fusion network are as follows:
1.1 Improved Inter-Office Service Features
The Fusion system can eliminate the constraints normally associated with network services that are offered
using Common Channel Inter-Office Signaling (CCIS).
1.2 Use of Telephone Numbers
A Fusion system allows you to use Telephone Numbers in addition to the existing station numbers. (In the
remainder of this...

CHAPTER 2 ND-70185 (E)
Page 4
Revision 3.0
GENERAL
Free Numbering
2. Free Numbering
A Telephone Number can be assigned to a desired station on the Fusion network using the simple command
operation shown below.
Figure 2-2   Free Location
2.1 Centralized Maintenance Administration Terminal (MAT)
A Fusion network has one Network Control Node (NCN) and Local Nodes (LNs). The NCN has the Cen-
tralized-MAT, which runs on Windows 95/NT. The MAT can collect fault information from all nodes on
the network. The...

ND-70185 (E) CHAPTER 2
Page 5
Revision 3.0
GENERAL
Fusion System Configuration
3. Fusion System Configuration
The Fusion system can be divided into the following two types. Figure 2-4 shows a Fusion system with Fusion
Call Control Handler (FCH) cards.
Figure 2-4   Fusion System Configuration (with FCH)
Figure 2-5 shows a Fusion system without Fusion Call Control Handler (FCH) cards.
Figure 2-5   Fusion System Configuration (without FCH)
FCH
CPU
LANI
HUB
FCH
CPU
LANI
HUB DTI
DTI DTI
FCH
HUB
DTIFusion...