Home > Mitel > Communications System > Mitel SX-200 DIGITAL Pabx Engineering Information Manual

Mitel SX-200 DIGITAL Pabx Engineering Information Manual

Here you can view all the pages of manual Mitel SX-200 DIGITAL Pabx Engineering Information Manual. The Mitel manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 291

General Maintenance Information 
1. INTRODUCTION 
General 
1 .Ol This Section describes the maintenance philosophy, features, 
and facilities of the SX-ZOO@ DIGITAL Private Automatic Branch 
Exchange (PABX). Included are the use of diagnostic tests, maintenance 
aids, local and remote terminals, and other tools available to assist 
maintenance users in ensuring a continued high standard of efficiency 
and performance. Further details concerning SX-200@ DIGITAL PABX 
maintenance may be found in the...

Page 292

General Maintenance information 
2. SYSTEM OVERVIEW 
General- 
2.01 The SX-200@ DIGITAL PABX system is a fully electronic solid- 
state microprocessor-controlled switching system employing 
digital switching techniques and incorporating special peripheral de- 
vices and architecture to provide a modern integrated office commu- 
nications system. A block diagram of the system is shown in Figures 
2-l and 2-2. 
Maintenance 
2.02 The modular design and functional packaging of the system 
permits rapid...

Page 293

General Maintenance Information 
I ’ 
I 
I 
_; 
-- 
l =---I 
FLOPPY 
DISK 
DRIVE SUBSYSTEM 
512x512 CHANNELS) 
I 
I 
CONTROLLER 
TO/FROM 
PERIPHERAL 
DEVICES 
SAY 4 
KAOlSOR’ 
Figure 2-l System Block Diagram (336-Port Configuration) 
Page 2-2  

Page 294

General Maintenance Information 
tOL CARD 
1 I I I 1 I I 
LAY 1 AND BAY 2 
I’ I I I t II 6 DATA LINKS 
ADDRESS. DATA AND CONTROL BUS 
-1-i 1 RING LINK 
1 
PROCESSOR ----I 1 SPARE LINK 
I 
I 
DX ARRAV 
WlCJJYUC 
ClllrVCTFM I i I 116 x 16 LINKS) u PERIPHERAL L-!d 
1 DATA LINK 
1 i.ee1-1-1- _DK-I--_I.-.-J 1 
--- - -- - 
VOICE/DATA 
TO/FROM 
PERIPHERAL DEVICES 
3 DATA LINKS 
BAY 3 
I 
DIGITAL 
IN;EFW&E 
SUBSYSTEM 
C 
32 SPEECH N 
..: PATHS T 
R 
15 
VOICE 
CARDS 
I 
I 
I 
TO/FROM CONTROL 
PERIPHERAL DEVICES...

Page 295

General Maintenance Information 
PERIPHERAL SHELF 
r--I 
BAY 4 
BAV 3 
III 
I CONTROL SHELF MAINTENANCE PANEL 
FANS 
/ 
POWER 
DISTRIBUTION AC FILTER 
KAOP33RZE 
Figure 2-3 SX-200@ DIGITAL Equipment Cabinets (336~Port Configuration, Wnlwersa% 
SX-200@ DIGITAL Control Cabinet) 
Page Z-4  

Page 296

General Maintenance Information 
1 
CONTROL CABINET 
BAY 3- 
, 
, 
% 
- 
- 
I -BAY 5 
- BAY 4 
Figure 2-4 SX-200’ DIGITAL Equipment Cabinets (480-Port Configuration, Standard 
SX-200@ DIGITAL Control Cabinet) 
Page 2-5  

Page 297

General Maintenance Information 
Peripheral Equipment Cabinet (for 480-Port Configuration only) 
2.06 The door on the front of the SX-200@ DIGITAL peripheral equip- 
ment cabinet provides access to the peripheral maintenance 
panel, and two analog equipment bays. The rear doors provide access 
to the backplanes, equipment interface connectors and the SX-200@ 
DIGITAL power supply. Connection to the control equipment cabinet is 
made through the cable ducts located at the bottom of either of the 
cabinet...

Page 298

General Maintenance Information 
Figure 2-5 Attendant Console 
Page 
2-m  

Page 299

General Maintenance information 
3. MAINTENANCE AIDS 
The Maintenance Terminal 
3.01 The RS-232 ASCII Maintenance Terminal (see Figures 3-l and 
3-2) is the primary maintenance tool for the SX-200@ DIGITAL 
PABX. A wide range of commands are available at the maintenance 
terminal to help the user to locate and replace faulty equipment. For 
further information, refer to Section MITL9108-093-351-NA, RS-232 
Maintenance Terminal. 
3.02 The SX-200@ DIGiTAL Attendant Console (see Figure 2-5) may 
be used as...

Page 300

General Maintenance Information 
TERMINAL 
REMOTE - DEDICATED, PUBLIC NETWORK 
TERMINAL 
REMOTE - DIAL-UP 
x 
CROSS 
CONNECT 
i ASSIGNED 
TIP 81 RING PAIR 
FOR AUTO-ANSWER 
MODEM. TO DPAEX VIA 
CENTRAL OFFICE 
MODEM 
REMOTELV LOCATED 
TERMINAL 
NOTE: The Auto-Answer MODEM Is 
permanently connectad to one 
local statlon circuit (extenslont. 
XA0197ROEO 
Figure 3-l Maintenance Terminal Connection (Universal SX-SOB@ KJIGITAL Control Cabinet) 
Page 3-2  
Start reading Mitel SX-200 DIGITAL Pabx Engineering Information Manual

Related Manuals for Mitel SX-200 DIGITAL Pabx Engineering Information Manual

All Mitel manuals