LG Television Signature OLED W7 Manual

							55
Communication Parameters
•	Baud rate : 9600 bps (UART)
•	Data length : 8 bits
•	Parity : None
•	Stop bit : 1 bit
•	Communication code : ASCII code
•	Use a crossed (reverse) cable.
Command reference list
(Depending on model)
COMMAND1COMMAND2D ATA
(Hexadecimal)COMMAND1COMMAND2D ATA
(Hexadecimal)
01. Power*ka00 to 0115. Balancekt00 to 64
02. Aspect 
Ratiokc(p.7)
16. Color 
(Colour)
Temperature
xu00 to 64
03. Screen 
Mutekd(p.7)
17. ISM 
Method (Only 
Plasma TV)
jp(p.8)
04. Volume 
Muteke00 to 0118. Equalizerjv(p.8)
05. Volume 
Controlkf00 to 6419. Energy 
Savingjq00 to 05
06. Contrastkg00 to 6420. Tune 
Commandma(p.9)
07. 
Brightnesskh00 to 64
21. Channel
(Programme)
Add/Del(Skip)
mb00 to 01
08. Color/
Colourki00 to 6422. KeymcKey Codes
09. Tintkj00 to 64
23. Control 
Backlight, 
Control Panel 
Light
mg00 to 64
10. 
Sharpnesskk00 to 3224. Input 
select (Main)
xb(p.11)
11. OSD 
Selectkl00 to 0125. 3D (Only 
3D models)
xt(p.11 )
12. Remote 
Control Lock 
Mode
km00 to 01
26. Extended 
3D (Only 3D 
models)
xv(p.12)
13. Treblekr00 to 64
27. Auto 
Configure
ju(p.12)
14. Bassks00 to 64
* Note:   During playing or recording media, all commands except Power (ka) and \
Key (mc) are not 
executed and treated as NG. 
With RS232C cable, TV can communicate "ka command" in power-on or power-off status. but with 
USB-to-Serial converter cable, the command works only if TV is on.
ENG
ENGLISH 
EXTERNAL CONTROL DEVICE SETUP  
						

							66
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the TV. (j, k, m or x)
[Command 2]  : Second command to control the TV.
[Set ID]  :   You can adjust the [Set ID] to choose desired monitor ID number in option\
 menu.  
Adjustment range in TV is 1 to 99.  If [Set ID] value is selected to ‘0’, every connec\
ted set 
can be controlled.
     *  [Set ID] is indicated as decimal (1 to 99) on menu and as Hexadecimal (0x00 to 0x63) on 
transmission/receiving protocol.
[DATA]   : To transmit command data (hexadecimal).  Transmit ‘FF’ data to read status of command.
[Cr]   : Carriage Return - ASCII code ‘0x0D’
[   ]   : Space – ASCII code ‘0x20’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving normal data.\
 At this time, 
if the data is data read mode, it indicates present status data. If the \
data is data write mode, it returns the 
data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving abnormal dat\
a from  
non-viable functions or communication errors.
Data 00: Illegal Code
Real data mapping (Hexadecimal b Decimal)
* When you enter the [data] in hexadecimal, refer to following conversion \
table.
* Channel Tune (ma) Command uses two-byte hexadecimal value([data]) to select c\
hannel number.
00 : Step 032 : Step 50 (Set ID 50)   FE : Step 254
01 : Step 1 (Set ID 1)33 : Step 51 (Set ID 51)   FF : Step 255
.........
0A : Step 10 (Set ID 10)63 : Step 99 (Set ID 99)01 00 : Step 256
.........
0F : Step 15 (Set ID 15)C7 : Step 19927 0E : Step 9998
10 : Step 16 (Set ID 16)C8 : Step 20027 0F : Step 9999
.........
ENG
ENGLISH 
EXTERNAL CONTROL DEVICE SETUP  
						

