Kyocera KM 2035 User Manual

Copying Functions 
OPERATION GUIDE4-1
4 Copying Functions
This chapter explains the following topics.
• Making 2-Sided copies from various originals .............. 4-2
• Split Copy Modes ......................................................... 4-6
• Making a margin space on the copies .......................... 4-8
• Making copies with clean edges................................. 4-10
• Copying 2 or 4 originals onto a single page ............... 4-12
• Automatic Collating of copy...

Copying Functions 
4-2OPERATION GUIDE
Making 2-Sided copies from various originals
Copies of both sides can be made from open-faced originals as well as 
from 2-in-1 originals.
NOTE: The Duplex Unit (option) is necessary.
Making 2-Sided copies from a 2-Sided original
Front and Back side copies are 
made in the same way as duplex 
copies.
*1 2-Sided Copy reverse side 
rotation setting: OFF
*2 2-Sided Copy reverse side 
rotation setting: ON
NOTE: 
[Inch specifications]
The paper sizes that can be used are...

Copying Functions 
OPERATION GUIDE4-3
Making 2-Sided copies from an open-faced (book, etc.) original
The double-page original of 
books, magazines, etc. can be 
copied onto both sides of the 
paper by pressing [Start] one 
time.
NOTE: 
[Inch specifications]
The original sizes that can be used are Ledger and Letter. The paper 
sizes that can be used are Letter. A3, B4, A4R, B5R and A5R Original 
sizes can also be used when Custom Size is set.
The paper size can be changed and the magnification adjusted to...

Copying Functions 
4-4OPERATION GUIDE Original Left/Right Binding → 
Finished Top Binding: 
Setting the 2-Sided Copy 
reverse side setting to ON will 
result in the reverse side being 
copied after being rotated 180 
degrees. The finished copy is 
bound at the top, and each page 
spread copied in the same 
direction.
1Set the original.
NOTE: The underside Rotate Copy can also be set in the System Menu. 
(Refer to 2-Sided Copy Reverse Side Rotation Setting on page 4-5.)
The value set in the System Menu...

Copying Functions 
OPERATION GUIDE4-5 When the original has been set on the 
platen and the scanning of the original 
completed, Place next original. is 
displayed and the 2-Sided Copy display 
blinks. When this occurs, carry out the 
following procedure.
5Replace the original with the next one and press [Start].
The copier will scan the original.
6If there are no more originals to be scanned, press [2-sided] or [OK]. The 
copier will begin copying.
2-Sided Copy Reverse Side Rotation Setting
Follow the...

Copying Functions 
4-6OPERATION GUIDE
Split Copy Modes
Split copy from book originals
Copy books, magazines, etc. with 
two facing pages of an open-
faced original onto separate 
sheets of paper.
NOTE: 
[Inch specifications]
The original sizes that can be used are Ledger and Letter. The paper 
sizes that can be used are Letter. A3, B4, A4R, B5R and A5R Original 
sizes can also be used when Custom Size is set.
The paper size can be changed and the magnification adjusted to fit the 
size of the paper....

Copying Functions 
OPERATION GUIDE4-7
1Set the original.
2Press [Split], select the type of original, and select   or   to 
light up the corresponding display.
3Press [Start]. The copier will begin copying.
In the case where Collate Copies has been set, proceed to Step 4.
4Replace the original with the next one and press [Start]. The copier will 
scan the original.
5If there are no more originals to be scanned, press [OK]. The copier will 
begin copying.
Downloaded From ManualsPrinter.com Manuals 

Copying Functions 
4-8OPERATION GUIDE
Making a margin space on the copies
Standard Margin
[Inch specifications]
The position of the image of the 
original is shifted for copying and 
a 0.13/0.25/0.38/0.50/0.63/0.75 
()  (1/8-inch increments) width 
binding margin created.
[Metric specifications]
The position of the image of the 
original is shifted for copying and 
a 1 to 18 mm (1 mm increments) 
width binding margin created.
NOTE: If the left width of the Binding Margin is set when setting the 2-
Sided...

Copying Functions 
OPERATION GUIDE4-9 Setting the Margin
Use the procedure given below to change the Margin.
1Press [Margin] for 3 seconds. The System 
Menu for the Margin will be displayed.
2Press U or V and select the binding margin width. 
[Inch specifications]
0.13/0.25/0.38/0.50/0.63/0.75(): the range in which the margin can 
be set.
[Metric specifications]
A margin from 1 to 18(mm) can be set.
3Press [OK]. The display will blink and the copier will return to the state 
where copying can be...

Copying Functions 
4-10OPERATION GUIDE
Making copies with clean edges
Erasing blemishes from edges of copies (Sheet erase mode)
[Inch specifications]
Use this to remove the dark 
shading that appears around 
sheet originals during copying. 
Select the border width to be 
erased from among 0.13/0.25/
0.38/0.50/0.63/0.75 (). ((A) in the 
illustration is the Border Width.)
[Metric specifications]
Use this to remove the dark shading that appears around sheet originals 
during copying. Select the border width...