HP LaserJet 3050z User Manual

							Adjusting the lighter/darker (contrast) setting
The lighter/darker setting affects the lightness or darkness (contrast) of the copy. Use the following
procedure to change the contrast for the current copy job only.
To adjust the lighter/darker setting for the current job
1.On the all-in-one control panel, press  Lighter/Darker to see the current contrast setting.
2. Use the  < or the  > button to adjust the setting. Move the slider to the left to make the copy
lighter than the original, or move the slider to the right to make the  copy darker than the original.
3. Press  Start Copy  to save the selection and immediately start the copy job, or press 
 to save
the selection without starting the job.
NOTE The change in the setting remains active for  about two minutes after the copy job
has been completed. During this time,  Settings=Custom appears on the all-in-one
control-panel display.
To adjust the default lighter/darker setting
NOTE The default lighter/darker setting affects all copy jobs.
1.On the all-in-one control panel, press  Menu.
2. Use the  < or the  > button to select  Copy setup, and then press 
.
3. Use the  < or the  > button to select  Def. Light/dark, and then press 
.
4. Use the  < or the  > button to adjust the setting. Move the slider to the left to make all of the
copies lighter than the original, or move the slider to the right to make all of the copies darker
than the original.
5. Press 
 to save the selection.
ENWW Adjusting the lighter/darker (contrast) setting 123
 
						

							Reducing or enlarging copies
The all-in-one can reduce copies to as little as 25% of the original size or enlarge copies to as much
as 400% of the original size.
Reduction/enlargement settings
●Original=100%
● Lgl > Ltr=78%
● Lgl > A4=83%
● A4 > Ltr=94%
● Ltr > A4=97%
● Full Page=91%
● Fit to page
 (HP LaserJet 3052/3055/3390/3392 all-in-one only)
● 2 pages/sheet
● 4 pages/sheet
● Custom: 25-400%
NOTE
When using the  Fit to page setting, copy from the flatbed scanner only.
When using the  2 pages/sheet or 4 pages/sheet  setting, copy from the automatic document
feeder only. Also, after selecting the  2 pages/sheet or 4 pages/sheet  option, you must select
the page orientation (portrait or landscape).
Adjusting the copy size
To reduce or enlarge copies for the current job
1. On the all-in-one control panel, press  Reduce/Enlarge.
2. Select the size to which you would like to  reduce or enlarge the copies in this job.
NOTEIf you select  Custom: 25-400% , type a percentage by using the alphanumeric
buttons.
If you select  2 pages/sheet  or 4 pages/sheet , select the orientation (portrait or
landscape).
3. Press  Start Copy  to save the selection and immediately start the copy job, or press  to save
the selection without starting the job.
NOTE The change in the setting remains active for about two minutes after the copy job has
been completed. During this time,  Settings=Custom appears on the all-in-one control-panel
display.
You must change the default media size in the media input tray to match the output size, or
part of your copy might be cut off.
124 Chapter 7   Copy ENWW
 
						

							To adjust the default copy size
NOTEThe default copy size is the size to  which copies are normally reduced or enlarged. If
you keep the factory default size setting of Original=100%, all copies will be the same size as
the original document.
1. Press  Menu.
2. Use the  < or the  > button to select  Copy setup, and then press 
.
3. Use the  < or the  > button to select  Def. Redu/Enlrg , and then press 
.
4. Use the  < or the  > button to select the option for how you normally want to reduce or enlarge
copies.
NOTE If you select  Custom: 25-400% , type in the percentage of the original size that
you normally want for copies.
If you select  2 pages/sheet  or 4 pages/sheet , select the orientation (portrait or
landscape).
5. Press  to save your selection.
ENWW Reducing or enlarging copies 125
 
						

							Changing the number of copies
You can choose to have the default number of copies be any number from 1 to 99.
To change the number of copies for the current job (HP LaserJet 3050 all-in-one)
1. On the all-in-one control panel, use the alphanumeric buttons to type the number of copies
(between 1 and 99) that you want to make for your current job.
2. Press  Start Copy  to begin copying your job.
NOTEThe change in the setting remains active for about two minutes after the copy job
has been completed. During this time,  Settings=Custom appears on the all-in-one
control-panel display.
To change the number of copies for the current job (HP  LaserJet 3052/3055/3390/3392 all-in-one)
1. On the all-in-one control panel, press  # of Copies.
2. Use the alphanumeric buttons to type the number of copies (between 1 and 99) that you want to
make for your current job.
3. Press  Start Copy  to begin copying your job.
NOTEThe change in the setting remains active for about two minutes after the copy job
has been completed. During this time,  Settings=Custom appears on the all-in-one
control-panel display.
To change the default number of copies
1. On the all-in-one control panel, press  Menu.
2. Use the  < or the  > button to select  Copy setup, and then press 
.
3. Use the  < or the  > button to select  Def. # of copies , and then press 
.
4. Use the alphanumeric buttons to type the number of copies (between 1 and 99) that you want
as the default.
5. Press 
 to save your selection.
NOTE The factory-set default for the number of copies is  1.
126 Chapter 7   Copy ENWW
 
						

