Miele W 1714 User Manual

Front view
Inlet hose (tested to withstand
pressure of at least 7,000 kPa)
Electricity supply cable
-Flexible drain hose (with
detachable swivel elbow)
Detergent dispenser drawer	Control panel

Drum door
Access to drain filter, drain pump
and emergency release
Four height adjustable feet
Installation and connection
41 

Rear view
Protruding lid for holding when
moving the machine
Electricity supply cable
Inlet hose (tested to withstand
pressure of at least 7,000 kPa)
Drain hoseTransit bar covers
Restraining clip for inlet hose and
drain hose
Restraining clips for transit bars
when removed
Installation and connection
42 

Installation surface
A concrete floor is the most suitable
installation surface for a washing
machine, being far less prone to
vibration during the spin cycle than
wooden floorboards or a carpeted
surface.
Please note the following points:
The machine must be level and
securely positioned.
To avoid vibrations during spinning,
the machine should not be installed
on soft floor coverings.
If installing on a wooden joist floor:
We recommend a plywood base (at
least 59x52x3 cm). The base should
span...

Using the spanner supplied, turn the
left-hand transit bar 90°, then

withdraw the transit bar.Turn the right-hand transit bar 90°,
then

withdraw the transit bar.
Installation and connection
44 

To avoid the risk of injury the
holes for the transit bars must be
covered after the transit bars have
been removed.
Fit the covers onto the two holes.
Then plug the holes as shown with
the caps.Secure the transit bars to the back of
the washing machine. Make sure that
holesare fitted over retainers.
The machine must not be moved
without the transit bars in place.
Store them as shown or keep them
in a safe place for future use. They
must be re-fitted if the machine is to
be moved again (e.g. when...

Levelling the machine
The machine must stand perfectly level
on all four feet to ensure safe and
proper operation.
Incorrect installation may increase
electricity and water consumption and
may cause the machine to move about.
Screwing out and adjusting the feet
The four adjustable screw feet are used
to level the machine. All four feet are
screwed in when the machine is
delivered.

Using the spanner supplied turn
counternut2in a clockwise direction.
Then turn counternut2together with
foot1to...

Building under a worktop
The machine lid must not be
removed.
This washing machine can be pushed
under a worktop with its lid in place,
providing the worktop is high enough.Washer-dryer stack
A Miele tumble dryer can be stacked
with the washing machine. A WTV
stacking kit is necessary which can be
purchased from your Dealer, the Miele
Spare Parts Department or via the
internet on www.miele-shop.com.
Please note:
aSafety distance to wall:
at least 2 cm
bHeight:
Stacking kit with pull-out shelf:
approx....

The Miele water protection
system
The Miele water protection system
protects the washing machine from
water damage.
The system consists of three main
components:
1) the inlet hose
2) the electronic unit and the washing
machine housing
3) the drain hose
1) Inlet hose
The inlet hose can withstand
pressure of more than 7,000 kPa.
2) Electronic unit and washing
machine housing
– Sump
Any leaking water is collected in a
sump in the base of the machine. A
float switches off the safety valves,
preventing any...

Connection to the water
supply
The machine should be connected to a
mains water supply in accordance with
local and national safety regulations.
The German authorities do not require it
to have a non-return valve as the
washing machine has been designed
to comply with DIN regulations.
The machine is designed to operate
with a flow pressure of between
100 kPa and 1,000 kPa. If it is higher
than 1,000 kPa it is essential to fit a
pressure reducing valve.
Connection to the mains water supply
should...

Connection to the drainage
system
The machine drains via a drain pump
with a delivery head of 1 metre*. The
drain hose must not be kinked as this
restricts drainage. The swivel elbow at
the end of the hose can be turned in
either direction, or can be detached if
required, with a sharp twist and pull.
If required, the drain hose can be
extended to a length of 5 m. The
necessary parts can purchased from
the Miele Spare Parts Department or
your Miele dealer.
* For a delivery head of more than 1 m
(up to a...