Lucent Technologies PassageWay Service Provider For PARTNER Communications System Getting Started

							Installing and Configuring the PassageWay
Service Provider
2-18
   The PassageWay Configurator is launched, and it displays the
Find PassageWay Link dialog box.
Figure 2-4.  Find PassageWay Link Dialog Box
   The PassageWay Configurator is a software application that enables
you to set up the PassageWay Service Provider. Until you set up the
PassageWay Service Provider, you will be unable to use any TAPI
applications.
   Setting up the PassageWay Service Provider consists of specifying
the following information:
 ¾ the COM port to which the PassageWay adapter is connected
 ¾ the version and release of the PARTNER system your company has
(for example, PARTNER ACS R2.0)
 ¾ the type of telephone you have
 ¾ the extension number of your telephone 
						

							Installing and Configuring the PassageWay
Service Provider
2-19
 ¾ the location and telephone number of each outside line button on
your telephone
 ¾ the location of feature buttons on your telephone
  NOTE:
The PassageWay Configurator does not verify whether the
information you enter is correct. When you run a TAPI application
(for example, Microsoft Dialer), the PassageWay Service Provider
tries to use the information you entered via the PassageWay
Configurator. If the information you entered in the PassageWay
Configurator was correct, the TAPI application works properly. If
any of the information you entered is incorrect, the TAPI
application will not work. You must then run the PassageWay
Configurator and change the incorrect information.
   The Find PassageWay Link dialog box enables you to have the
PassageWay Configurator determine the COM port to which your
PassageWay adapter is connected.
  15.  Choose the Yes button.
   If the PassageWay Configurator found the COM port to which your
PassageWay adapter is connected, a message box appears, stating
that the PassageWay link was found and providing the number of the
COM port. Choose the OK button. The PassageWay Configurator -
COM Port dialog box appears, and the option button for the
corresponding COM port is selected.
   If the PassageWay Configurator did not find the COM port to which
your PassageWay adapter is connected, the PassageWay Link Not
Found message box appears. Choose the OK button. The
PassageWay Configurator - COM Port dialog box appears, and no
COM port option button is selected. 
						

							Installing and Configuring the PassageWay
Service Provider
2-20
Figure 2-5.  Sample PassageWay Configurator - COM Port Dialog Box 
						

							Installing and Configuring the PassageWay
Service Provider
2-21
  16.  Perform one of the following steps:
¾ If PassageWay “found” the COM port for you, choose the Continue
button.
¾ If PassageWay did not find the COM port for you, select the option
button of the COM port in your PC to which your PassageWay
adapter is connected, and then choose the Continue button.
   The PARTNER System Version dialog box appears.
Figure 2-6.  PARTNER System Version Dialog Box 
						

							Installing and Configuring the PassageWay
Service Provider
2-22
  17.  From the PARTNER System Version dialog box, select the PARTNER
system you are using, and then choose the Continue button.
   The Telephone Models dialog box appears.
Figure 2-7.  Telephone Models Dialog Box
  18.  Select the telephone you are using.
  19.  If a secondary device (such as answering machine or a fax machine)
is attached your PARTNER system phone, choose the 
Secondary
Device
 check box. 
						

							Installing and Configuring the PassageWay
Service Provider
2-23
  20.  Choose the Continue button.
   The Extension Number dialog box appears.   
Figure 2-8.  Extension Number Dialog Box
  21.  Enter your extension number, and then choose the Continue button.
   If you specified that you have a standard telephone, the Enter
Number dialog box appears. Enter the telephone number for the
outside line, and then choose the OK button. The PassageWay
Configurator - Complete message box appears. Proceed to Step 31.
   If you specified that you have a PARTNER system telephone, the
Phone Line Information dialog box appears for the telephone type you
specified. 
						

							Installing and Configuring the PassageWay
Service Provider
2-24
Figure 2-9.  Sample Phone Line Information Dialog Box
   This dialog box presents a representation of the buttons on your
telephone. Using this dialog box, you will specify the location for each
outside line on your telephone. 
						

							Installing and Configuring the PassageWay
Service Provider
2-25
  22.  Choose the location of an outside line on your telephone.
   A submenu appears, displaying the following options:
¾ Clear Button, which removes the programming (if any) and label (if
any) from the selected button.
¾ Outside Line, which enables you to specify the telephone number of
the outside line for the selected button.
¾ Cancel, which closes the submenu without changing the
programming for the selected button.
  
  NOTE:
   Make sure you specify the correct location of each outside line
on your telephone. If you incorrectly specify this information,
your system will not work as expected.
 23. Choose Outside Line.
   The Enter Number dialog box appears.
  24.  Enter the telephone number for the outside line, and then choose the
OK button.
   The button displays “LINE.”
  25.  Repeat Steps 22 through 24 for any other outside lines on your
telephone. 
						

							Installing and Configuring the PassageWay
Service Provider
2-26
  26.  When you are finished, choose the Continue button.
   The Feature Buttons dialog box appears.
Figure 2-10.  Sample Feature Buttons Dialog Box
   Using this dialog box, you specify the location of call handling
features assigned to buttons on your telephone by the PARTNER
System Manager. By specifying the locations of feature buttons,
telephony applications can use these call handling features to
enhance their operation. 
						

							Installing and Configuring the PassageWay
Service Provider
2-27
   The PassageWay Service Provider can recognize the following call
handling features programmed to your telephone:
 ¾ Auto Dial
 ¾ Call Forward
 ¾ Do Not Disturb
 ¾ Caller ID Inspect (Inspect)
  NOTE:
„Features that cannot be programmed to buttons on your
telephone are disabled (that is, you cannot program these
features).
„Make sure you specify the correct type and location of each
feature assigned to buttons on your telephone. If you incorrectly
specify any of this information, your system will not work as
expected.