HP PhotoSmart Premium C309g User Manual

8.Press the ink cartridge back down into place.
The tab should make a snapping noise when the ink cartridge is correctly seated.
If the ink cartridge did not make a snapping noise, the tab might need to be
readjusted.
9.Remove the ink cartridge from the slot.
10.Gently bend the tab away from the ink cartridge.
CAUTION:Be careful not to bend the tab out more than about 1.27 cm
(0.5 inches).
11.Reinstall the ink cartridge.
It should now snap down into place.
Chapter 12
118 Solve a problem
Solve a problem
 

12.Close the ink cartridge access door, and check if the error message has gone
away.
13.If you still receive the error message, turn the product off, and then on again.
Cause:The ink cartridges were not installed properly.
If this did not solve the issue, try the next solution.
Solution 3: Contact HP support
Solution:Contact HP support for service.
Go to: www.hp.com/support.
If prompted, choose your country/region, and then click Contact HP for information
on calling for technical support.
Cause:There...

4.Lift the latch handle on the print carriage until it stops.
5.Remove the printhead by lifting it straight up.
6.Make sure the latch handle is raised, and then reinsert the printhead.
Chapter 12
120 Solve a problem
Solve a problem
 

7.Carefully lower the latch handle.
NOTE:Make sure you lower the latch handle before reinserting the ink
cartridges. Leaving the latch handle raised can result in incorrectly seated ink
cartridges and problems printing. The latch must remain down in order to
correctly install the ink cartridges.
8.Using the colored shaped icons for help, slide the ink cartridge into the empty slot
until it clicks into place and is seated firmly in the slot.
9.Close the ink cartridge door.
Cause:The printhead or ink...

If this did not solve the issue, try the next solution.
Solution 2: Contact HP support
Solution:Contact HP support for service.
Go to: www.hp.com/support.
If prompted, choose your country/region, and then click Contact HP for information
on calling for technical support.
Cause:There was a problem installing the printhead or ink cartridges.
Non-HP cartridge
Solution:Follow the prompts on the display to continue, or replace the indicated
ink cartridges.
CAUTION:HP recommends that you do not remove an ink...

NOTE:HP cannot guarantee the quality or reliability of non-HP supplies. Printer
service or repairs required as a result of using a non-HP supply will not be covered
under warranty.
If you believe you purchased genuine HP ink cartridges, go to:
www.hp.com/go/anticounterfeit
For more information, see:
“Replace the cartridges” on page 72
Cause:The original HP ink in the indicated ink cartridges was depleted.
Previously used genuine HP cartridge
Solution:Check the print quality of the current print job. If...

Printhead appears to be missing or damaged
Try the following solutions to resolve the issue. Solutions are listed in order, with the most
likely solution first. If the first solution does not solve the problem, continue trying the
remaining solutions until the issue is resolved.
•Solution 1: Reinstall the printhead and cartridges
•Solution 2: Contact HP support
Solution 1: Reinstall the printhead and cartridges
Solution:Check to make sure the printhead and the cartridges are installed.
To reinstall the...

5.Remove the printhead by lifting it straight up.
6.Clean the printhead.
There are three areas of the printhead that need to be cleaned: the plastic ramps
on both sides of the ink nozzles, the edge between the nozzles and the electrical
contacts, and the electrical contacts.
1Plastic ramps on the sides of the nozzles
2Edge between nozzles and contacts
3Electrical contacts
Errors 125
Solve a problem
 

CAUTION:Touch the nozzle and the electrical contact areas only with
cleaning materials and not with your finger.
To clean the printhead
a. Lightly dampen a clean, lint-free cloth and wipe the electrical contact area
from the bottom to the top. Do not go past the edge between the nozzles and
the electrical contacts. Clean until no new ink shows on the cloth.
b. Use a fresh, lightly dampened, lint-free cloth to wipe any accumulated ink and
debris from the edge between the nozzles and the contacts.
c. Use a...

d. Wipe the previously cleaned areas dry with a dry lint-free cloth before
proceeding to the next step.
7.Clean the electrical contacts inside the product.
To clean the electrical contacts in the product
a. Lightly dampen a clean, lint-free cloth with bottled or distilled water.
b. Clean the electrical contacts in the product by wiping with the cloth from top
to bottom. Use as many fresh, clean cloths as necessary. Clean until no ink
shows on the cloth.
c. Wipe the area dry with a dry lint-free cloth...