Namco World Kicks Operators Manual

Page 41
Monitor Cabinet
Hex head screw
(M6x20)
with spring washerConnectors Hex head screw
(M6x20)
With spring washer
Kicker cabinet
5. Place the Kicker Cabinet close to the Monitor Cabinet and connect the
connectors.
6 . Push the Kicker Cabinet fully upto the Monitor Cabinet, taking care not to trap
any wires, and fit 4off hex head screws (M6x20), with spring washers. 

Page 42 5-3 Adjusting the Level Adjusters
1. When the game is in it’s final position ensure that all level adjusters are fully up.
2. Place an Adjustable Feet Strip Holder under the monitor cabinet rear level
adjusters, front level adjusters, and kicker cabinet rear level adjusters.
Place an Adjustable Feet Round Holder under each of the kicker cabinet front
level adjusters.
3. Lower all adjustable feet, ensuring that they fit the rebates of the holders, with a
spanner so that the cabinets are level and...

Page 43
6 ADJUSTMENTS
  
Adjustment or maintenance on this machine should be carried out by
qualified personnel only.
  
Einstellungen und Wartung des Gerätes dürfen nur von dafür
qualifiziertem Fachpersonal vorgenommen werden.
  
Justeringer eller vedligehold af denne maskine bør kun udføres af
kvalificeret personale.
  
Los ajustes y el mantenimiento de esta máquina deben ser realizados sólo
por personal cualificado.
  
L’installation, le service, le réglage, ou la maintenance...

Page 44
6-1 Adjustment Switches
The Adjustment switches are located inside the coin door. 
1. Service Switch. Press this switch to obtain game credits without incrementing the play meter.
2. Test Switch Slide the test switch ON to enter test mode. 
Test mode allows testing and the changing of game settings.  (Refer to section 6-2
 T est Mode  page 45)
3. Select Up/Down Switch This switch is used to select the test required when in the Test Mode.
4. Enter Switch This switch is used to enter a selected...

Page 45 6-2 Test Mode
1. Open the coin door and slide the test switch “ON”. The “Menu Screen” will be
displayed on the monitor.
2. Operating the Select Up / Down Switch will step through the tests. Select the test
required by pressing the Enter Switch.
3. Activate the test by pressing the Enter Switch. Select “EXIT” in each test to return
to the “Menu Screen”.
4. After testing is completed, slide the test switch to the “OFF” position to return to
normal game mode.
The Test Switch must always be in the...

Page 46 6-2-1 Coin Options
1. Select “COIN OPTIONS” on the menu screen to set the game cost and
related settings. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the
Enter button.
3. Use the Select Up/Down switch to change the setting.
4. Select “EXIT” and press the Enter button to return to the menu screen.
Note:- The price of play on this machine is set within the Cashflow Coin Mech. Ensure
that the Game Cost is set to 1 Coin 1 Credit.
COIN...

Page 47 GAME OPTIONS
[DEFAULT IN GREEN]
COMM BOARD NG ............................... (a)
COMMUNICATION OPTIONS ............................ (b)
(VS CPU MODE)
GAME TIME 90 (SEC) ............................ (c)
GOLDEN GOAL TIME 30 (SEC) ............................ (d)
GAME DIFFICULTY B (NORMAL) ............................ (e)
(VS PLAYER MODE)
GAME TIME 90 (SEC) ............................ (f)
GOLDEN GOAL TIME 30 (SEC) ............................ (g)
RETURN MATCH MODE OFF ...............................

Page 48 COMMUNICATIONS OPTIONS
[DEFAULT IN GREEN]
LINK : ON .......................................... (a)
LINK AS  : 1  (LEFT)
COMMUNICATION MODE ON .......................................... (b)
CPU ID 1 (LEFT) ................................. (c)
EXIT
SELECT SW :CHOOSE ENTER SW : ENTER
(b) Communications Options
This item is set when the communication cable is connected. (This is an optional
extra).
1. Select “COMMUNICATIONS OPTIONS” on the menu screen to set the
communication settings. The following...

Page 49 Settings for items (c) to (j)
m e t Ino i t p i r c s e Dte s y r o t c a F
e d o m U P C - e m i T e m a G ) c (0 0 3 , 0 4 2 , 0 8 1 , 0 5 1 , 0 2 1 , 0 9 , 0 6 , 0 3 . s d n o c e s n i e m i t e m a G
0 9
e d o m U P C - e m i T l a o G n e d l o G ) d (T I M I L O N , F F O , 0 9 , 0 6 , 0 3 , 5 1 e m i T l a o G n e d l o G d e d n e t x E
0 3
e d o m U P C - y t l u c i f f i D e m a G ) e () D R A H Y R E V D - Y S A E A ( D , C , B , A
L A M R O N ; B
e d o m r e y a l P - e m i T e m a...

Page 50I/O TEST
LINK : ON ....................................... (a) 
LINK AS : 1  (LEFT) ....................................... (b)
I/O PCB CHECK ....................................... (c)
HOW TO [I/F INITIALIZE] ....................................... (d)
SWITCH TEST ....................................... (e) 
EXIT
SELECT SW :CHOOSE ENTER SW : ENTER
I/O TEST
LINK ON 
LINK AS 1  (LEFT)
I/O PCB CHECK 
I/O PCB connect OK ............................ (
*
)
EXIT 
SELECT SW :CHOOSE ENTER SW : ENTER
6-2-3...