Home > Mitel > Communications System > Mitel SX-200 DIGITAL Pabx Engineering Information Manual

Mitel SX-200 DIGITAL Pabx Engineering Information Manual

Here you can view all the pages of manual Mitel SX-200 DIGITAL Pabx Engineering Information Manual. The Mitel manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 281

RS-232 Maintenance Terminal 
APPENDIX B 
MAINTENANCE TERMllNAL ERROR MESSAGES 
81.01 The following Table lists all of the status and error messages 
which may appear at the maintenance terminal during a main- 
tenance session: 
TABLE 81-l 
MAINTENANCE TERMINAL ERROR MESSAGES 
SHOW STATUS command to check the status 
Use SHOW CONFIG command to check the 
The specified sub-circuit number is invalid for 
this particular device type. Use SHOW STATUS 
command to verify card type and number of 
Device could...

Page 282

RS-232 Maintenance Terminal 
TABLE al-1 (CONT’D) 
MAINTENANCE TERMINAL ERROR MESSAGES 
DATABASE sequence - try again when the 
system is less busy. May be problem with 
communication with diskette - check the 
connections to the disk drive. Verify that there 
is a diskette in the drive. Repeated failure 
indicates a problem - refer to Section 
MITL9108-093-350-NA, Troubleshooting. 
IC measurement 
is collecting data. 
Specifically, these are: 
from the console, the diskette is first updated. 
This...

Page 283

RS-232 Maintenance Terminal 
TABLE al-1 (CONT’D) 
MAINTENANCE TERMINAL ERROR MESSAGES 
- disk drive door is open 
- there is no diskette installed. 
TENANCE-PORT 
when ready an an error 
ears when changing the speed 
ort while on the 
Bay/Slot/Cct. of entering def 
and SUBCIRCUI 
“XX” in Bay/Slot/Cct. 
Circuit XX does not exist on this card. 
out of range ( 1 - 4 ). module number is out of range (i.e., not 
between 1 and 4). 
Universal Card. Sub-circuit X does does not 
exist on module YY. The user has...

Page 284

RS-232 Maintenance Terpinal 
TABLE B.l-1 (CONT’D) 
MAINTENANCE TERMINAL ERROR MESSAGES 
mmands both the bay a 
specified explicitly. 
to check range. 
TIMEOUT PERIOD EXPIRED. Press Return to 
login. 
Copy failed. Disk is write protected. a copy-protected 
rotect tab, or insert 
Page B-4/4  

Page 285

RS-232 Maintenance Terminal 
APPENDIX C 
lNSTALLAl-ION OF NEW SOFTWARE 
Cl.01 This Appendix outlines the procedures involved in the installa- 
tion of new or upgraded software. Additional information may 
be found in Section MITL9108-093-200-NA, Shipping, Receiving 
and 
Installation. The SX-200’ DIGITAL PABX software is stored on a single 
5 l/4 inch floppy diskette; the database is also stored here. When 
upgraded software is procurred, it is desirable to simply copy the 
customized database from the...

Page 286

RS-232 Maintenance Terminal 
TABLE Cl-l (CONT’D) 
NEW SOFTWARE INSTALLATION 
I I I 
Step Procedure 
9 
ress the CANCEL softkey, and 
software. 
Note: It will be possible to log into the maintenance terminal approximately 2 minutes 
after pressing the SYSTEM RESET pushbutton. 
Page C-2/2  

Page 287

MITEL STANDARD PRACTICE SECTION MITL9108-093-353-NA 
issue 2, September 1986 
SX-200” DIGITAL 
PRIVATE AUTOMATIC BRANCH EXCHANGE (PABX) 
GENERAL MAINTENANCE INFORMATION 
Copyright of MITEL Corporation 1986 
TM - Trademark of MITEL Corporation 
@Registered Trademark of MITEL Corporation  

Page 288

General Maintenance information 
CONTENTS 
PAGE 
1. INTRODUCTION ................................... l-l 
General ........... . ............................. l-l 
Reasonforlssue ................................. l-l 
The SUPERSET qTM Set ............................. l-l 
The SUPERSET 3TM Set ............................. l-l 
2. SYSTEM OVERVIEW ................................ 2-l 
General ......................................... 2-1 
Maintenance ..................................... 2-l 
Physical...

Page 289

General Maintenance information 
COiTENTS (CONT’D) PAGE 
Programming . . . . . . . . . . . . . . . . . . . . 0 . . . . a . . . . . n e . , . . 7-l 
Test Line Access 
. . . . . . . . . . . . . . . . . . . . . . . 0 . . . e . . . a m 7-1 
Test Line indicator LEDs . . . , . . . . . . . . . . . . . . . . . . . . . . . . 7-2 
Test LineTones . ..~.....~D.........~............. 7-2 
Command input . . . . . . . . . . . . . . . . ..-......-........ 7-2 
Commands Available D . . . . a . . . . . . . . . . . a n . 0...

Page 290

General Maintenance Information 
FIGURE TITLE PAGE 
2-5 Attendant Console . . . . . . . D . . . . . . . . . . . . . . . . . . . 2-7 
3-1 Maintenance Terminal Connection (Universal SX-200@ 
3-2 
3-3 
3-4 
3-5 
8-l 
8-2 
8-3 
8-4 ’ 
8-5 
8-6 
8-7 
8-8 
8-9 DIGITAL Control Cabinet) . . . . . . n . . . . . s m . . . . . . . 3-2 
Maintenance Terminal Connection (Standard SX-200@ 
DIGITAL Control Cabinet) n . . . . . . . . . . . . . . . . . . n . 3-3 
SX-200@ DIGITAL Control Cabinet Maintenance Panel...
Start reading Mitel SX-200 DIGITAL Pabx Engineering Information Manual

Related Manuals for Mitel SX-200 DIGITAL Pabx Engineering Information Manual

All Mitel manuals