							77
* Commands may work differently depending on model and signal.
01. Power (Command: k a)
 ►To control Power *On or Off of the set.
Transmission[k][a][  ][Set ID][  ][Data][Cr]
Data 00 : Power Off 01 : *Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
 ►To Show TV is Power On or *Off
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Ack [a][ ][Set ID][ ][OK][Data][x]
* Similarly, if other functions transmit ‘FF’ data 
based on this format, Acknowledgement feedback 
presents status about each function.
02. Aspect Ratio (Command: k c) 
(Main Picture Size)
 ►To adjust the screen format. (Main picture format) 
You can also adjust the screen format using the 
Aspect Ratio in the Q.MENU. or PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01 :  Normal screen 
(4:3)
 02 :  Wide screen 
(16:9)
  04 : Zoom
 05 : Zoom 2
   (Latin  America 
except Colombia 
Only)
 06 :  Set by Program/ 
Original
07 : 14:9
(Europe, Colombia, Mid-East, 
Asia except South Korea and 
Japan)
09 : * Just Scan
0B : Full Wide
(Europe, Colombia, Mid-
East, Asia except South 
Korea and Japan)
10 to 1F :   
Cinema Zoom 1 to 16
0c : 21:9 (Depending on model)
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3 
screen aspect ratio.
* In DTV/HDMI/Component mode (high-definition), 
Just Scan is available.
* Full wide mode may work differently based on 
model and is supported for DTV fully, and ATV, 
AV partially.
03. Screen Mute (Command: k d)
 ►To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00 :  Screen mute off (Picture on) 
Video mute off
  01 :  Screen mute on (Picture off)
  10 : Video mute on
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, TV will display On 
Screen Display(OSD). But, in case of Screen mute 
on, TV will not display OSD.
04. Volume Mute (Command: k e)
 ►To control volume mute on/off. 
You can also adjust mute using the MUTE button 
on remote control.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00 :   Volume mute on (Volume off)
 01 :  Volume mute off (Volume on)
Ack [e][ ][Set ID][ ][OK/NG][Data][x]
05. Volume Control (Command: k f)
 ►To adjust volume. 
You can also adjust volume with the volume 
buttons on remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
Data Min :   00 to Max : 64
Ack [f][ ][Set ID][ ][OK/NG][Data][x]
06. Contrast (Command: k g)
 ►To adjust screen contrast. 
You can also adjust contrast in the PICTURE 
menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min :  00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
07. Brightness (Command: k h)
 ►To adjust screen brightness. 
You can also adjust brightness in the PICTURE 
menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data Min :  00 to Max : 64
Ack [h][ ][Set ID][ ][OK/NG][Data][x]
ENG
ENGLISH 
EXTERNAL CONTROL DEVICE SETUP  
						

							88
08. Color/Colour (Command: k i)
 ►To adjust the screen Color(Colour). 
You can also adjust colour in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min :  00 to Max : 64
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
09. Tint (Command: k j)
 ►To adjust the screen tint. 
You can also adjust tint in the PICTURE menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red :   00 to Green : 64
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
10. Sharpness (Command: k k)
 ►To adjust the screen sharpness. 
You can also adjust sharpness in the PICTURE 
menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Data Min :  00 to Max : 32
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
11. OSD Select (Command: k l)
 ►To select OSD (On Screen Display) on/off when 
controlling remotely.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00 :  OSD off01 : OSD on
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
12. Remote control lock mode (Command: k m)
 ►To lock the front panel controls on the monitor and 
remote control.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00 : Lock off01 : Lock on
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
* If you are not using the remote control, use this 
mode. 
When main power is off & on (plug-off and plug-in, 
after 20 - 30 seconds), external control lock is 
released.
* In the standby mode (DC off by off timer or ‘ka’, 
‘mc’ command), and if key lock is on, TV will not 
turn on by power on key of IR & Local Key. 
13.  Treble (Command: k r)
 ►To adjust treble. 
You can also adjust in the AUDIO menu. 
Transmission [k][r][ ][Set ID][ ][Data][Cr]
Data Min :   00 to Max : 64
Ack [r][ ][Set ID][ ][OK/NG][Data][x]
* (Depending on model) 
14.  Bass (Command: k s)
 ►To adjust Bass. 
You can also adjust in the AUDIO menu. 
Transmission [k][s][ ][Set ID][ ][Data][Cr]
Data Min :  00 to Max : 64
Ack [s][ ][Set ID][ ][OK/NG][Data][x]
* (Depending on model) 
15. Balance (Command: k t)
 ►To adjust balance. 
You can also adjust balance in the AUDIO menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min :  00 to Max : 64
Ack [t][ ][Set ID][ ][OK/NG][Data][x]
16. Color(Colour) Temperature (Command: x u)
 ►To adjust colour temperature. You can also adjust 
Color(Colour) Temperature in the PICTURE menu.
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min :  00 to Max : 64
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
17. ISM Method (Command: j p) (Only Plasma TV)
 ►To control the ISM method. You can also adjust 
ISM Method in OPTION menu.
Transmission [j][p][ ][Set ID][ ][Data][Cr]
Data Min :  02: Orbiter 
08: Normal 
20: Color(Colour) Wash
Ack [p][ ][Set ID][ ][OK/NG][Data][x]
ENG
ENGLISH 
EXTERNAL CONTROL DEVICE SETUP  
						

