Mitel Sx 200 Ml Pabx Lightware 16 Instructions Guide

Peripheral Equipment Troubleshooting Procedures 
EACH NO RELAY CONTACT 
MAY BE USED TO CONTROL 
‘A DEVICE, AS REQUIRED. 
1 RELAY MODULE 
Y 
LJ 
NOTE 1: ALL WIRING MUST BE DONE IN ACCORDANCE WITH THE NATIONAL NOTE 5: THE SUPERCONSOLE 7OOOAlTENDANT 
ELECTRICAL CODE (USA) OR CANADIAN ELECTRICAL CODE AND/OR CONSOLE MAY CONNECT TO ANY PORT ON A 
LOCAL ELECTRICAL INSPECTION AUTHORITIES. DIGITAL LINE CARD. 
THE DIGITAL LINE CARD MUST BE IN A HIGH 
NOTE 2: CROSS-CONNECT FIELD PIN NUMBERS FOR EACH MODULE DEPEND...

Troubleshooting 
Note: 1. Useful maintenance commands: SHOW STATUS, TEST, SHOW ALARMS, SHOW ERRORS 
CONSOLE - see the IX-232 Maintenance Terminal Practice. 
2. Loop resistance should not exceed 200 ohms. Voltage across Tip and Ring should be between 
40 and 48 volts dc. 
Table 3-13 SUPERCOIVSOLE 7000 Troubleshooting Procedures 
Step Possible Malfunction Source 
1. No connection between the SUPERCONSOLE 7000 attendant console and a Digital Line 
Card circuit. 
2. 
Faulty connections between the console...

Peripheral Equipment Troubleshooting Procedures 
HANDSET LIQUID 
CRYSTAL 
DlSPlAY 10 DISPLAY ASSOCIATIVE 
KEYS (SOFTKEYS) 
. ...” . . . ..-.. .“-- 
[Fl> [FZ> 
[FE+ [F7> 
[~6>= [F7>0 [F8> 0 [F9>0 
(FO’ 
Volye Vokme Co@ast Cy-@xt 
Ill, 
Telephone Number 
Func 
T!!! m-mm  nk 
P Cancel Release 
I , 
’ ’ “‘0~00000 
Page PBlock i%old 4+ rHoId 3 loHold 2 \‘Hold 1 ]%swer 
‘I/ I- 
7 LED 14 ATTENDANT CONSOLE 12 DIAL KEYS 
INDICATORS KEYS (FIXED KEYS) 2 VOLUME CONTROL KEYS 
2 CONTRAST CONTROL KEYS 
4 CURSOR CONTROL...

Troubleshooting 
Table 3-14 Attendant Console Error Indications 
indication 
HOLD 7 indicator flashing (after reset) 
HOLD 2 indicator flashing (after reset) 
HOLD 3 indicator flashing (after reset) 
All indicators on always (after reset) 
message: 
CONSOLE HARDWARE PROBLEM 123456789 
ERROR CODE 1 Meaning 
Console fault - replace console. 
y Console fault - replace console. 
Console fault - replace console. 
Console fault - replace console. 
Console fault - replace console. 
message: 
WAITING FOR...

Peripheral Equipment Troubleshooting Procedures 
SUPERSET 401+, and SUPERSET 410 Telephones 
The following table outlines, in descending order, the most likely items to cause 
malfunction. 
Table 3-l 5 SUPERSET 407+, and SUPERSET 410 Telephone Troubleshooting Procedures 
Item Possible Malfunction Source 
1. Faulty connections between the set and the cross-connect field. 
2. Faulty connections between the cross-connect field and the system. 
3. Faulty CDE programming; likely forms: 
l COS Define 
l...

Troubleshootingj 
Table 3-16 SUPERSET 420 
and SUPERSET 430 Telephone Troubleshooting 
Procedures (continued) 
Item Possible Malfunction Source 
3. Faulty CDE programming; likely forms: 
l COS Define 
l Stations 1 SUPERSETTelephones 
l Device Interconnection Table 
l System Configuration. 
4. Set requires reset - disconnect, reconnect line cord. 
5. Faulty SUPERSET telephone set or handset/cord assembly. 
6. Digital Line Card requires re-initialization (reseat card). 
7. Bay Control Card / Main Control...

Peripheral Equipment Troubleshooting Procedures 
Step 
4. 
5. 
6. 
7. 
l3. 
9. 
10. 
Il. 
12. 
13. Table 3-17 DATASET 1103 / DATASET 2103 - DTE Mode Troubleshooting 
Procedures (continued) 
Possible Malfunction Source 
Faulty CDE programming; likely forms: 
l COS Define 
l Stations / SWE%X~Telephones 
l Data Circuit Descriptor 
l Data Assignment 
l DTE Profile 
l Device Interconnection Table 
l System Configuration. 
Incorrect DATASET 2103 switch settings - see Table 3-l 8 through Table 3-23. 
Faulty far...

Troubleshooting 
Table 3-18 DATASET 2100 Switch Settings (Mode Selection) 
I I 
Switch No. Position Meaning 
1 Down Set - PBX operation 
tJP Hunt - Back to back mode 
2 
tJP Synchronous Operation 
Down Asynchronous Operation 
Note: The DATASET should be in the SET mode when connected to the system. 
Table 3-l 9 DATASET 2100 Switch Settings (Asynchronous Flow Control) 
Asynchronous Flow Switch No. 
Control Type 3 4 
Flow control disabled Down Down 
XON/XOFF flow control Down 
UP 
CTS flow control UP Down...

Peripheral Equipment Troubleshooting Procedures 
Table 3-21 DATASET 2100 Switch Settings 
I 
(Sync Operating Mode Selection) 
Meaning 
Transparent mode 
X.31 mode 
Table 3-22 DATASET 2100 Switch Settings 
(Synchronous Clock Source) 
Internal clock 
System clock 
TX external clock 
TX and Rx external clock Down 
Down 
“P 
“P Down 
“P 
Down 
“P 
Table 3-23 D3TASET 2100 Switch Settings (Sync Speed) 
Synchronous 
Speed Switch No. 
6 7 6 
1200 Down 
2400 
“P 
4800 
Down 
9600 
“P 
19200 X Down 
Down 
“P 
“P X...

Troubleshooting 
, 
RS-232 PHONE MODE LINE 
CONNECTOR JACK 
SWITCHES POWER JACK 
piiiiik#diq 
POWER 
LED ASYNC READY DEVICE AlTENTlON DISCONNECT 
LED LED LED KEY KEY 
BBO047 
Figure 3-8 DATASET 2103 Indicators and Connectors 
Table 3-24 DATASET 2103 LED indicators 
Indicator 
DEVICE 
Meaning 
ON - Indicates that the attached device is connected to the Dataset, 
and is supplying DSR or DTR on pin 21 of the RS-232 connector. 
FLASHING - Indicates that the Dataset is transmitting data 
OFF - Indicates that...