Home > Miele > Dishwasher > Miele G 1272 Scvi Operating Instructions

Miele G 1272 Scvi Operating Instructions

    Download as PDF Print this page Share this page

    Have a look at the manual Miele G 1272 Scvi Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 171 Miele manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Buzzer
    An audible tone sounds at the end of
    the programme or if there is a fault.
    You will hear the buzzer at the end of a
    programme in bursts of five with a short
    pause in between. The buzzer will
    continue to sound for up to an hour if
    you do not switch the dishwasher off.
    In the event of a fault, the buzzer will
    sound continuously for up to two
    minutes if you do not switch the
    dishwasher off or correct the fault.
    The buzzer is activated as standard at
    the factory.
    You can deactivate the buzzer at the
    end of a programme if you wish. The
    buzzer will still sound if there is a fault,
    even if it has been deactivated.
    ^Open the door.
    ^Switch the dishwasher off with the Off
    button.
    ^Press the programme selector button
    in, andwhilst holding it inswitch
    the dishwasher on using the On
    button.
    Keep the programme selector button
    pressed in until the lower right hand
    programme indicator comes on.
    If this does not happen, start the
    procedure from the beginning again.^Press the Turbo/Combi tabs button
    four times.
    The Combi tabs indicator light will flash
    briefly four times at intervals.
    The message flashing in the Time left
    display shows whether the buzzer at
    the end of the programme is activated
    or deactivated.
    –p 1: the buzzer is activated
    –p0: the buzzer is deactivated
    ^To change the setting, press the
    programme selector button.
    The setting is now stored in memory.
    ^Switch the dishwasher off with the Off
    button.
    Additional functions
    41
     
    						
    							Factory default setting
    If you have altered any settings from
    the factory default, you can re-set them
    back to the factory default settings as
    follows:
    ^Open the door.
    ^Switch the dishwasher off with the Off
    button.
    ^Press the programme selector button
    in, andwhilst holding it inswitch
    the dishwasher on using the On
    button.
    Keep the programme selector button
    pressed in until the lower right hand
    programme indicator comes on.
    If this does not happen, start the
    procedure from the beginning again.
    ^Press the Turbo/Combi tabs button
    twelve times.
    The Combi tabs indicator light will give
    one long flash and two brief flashes at
    intervals.The flashing sequence in the Time
    display shows whether a setting other
    than the factory default setting has
    been set.
    –p1: All settings are set to factory
    default settings.
    –p0: At least one setting has been
    changed.
    ^To reset to the factory default
    settings, press the programme
    selector button.
    The setting is now stored in memory.
    ^Switch the dishwasher off with the Off
    button.
    Additional functions
    42
     
    						
    							Adjust Sensor wash
    You can adjust the Sensor wash
    programme so that it will remove
    stubborn soiling in a lightly soiled load.
    ^Open the door.
    ^Switch the dishwasher off with the Off
    button.
    ^Press the programme selector button
    in, andwhilst holding it inswitch
    the dishwasher on using the On
    button.
    Keep the programme selector button
    pressed in until the lower right hand
    programme indicator comes on.
    If this does not happen, start the
    procedure from the beginning again.
    ^Press the Turbo/Combi tabs button
    five times.
    The Combi tabs indicator light will flash
    briefly five times at intervals.The message flashing in the Time
    display shows whether the Adjust
    Sensor wash function is activated or
    deactivated.
    –p1: The Adjust Sensor wash
    function is activated.
    –p0: The Adjust Sensor wash
    function is deactivated.
    ^To change the setting, press the
    programme selector button.
    Switch the dishwasher off with the Off
    button.
    Additional functions
    43
     
    						
    							Check your dishwasher regularly
    (approx. every4-6months). This
    way faults and problems can be
    avoided.
    Miele branded cleaning and
    conditioning products are available
    from the Miele Spare Parts
    Department or via the internet at
    www.miele-shop.com.
    ,External surfaces of the
    dishwasher are susceptible to
    scratching.
    Contact with unsuitable cleaning
    agents can alter or discolour the
    outer surfaces.
    Cleaning the wash cabinet
    The wash cabinet is largely
    self-cleaning, provided that the correct
    amount of detergent is always used.
    If, however, there are limescale or
    grease deposits in the cabinet, these
    can be removed with a proprietary
    dishwasher cleaner or conditioner.
    Cleaning the door and the door
    seal
    ^Wipe the door seals regularly with a
    damp cloth to remove food deposits.
    ^When the dishwasher is being
    loaded, food and drink residues may
    drip onto the sides of the dishwasher
    door.
    These surfaces are outside the wash
    cabinet and are not accessed by
    water from the spray arms. Any
    soiling should be wiped off these
    surfaces before the door is closed.
    Cleaning the reflector panel
    The reflector panel for the In-operation
    indicator light is situated in the
    coverplate underneath the worktop.
    ^The reflector panel should only be
    wiped with a damp cloth or a suitable
    cleaning agent designed for use on
    plastic.
    Cleaning and care
    44
     