							99
18. Equalizer (Command : j v)
 ►Adjust EQ of the set.
Transmission [j][v][ ][Set ID][ ][Data][Cr]
00000 00 0
MSB
Frequency DataLSB
765Frequency43210Step
0001st Band000000(decimal)
0012nd Band000011(decimal)
0103rd Band..................
0114th Band1001119(decimal)
1005th Band1010120(decimal)
Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]
* It depends on model, and can  adjust when sound 
mode is EQ adjustable value.
19. Energy Saving (Command: j q)
 ►To reduce the power consumption of the TV. You 
can also adjust Energy Saving in PICTURE menu.
Transmission [j][q][ ][Set ID][ ][Data][Cr]
Data 
 
00 : Off
 01 : Minimum
 02 : Medium
 03 : Maximum
 04 :   
Auto (For LCD TV / LED TV) /  
Intelligent sensor (For PDP TV)
 05 : Screen off
* (Depending on model)
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
20. Tune Command (Command: m a)
* This command may work differently depending on 
model and signal.
•	For Europe, Mid-East, Colombia, Asia except 
South Korea and Japan Model
 ►Select channel to following physical number.
Transmission [m][a][ ][Set ID][ ][Data 00][ ]
[Data 01][ ][Data 02][Cr]
* Analog Antenna/Cable
[Data 00][Data 01] Channel Data
Data  00 : High byte channel data
Data  01 : Low byte channel data
  - 00 00 ~ 00 C7 (Decimal : 0 ~ 199)
Data 02 : Input Source (Analog)
 - 00 : Antenna TV (ATV)
 - 80 : Cable TV (CATV)
* Digital Antenna/Cable/Satellite
[Data 00][Data 01]: Channel Data
Data  00 : High Channel data
Data 01 : Low Channel data
 - 00 00 ~ 27 0F (Decimal: 0 ~ 9999)
Data  02 : Input Source (Digital)
 - 10 : Antenna TV (DTV)
 - 20 : Antenna Radio (Radio)
 - 40 : Satellite TV (SDTV)
 - 50 : Satellite Radio (S-Radio)
 - 90 : Cable TV (CADTV)
 - a0 : Cable Radio (CA-Radio)
* Tune Command Examples:
1. Tune to the Analog antenna (PAL) Channel 10. 
Set ID = All = 00 
Data 00 & 01 = Channel Data is 10 = 00 0a 
Data 02 = Analog Antenna TV = 00 
Result = ma 00 00 0a 00
2. Tune to the digital antenna (DVB-T) Channel 01. 
Set ID = All = 00 
Data 00 & 01 = Channel Data is 1 = 00 01 
Data 02 = Digital Antenna TV = 10 
Result = ma 00 00 01 10
3. Tune to the satellite (DVB-S) Channel 1000. 
Set ID = All = 00 
Data 00 & 01 = Channel Data is 1000 = 03 E8 
Data 02 = Digital Satellite TV = 40 
Result = ma 00 03 E8 40
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][x][a][ ][Set ID][ ][NG][Data 00][x]
•	For South Korea, North/Latin America except 
Colombia Model
 ►To tune channel to following physical/major/minor 
number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
Digital channels have a Physical, Major, and Minor 
channel number. The Physical number is the actual 
digital channel number, the Major is the number that 
the channel should be mapped to, and the Minor is 
the sub-channel. Since the ATSC tuner automatically 
maps the channel from the Major / Minor number, 
the Physical number is not required when sending a 
command in Digital.
ENG
ENGLISH 
EXTERNAL CONTROL DEVICE SETUP  
						

