NEC Neax 2000 Ivs2 Data Interface System Manual

CHAPTER 2 INSTALLATION
Installation Procedure for Data Interface
NEAX2000 IVS2 Data Interface System Manual    
ND-70924 (E), Issue 1.0   Page 43
DTI Cable Connection via CONN Card 
When you use an coaxial cable, connect the cable to a CSU via the CONN (PZ-M542/M557) card
as shown in Figure 2-22.
Figure 2-23 shows an example of the cable connection when the 30DTI card is mounted in the
AP05 slot of PIM0.
Figure 2-22  DTI Cable Connection via CONN Card
CSU
LT C 0 / LT C 1 / LT C 2 / LT C 3  COAXIAL CABLE...

 NEAX2000 IVS2 Data Interface System ManualPage 44  ND-70924 (E), Issue 1.0
CHAPTER 2 INSTALLATION
Installation Procedure for Data Interface
Figure 2-23  Example of Coaxial Cable Connection
2  COAXIAL CONNECTOR
1  LTC1 CONNECTOR
LTC1 (J) LTC1 (P)PIM0
JPCONN
30DTI
AP05
RA
RB
TA
TB17
42
18
4317
42
18
43TO CSU
LTC1
RECIEVE
RCV
TRANSMIT TRS
17 
18 
19 
20RA 
TA42 
43 
44 
45RB 
TB17 
18 
19 
20 RB 
TB 42 
43 
44 
45RA 
TA
2   1  

NEAX2000 IVS2 Data Interface System Manual    
ND-70924 (E), Issue 1.0   Page 45
CHAPTER 3
SYSTEM DATA
PROGRAMMING
This chapter explains the programming procedure to provide the Data
Interface to the PBX. 

 NEAX2000 IVS2 Data Interface System ManualPage 46  ND-70924 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
How to Read This Chapter
HOW TO READ THIS CHAPTER
In the programming procedure, the meaning of (1), (2) and markings are as follows.
(1) : 1st Data
(2) : 2nd Data
  :  Initial Data; With the system data clear command (CM00, CM01), the data with this
marking is automatically set for each command.
: A reset of the MP card is required after data setting.
Press SW1 switch on the MP card.
:A reset of...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Data Interface Assignment
NEAX2000 IVS2 Data Interface System Manual    
ND-70924 (E), Issue 1.0   Page 47
DATA INTERFACE ASSIGNMENT
DESCRIPTIONDATA
To assign data station number by CM1A, 
assign a station number (dummy number) 
to each port (LEN) on the DPC card.
NOTE 1:The station number must be
assigned to the first LEN (level
0) and the third LEN (level 2) of
each LT slot (The station
number must be also assigned
to the unused port on the DPC
card).
NOTE 2:The “*”...

 NEAX2000 IVS2 Data Interface System ManualPage 48  ND-70924 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Data Interface Assignment
DESCRIPTION DATA
Assign the attribute data for data station 
(assigned by CM1A) in accordance with 
the specification of the DTE connected.
(1)
(2)YY=04 Data speed
X-XXXXXXXX: Data Station No.
00-05 : 1200 bps
06 : 600 bps
07 : 1200 bps
08 : 2400 bps
09 : 4800 bps
10 : 9600 bps
11 : 19.2 kbps
12 : 48 kbps
13 : 56 kbps
14 : 64 kbps
15 : 7200 bps
16 : 14.4 kbps
17-31 :...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Data Interface Assignment
NEAX2000 IVS2 Data Interface System Manual    
ND-70924 (E), Issue 1.0   Page 49
DESCRIPTION DATA

(1)
(2)YY=08 Stop Bit
X-XXXXXXXX: Data Station No.
0 : 2-Stop Bit
1 : 1-Stop Bit
(1)
(2)YY=09 Type of Code
X-XXXXXXXX: Data Station No.
00 : ASCII (7-bit) + even parity
01 : ASCII (7-bit) + odd parity
02 : ASCII (7-bit) + parity (0)
03 : ASCII (7-bit) + parity (1)
04 : JIS (7-bit) + even parity
05 : JIS (7-bit) + odd parity
06 : JIS (8-bit)
07 :...

 NEAX2000 IVS2 Data Interface System ManualPage 50  ND-70924 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Digital Trunk Interface Assignment
DIGITAL TRUNK INTERFACE ASSIGNMENT
DESCRIPTION DATA
Assign an AP number to the DTI card. 
The AP number must match the SENSE 
switch setting on the DTI card.
(1)
(2)Y=0
04-15, 20-31: AP No.
09: DTI
Specify the AP highway channel for 
24DTI card.
(1)
(2)Y=1
04-15, 20-31: AP No.
0 : Expanded Highway channel
  (128 time slots)
1 : Basic Highway channel 
  (128...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Digital Trunk Interface Assignment
NEAX2000 IVS2 Data Interface System Manual    
ND-70924 (E), Issue 1.0   Page 51
DESCRIPTION DATA
Assign the necessary functions to the 
24DTI card.
After entering the data, set the MB switch 
on the DTI card to UP, and then to 
DOWN, for DTI initialization.
(1)
(2)
(1)
(2)
(1)
(2)
(1)
(2)YY=00 Data Mode
04-15, 20-31: AP No. assigned by
CM05 Y=0
0: Based on AT&T Spec.
YY=01 Frame Configuration
04-15, 20-31: AP No. assigned by 
CM05...

 NEAX2000 IVS2 Data Interface System ManualPage 52  ND-70924 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Digital Trunk Interface Assignment
DESCRIPTION DATA
CM35 Y=19 DTI PAD
[For Australia]
[For North America/Other Countries]
(1)
(2)YY=04 
Answer Signal from distant office
00-63: Trunk Route No.
2: Answer signal arrives

(1)
(2)YY=05 
Release Signal from distant office
00-63: Trunk Route No.
1 : Release signal arrives

(1)
(2)YY=09 Incoming Connection Signaling
00-63: Trunk Route No.
03: Wink...