    						
    							Cleaning the control panel and
    door front
    ,Remove any soiling immediately.
    If not, it might become impossible to
    remove and could cause the outer
    surface to alter or discolour.
    ^The control panel shouldonlybe
    wiped with a damp cloth.
    ^Clean the front using a damp Miele
    microfibre E-cloth or with a sponge
    and a solution of hot water and
    washing-up liquid. Then dry with a
    soft cloth.To avoid damaging external
    surfaces, do not use:
    –cleaning agents containing soda,
    ammonia, acids or chlorides,
    –cleaning agents containing
    descaling agents,
    –abrasive cleaning agents, e.g.
    powder cleaners and cream
    cleaners.
    –solvent-based cleaning agents,
    –stainless steel cleaning agents,
    –dishwasher cleaner,
    – oven sprays,
    – glass cleaning agents,
    – hard, abrasive sponges and
    brushes, e.g. pot scourers,
    – sharp metal scrapers.
    Cleaning and care
    45
     
    						
    							Cleaning the filters in the wash
    cabinet
    The filter combination in the base of the
    wash cabinet retains coarse soil from
    the suds solution, preventing it
    accessing the circulation system and
    re-entering the cabinet through the
    spray arms.
    ,The dishwasher must not be
    used without all the filters in place.
    Collection of coarse soil may cause the
    filters to clog. The level of soiling and
    time it takes before the filters need
    cleaning will vary depending on use.
    Check the condition of the filters
    regularly and clean them if necessary.
    ^Switch the dishwasher off.^Turn the handle anti-clockwise to
    release the filter combinationa.
    ^Lift the filter combination out of the
    dishwasherb. Remove any coarse
    particles and rinse the filter well
    under running water. Use a nylon
    brush if necessary.
    Cleaning and care
    46
     
    						
    							To clean the inside of the filter, the flap
    must be opened:
    ^Press catchesatogether in the
    direction of the arrows as shown,
    and open the filterb.
    ^Rinse all the filters under running
    water.
    ^Then close the flap so that the catch
    engages.^Replace the filter combination so that
    it lies flat in the base of the wash
    cabinet.
    ^Then turn the handle clockwise, until
    the arrows line up, to lock the filter
    combination in place.
    ,Take care when you are fitting
    the filter combination that it is
    secured in position correctly.
    Otherwise coarse soil could get into
    the circulation system and cause a
    blockage.
    Cleaning and care
    47
     
    						
    							Cleaning the spray arms
    Particles of food can get stuck in the
    spray arm jets and bearings. The spray
    arms should therefore be inspected
    and cleaned regularly (approx. every
    4 - 6 months).
    ^Switch the dishwasher off.
    Remove the spray arms as follows:
    ^Take out the cutlery tray (if your
    dishwasher is fitted with one).
    ^Push thetopspray arm upwards to
    engage the inner ratchet. Then
    unscrew the spray arm.
    ^
    Push themiddlespray arms upwards
    ato engage the ratchet. Then
    unscrew the spray armb.^Remove the lower basket.
    ^Pull thelowerspray arm firmly
    upwards to remove it.
    ^
    Use a pointed object to push food
    particles into the spray arm jets.
    ^
    Rinse thoroughly under running
    water.
    ^
    Replace the spray arms and check
    that they rotate freely.
    Cleaning and care
    48
     
    						
    							With the aid of the following guide,faults in the performance of the appliance,
    some of which may result from incorrect operation, can be put right without
    contacting the Miele Service Department.
    ,Repairs should only be carried out by a suitably qualified and trained
    person in strict accordance with current local and national safety regulations.
    Unauthorised or incorrect repairs could cause personal injury or damage to the
    appliance.
    Technical problems
    Problem Possible cause Remedy
    The dishwasher does
    not start.The door is not properly
    closed.Push the door firmly shut.
    The appliance is not
    plugged in.Insert the plug and switch on
    at the socket.
    The fuse has tripped. Reset or replace the fuse.
    (Minimum fuse rating - see
    data plate).
    The appliance is not
    switched on.Press the On buttonand
    select a programme.
    The dishwasher
    stops during a
    programme.The fuse has tripped. Reset or replace the fuse.
    (Minimum fuse rating - see
    data plate).
    After the programme
    has started, the
    In-operation indicator
    light is not visible.The reflector panel was
    not correctly fitted.Re-fit the reflector panel
    correctly (see Installation
    diagram).
    Problem solving guide
    49
     
    						
    							Problem Possible cause Remedy
    The In-operation
    indicator is flashing
    quickly.
    The buzzer is sounding.
    All the programme
    indicators flash when
    the door is open.
    Fault code FXX shows
    in the display.There may be a
    technical fault.–Clean the water filter and
    clean the drain pump and
    non-return valve as
    described in
    Maintenance. If this does
    not resolve the problem:
    –switch the dishwasher off
    with the Off button.
    After a few seconds:
    –Switch the dishwasher
    back on.
    –Select the programme
    required with the
    programme selector
    button.
    – Close the door.
    If the indicator lights flash
    again, there is a technical
    fault.
    – Call the Service
    Department.
    The drain pump works
    even when the door is
    open.Fault F70:
    The Waterproof System
    has reacted.– Close the stopcock.
    –
    Call the Service
    Department.
    Problem solving guide
    50
     
    						
    All Miele manuals Comments (0)

    Related Manuals for Miele G 1272 Scvi Operating Instructions