							1010
* Analog Antenna/Cable
Data 00 : Physical Channel Number
 - Antenna (ATV) : 02~45 (Decimal: 2 ~ 69)
 -  Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125)
[Data 01 ~ 04]: Major/Minor Channel Number
Data  01 & 02: xx (Don't care)
Data 03 & 04: xx (Don't care)
Data 05: Input Source (Analog)
 - 00 : Antenna TV (ATV)
 - 01 : Cable TV (CATV)
* Digital Antenna/Cable
Data  00 : xx (Don't care)
[Data 01][Data 02]: Major Channel Number
Data 01 : High byte Channel Data
Data 02 : Low byte Channel Data
 - 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
[Data 03][Data 04]: Minor Channel Number
Data  03 : High byte Channel Data
Data 04 : Low byte Channel Data
Data 05 : Input Source (Digital)
 - 02 :   
Antenna TV (DTV) – Use Physical Channel 
Number
 - 06 :   Cable TV (CADTV) – Use Physical Channel 
Number
 - 22 :   
Antenna TV (DTV) – Don’t Use Physical 
Channel Number
 - 26 :   Cable TV (CADTV) - Don’t Use Physical 
Channel Number
 - 46 :   Cable TV (CADTV) – Use Physical/Major 
Channel Number Only (One Part Channel)
 - 66 :   Cable TV (CADTV) – Use Major Channel 
Number Only (One Part Channel)
 - 0b :   Cable DTV Plus – Use Physical Channel 
Number
 - 2b :   Cable DTV Plus – Don’t Use Physical 
Channel Number
 - 4b :   Cable DTV Plus – Use Physical/Major 
Channel Number Only (One Part Channel)
 - 6b :   Cable DTV Plus – Use Major Channel 
Number Only (One Part Channel)
Two bytes are available for each major and minor 
channel data, but usually the low byte is used alone 
(high byte is 0). 
* Tune Command Examples:
1.  Tune to the Analog cable (NTSC) channel 35. 
Set ID = All = 00 
Data 00 = Channel Data is 35 = 23 
Data 01 & 02 = No Major = 00 00 
Data 03 & 04 = No Minor = 00 00 
Data 05 = Analog Cable TV = 01 
Total = ma 00 23 00 00 00 00 01
2.  Tune to the digital antenna (ATSC) channel 30-3. 
Set ID = All = 00 
Data 00 = Don’t know Physical = 00 
Data 01 & 02 = Major is 30 = 00 1E 
Data 03 & 04 = Minor is 3 = 00 03 
Data 05 = Digital Antenna TV = 22 
Total = ma 00 00 00 1E 00 03 22
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][Data 03][Data 04][Data 05]
[x][a][ ][Set ID][ ][NG][Data 00][x]
•	For Japan Model
 ►To tune channel to following physical/major/minor 
number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
* Digital Antenna/Satellite
Data 00: xx (Don't care)
[Data 01][Data 02]: Major Channel Number
Data 01: High byte Channel Data
Data 02: Low byte Channel Data
  - 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
[Data 03][Data 04]:   Minor/Branch Channel Number 
(Don’t care in Satellite)
Data 03: High byte Channel Data
Data 04: Low byte Channel Data
Data 05 : Input Source (Digital/Satellite for Japan)
 - 02 : Antenna TV (DTV)
 - 42 :   
Antenna TV (DTV) – Use Physical/Major 
Channel Number Only (One Part Channel)
 - 62 :   
Antenna TV (DTV) – Use Major Channel 
Number Only (One Part Channel)
 - 07 : BS (Broadcasting Satellite)
 - 08 : CS1 (Communication Satellite 1)
 - 09 : CS2 (Communication Satellite 2)
* Tune Command Examples:
1 Tune to the digital antenna (ISDB-T) channel 17-1. 
Set ID = All = 00 
Data 00 = Don’t know Physical = 00 
Data 01 & 02 = Major is 17 = 00 11 
Data 03 & 04 = Minor/Branch is 1 = 00 01 
Data 05 = Digital Antenna TV = 02 
Total = ma 00 00 00 11 00 01 02
ENG
ENGLISH 
EXTERNAL CONTROL DEVICE SETUP  
						

