Mitsubishi Sd206u Projector User Manual
Here you can view all the pages of manual Mitsubishi Sd206u Projector User Manual. The Mitsubishi manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 21
EN-21 ENGLISH Password function This projector is equipped with the password function that is designed for prevention of wrong operation by children and restriction on operation by other than specified users. MENU ACCESS ............All the buttons except for the POWER button on the projector are disabled. (The buttons on the remote con- trol are enabled.) You can use this mode as a measure of pre- vention of wrong operation by children and restriction on operation by other than specified users....
Page 22
EN-22 Lamp replacement When the lamp no longer functions, replace it with a new one. Caution: Do not remove the lamp immediately after using the projector. You may get burned because the lamp very hot after use. Before replacing the lamp, press the POWER button to turn off the lamp and wait for two minutes for lamp to cool down. Unplug the power cord from wall outlet and wait one hour for the lamp to cool down completely. Do not remove the lamp except for replacement. Careless han- dling can cause...
Page 23
EN-23 ENGLISH Troubleshooting The following offers solutions to some of the common problems you may encounter. We suggest that you consult this chart before contacting your dealer. Images aren’t projected on the screen. ProblemCause and solution Power isn’t turned on. Check the states of the indicators. Images aren’t projected on the screen. Cancel the AV mute by pressing the MUTE button. Remove the lens cap. The lamp sometimes takes about one minute to light up. On rare occasion, the lamp...
Page 24
EN-24 Troubleshooting (continued) Images aren’t projected correctly. ProblemCause and solution Projected images are shaking. Projected images are displaced. Check that the cable connected to the external device isn’t intermittent. Connect the cable’s plug with the external device’s connector firmly. Press the AUTO POSITION button. Some computers output out-of-spec signals on rare occasion. Adjust the SIGNAL menu. (See page 19.) Projected images are distorted. Adjust the projector and the screen...
Page 25
EN-25 ENGLISH Others When the problems below occur after the lamp is replaced, check the following. Maintenance Warning:Do not use flammable solvents (benzene, thinner, etc.) and flammable aerosols when cleaning the projector body and lens. Flammable substances may ignite causing fire or breakdown while the lamp is illuminating. Caution: Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance on the projector. Cleaning of the projector and the...
Page 26
EN-26 Indicators This projector has two indicators, each of which shows the operation condition of the projector. The following offer solutions to possible problems. If these problem persist, turn the projector off and consult your dealer. Normal condition Abnormal condition POWERSTATUSCONDITIONNOTE Stand-by Power up process (About 4 seconds) The power is on. (Normal condition) Lamp cooling down. (About 90 seconds) Lamp lit up (About 60 seconds) STATUS indicatorPOWER indicator Steady redOff Blinking...
Page 27
EN-27 ENGLISH Specifications The specifications and outside appearance of the projector are subject to change without prior notice. Kensington Lock This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System. Refer to the information that came with the Kensington System for instructions on how to use it to secure the projector. Please contact Kensington Technology Group below. Kensington Technology Group 2855 Campus Drive San Mateo, CA 94403,...
Page 28
EN-28
Specifications (continued)
Connectors
Dimensional drawings (unit : mm)
What’s included in the box
Replacement part
15
11
610 15
pin No.Spec.
1VRED
2VGREEN
3VBLUE
4NC
5GND
6GND
7GND
8GND
9 VDC5V
10 GND
11 NC
12 VSDA
13 HSYNC
14 VSYNC
15 VSCLpin No.Spec.
1 DSUB_ROUT
2 DSUB_GOUT
3 DSUB_BOUT
4NC
5GND
6GND
7GND
8GND
9NC
10 GND
11 GND
12 NC
13 DSUB_HOUT
14 DSUB_VOUT
15 NC
MONITOR IN/OUT (Mini D-SUB 15-pin)
IN OUT
AC power cord
1 RGB cable for PC
1 VIDEO cableeither for US 02552-0063-01...
Page 29
EN-29 ENGLISH Specification of RGB signals in each computer mode of the projector Important: Some computers aren’t compatible with the projector. The projector’s maximum resolution is 800 x 600 pixels. It may not display images of higher resolutions than 800 x 600 correctly. Image with SYNC on G (Green) signal like 1080I may jitter. In this case, adjust FINE SYNC. in the signal menu. Images with SYNC on G (Green) signal may be tinged with green. If the resolution and frequency of your computer...
Page 30
MITSUBISHI Projector Contact Information Nor th America MESCA (Mitsubishi Electric Sales Canada Inc.) http://www.mitsubishielectric.ca Information Technologies Group, 4299 14th Avenue, Markham, Ontario L3R 0J2, Canada Sales & Technical Inquires Phone : +1-(800) 450-6487 Fax : +1-(905) 475-7958 E-mail : [email protected] Customer Care E-mail :[email protected] MDEA (Mitsubishi Digital Electronics America, Inc.) (Warranty Registration)...