							Changing the copy-collation setting
You can set the all-in-one to automatically collate multiple copies into sets. For example, if you are
making two copies of three pages and the automatic collation is on, the pages print in this order:
1,2,3,1,2,3. If automatic collation is off, the pages print in this order: 1,1,2,2,3,3.
To use the automatic collation, the original document size must  fit into the memory. If it does not, the
all-in-one makes only one copy and a message appears notifying you of the change. If that happens,
use one of the following methods to finish the job:
● Split the job into smaller jobs that contain fewer pages.
● Make only one copy of the document at a time.
● Turn off the automatic collation.
The collation setting you select is in effect for all copies until you change the setting.
To change the copy-collation setting for the current job (HP LaserJet 3052/3055/3390/3392 all-
in-one only)
NOTE For the HP LaserJet 3050 all-in-one, change the default copy-collation setti\
ng to use
copy collation.
1. On the all-in-one control panel, press  Collate.
2. Use the  < or the  > button to select  On or  Off
3. Press  Start Copy  to save the selection and immediately start the copy job, or press 
 to save
the selection without starting the job.
To change the default copy-collation setting
1. On the all-in-one control panel, press  Menu.
2. Use the  < or the  > button to select  Copy setup, and then press 
.
3. Press 
 to select  Def. Collation .
4. Use the  < or the  > button to select  On or  Off.
5. Press 
 to save your selection.
NOTE The factory-set default for automatic copy collation is  On.
The  Collate LED on the control panel is on when collation is on.
ENWW Changing the copy-collation setting 127
 
						

							Copying onto media of different types and sizes
The all-in-one is set to copy on either letter- or A4-size paper, depending on the country/region in
which it was purchased. You can change the size and type of media that you copy to for the current
copy job or for all copy jobs.
Media-size settings
● Letter
● Legal
● A4
Media-type settings
● Plain
● Preprinted
● Letterhead
● Transparency
● Prepunched
● Labels
● Bond
● Recycled
● Color
● Light
● Heavy
● Cardstock
● Envelope
● Vellum
● Rough Paper
To change the media size and type for the current job (HP LaserJet 3052/3055/3390/3392 all-in-
one)
NOTE For the HP LaserJet 3050 all-in-one, change  the default media size and type settings
to change the media size and type.
1. On the all-in-one control panel, press  Paper.
2. Use the  < or the  > button to select a media size, and then press 
.
3. Use the  < or the  > button to select a media type, and then press 
.
4. Press  Start Copy .
128 Chapter 7   Copy ENWW
 
						

							To change the default media-size setting
1.On the all-in-one control panel, press  Menu.
2. Use the  < or the  > button to select  System setup, and then press 
.
3. Use the  < or the  > button to select  Paper setup, and then press 
.
4. Use the  < or the  > button to select  Def. paper size, and then press 
.
5. Use the  < or the  > button to select a media size and then press 
.
6. Press 
 to save the selection.
To change the default media-type setting
1. On the all-in-one control panel, press  Menu.
2. Use the  < or the  > button to select  System setup, and then press 
.
3. Use the  < or the  > button to select  Paper setup, and then press 
.
4. Use the  < or the  > button to select  Def. paper type, and then press 
.
5. Use the  < or the  > button to select a media type and then press 
.
6. Press 
 to save the selection.
ENWW Copying onto media of different types and sizes 129
 
						

							Copying two-sided documents (HP LaserJet 3050 all-in-
one)
To copy a multiple-page stack of two-sided documents (HP LaserJet 3050 all-in-one)
Copies resulting from this procedure are printed on one side, and need to be hand-collated.
1.Load the documents to be copied into the  automatic document feeder (ADF) input tray with the
first page facing down, and with the top of the page leading into the ADF.
2. Press  Start Copy . The odd-numbered pages are copied and printed.
3. Remove the stack from the ADF output tray and  reload the stack with the last page facing down,
and with the top of  the page leading into the ADF.
4.Press  Start Copy . The even-numbered pages are copied and printed.
5. Collate the odd- and even-numbered printed copies.
130 Chapter 7   Copy ENWW
 
						

							Copying two-sided documents (HP LaserJet 3052/3055
all-in-one)
To copy a multiple-page stack of two-sided documents (3052/3055 all-in-one)
Copies resulting from this procedure are printed on one side, and need to be hand-collated.
1.Load the documents to be copied into the  automatic document feeder (ADF) input tray with the
first page facing up, and with the top of the page leading into the ADF.
2. Press  Start Copy. The odd-numbered pages are copied and printed.
3. Remove the stack from the ADF output tray and reload the stack with the last page facing up,
and with the top of the page leading into the ADF.
4.Press  Start Copy. The even-numbered pages are copied and printed.
5. Collate the odd- and even-numbered printed copies.
ENWW Copying two-sided documents (HP LaserJet 3052/3055 all-in-one) 131
 
						

							Using automatic two-sided printing (duplexing) to copy
documents (HP LaserJet 3390/3392 all-in-one)
Use the 2-Sided button on the control panel display to use duplexing to achieve various\
 results.
NOTE The default setting is  1–1. The  2-Sided  LED on the control panel turns on when
another setting is used.
Table 7-1   2-Sided  settings
Document type2-Sided  settingResulting copies2-Sided LED
One-sided1–1One-sidedOff
One-sided1–2Two-sidedOn
Two-sided 2–2 Two-sided On
To make two-sided copies from one-sided documents
1.Load the documents to be copied into the  automatic document feeder (ADF) input tray with the
first page facing up, and with the top of the page leading into the ADF.
2. On the all-in-one control panel, press  2-Sided.
3. Use the  < or the  > button to select  Copy to 1 to 2 sided , and then press 
.
4. Press  Start Copy .
To make two-sided copies from two-sided documents
1. Load the documents to be copied into the  automatic document feeder (ADF) input tray with the
first page facing up, and with the top of the page leading into the ADF.
NOTE Two-sided copying from the flatbed scanner glass is not supported.
HP LaserJet 3390/3392
2.On the all-in-one control panel, press  2-Sided.
3. Use the  < or the  > button to select  Copy to 2 to 2 sided , and then press 
.
4. Press  Start Copy .
132 Chapter 7   Copy ENWW