							1111
2. Tune to the BS (ISDB-BS) channel 30. 
Set ID = All = 00 
Data 00 = Don’t know Physical = 00 
Data 01 & 02 = Major is 30 = 00 1E 
Data 03 & 04 = Don’t Care = 00 00 
Data 05 = Digital BS TV = 07 
Total = ma 00 00 00 1E 00 00 07
* This feature is varied based on the model.
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][Data 03][Data 04][Data 05]
[x][a][ ][Set ID][ ][NG][Data 00][x]
21. Channel(Programme) Add/Del(Skip) 
(Command: m b)
 ►To skip current channel(programme) for next time.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00 : Del(ATSC,ISDB)/Skip(DVB)01  : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* Set the saved channel status to del(ATSC, ISDB)/ 
skip(DVB) or add.
22. Key (Command: m c)
 ►To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Data  Key code - p.2.
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
23. Control Backlight (Command: m g)
•	For LCD TV / LED TV
 ►To control the backlight.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
    Control Panel Light (Command: m g)
•	For Plasma TV
 ►To control the panel light.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
24. Input select (Command: x b) 
(Main Picture Input)
 ►To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data 
 00 :   DTV
 02 :   Satellite DTV 
ISDB-BS (Japan)
 03 : ISDB-CS1 (Japan)
 04 : ISDB-CS2 (Japan)
 11 : CATV
01 : CADTV
10  : ATV
 20  : AV  or AV121  : AV2
 40 : Component1
     60 : RGB
41 : Component2
 90 : HDMI1
 92 : HDMI3
91 : HDMI2
93 : HDMI4
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* This function depends on model and signal.
25. 3D(Command: x t) (only 3D models)  
(Depending on model)
 ►To change 3D mode for TV.
Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01]
[ ][Data 02][ ][Data 03][Cr]
* (Depending on model)
Data  Structure
[Data 00]    00 : 3D On 
01 : 3D Off 
02 : 3D to 2D 
03 : 2D to 3D
[Data 01]   00 : Top and Bottom 
01 : Side by Side 
02 : Check Board 
03 : Frame Sequential 
04 : Column interleaving 
05 : Row interleaving
[Data 02]   00 : Right to Left 
01 : Left to Right
[Data 03]   3D Effect(3D Depth): Min : 00 - Max : 14 
(*transmit by Hexadecimal code)
ENG
ENGLISH 
EXTERNAL CONTROL DEVICE SETUP  
						

							1212
* [Data 02], [Data 03] functions depend on model 
and signal. 
* If [Data 00] is 00 (3D On), [Data 03] has no 
meaning.
* If [Data 00] is 01 (3D off) or 02 (3D to 2D), [Data 
01], [Data 02] and [Data 03] have no meaning.
* If [Data 00] is 03 (2D to 3D), [Data 01] and  
[Data 02] have no meaning.
* If [Data 00] is 00 (3D On) or 03 (2D to 3D), [Data 
03] works when 3D Mode (Genre) is manual only.
* All 3D pattern options ([Data 01]) may not be 
available according to broadcasting/video signal.
[Data 00][Data 01][Data 02][Data 03]
00OOO
01XXX
02XXX
03XOO
X : don’t care
Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02]
[Data03][x]
[t][ ][Set ID][ ][NG][Data00][x]
26. Extended 3D(Command: x v) (only 3D models) 
(Depending on model)
 ►To change 3D option for TV.
Transmission [x][v][ ][Set ID][ ][Data 00][ ]
[Data 01][Cr]
[Data 00]   3D option 
00 : 3D Picture Correction 
01 : 3D Depth (3D Mode is Manual Only) 
02 : 3D Viewpoint 
06 : 3D Color Correction 
07 : 3D Sound Zooming 
08 : Normal Image View 
09 : 3D Mode (Genre)
[Data 01]   It has own range for each 3D option 
determined by [Data 00].
1) When  [Data 00] is 00 
00 : Right to Left 
01 : Left to Right
2) When  [Data 00] is 01, 02
Data     Min: 0 - Max: 14 (*transmit by Hexadecimal 
code)
Data value range(0 - 20) converts Viewpoint range 
(-10  -  +10) automatically (Depending on model)
*  
This option works when 3D Mode (Genre) is manual 
only.
3) When   [Data 00] is 06, 07 
00 : Off 
01 : On
4) When  [Data 00] is 08 
00 :  Revert to 3D video from 3D-to-2D 
converted 2D video
    01 :  Change 3D video to 2D video, except 
2D-to-3D video
*  If conversion condition doesn’t meet, command is 
treated as NG.
5) When [Data 00] is 09
00 : Standard
02 : Cinema
04 : Manual
01 : Sport
03 : Extreme
05  : Auto
Ack [v][ ][Set ID][ ][OK][Data00][Data01][x]
[v][ ][Set ID][ ][NG][Data00][x]
27. Auto Configure (Command: j u) 
(Depending on model)
 ►To adjust picture position and minimize image  
shaking automatically. It works only in RGB (PC) 
mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr] 
Data 01 : To set Auto Configure
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
ENG
ENGLISH 
EXTERNAL CONTROL DEVICE SETUP