HP DesignJet 4000 User Manual

4.Slide drawer 1 out until it touches the foam packaging.
5.Place the stand upside down on top of the printer body. Make sure you position the stand pins
in the holes in the center of the printer body brackets. The anti-slip material should face to the
rear of the printer.
6.Fix the right side of the stand to the printer using one screw. Make sure that the screw is fully
tightened.
ENWWAttach the stand 57
How do I... (printer
assembly topics) [4500]
 

7.Slide drawer 1 forwards to gain better access for the front screw. Fix the left side of the stand to
the printer using two screws. Make sure that the screws are fully tightened.
Attach the roll module
Before unpacking the roll module, note that you should handle this piece of equipment using only the
points indicated by the green arrows.
1.Open the box containing the roll module, then remove the two foam supports.
2.Remove the roll module from the packaging box.
58 Chapter 3   How do I... (printer...

3.Remove the roll module from the plastic bag.
4.Remove the remaining two yellow plugs from the left and right legs. It is important to remember
the positions of these holes.
5.Turn the roll module over into an inverted position as shown. Then carry it over to the front of
the inverted printer.
6.Rest the roll module next to the first printer crossbar.
1. The rear of the printer.
ENWWAttach the roll module 59
How do I... (printer
assembly topics) [4500]
 

7.Before the roll module is moved into its final position, please note that it should sit on the pins
that were located on the stand legs earlier.
8.With two people lifting the roll module and a third at the rear of the printer, guide the roll module
onto the pins located earlier on the stand.
9.When viewed from the front, make sure that the roll module sits against the legs of the stand.
60 Chapter 3   How do I... (printer assembly topics) [4500] ENWW
How do I... (printer
assembly topics) [4500]
 

10.Fix the roll module to the right leg of the stand.
11.Fix the roll module to the left leg of the stand.
12.Fix the roll module to the right leg of the stand using two additional screws.
ENWWAttach the roll module 61
How do I... (printer
assembly topics) [4500]
 

13.Fix the roll module to the left leg of the stand using two collar-headed screws.
Set up the printer
1.Place the spare and consumables boxes against the rear of the printer box. The arrows on the
boxes must point towards the printer box. Check that the anti-slip material is still fixed to the two
rear wheels.
2.Using four people, rotate the printer onto the spare and consumables boxes.
62 Chapter 3   How do I... (printer assembly topics) [4500] ENWW
How do I... (printer
assembly topics) [4500]
 

3.Rotate the printer until its rear rests on the spare and consumables boxes and the wheels with
the anti-slip material touch the floor.
4.Remove the pallet before trying to lift the printer into an upright position.
5.Using four people and the handholds on the rear of the printer body, carefully lift the printer into
an upright position.
6.Rotate the printer into an upright position. The anti-slip material should stop the printer from
sliding forwards.
ENWWSet up the printer 63
How do I... (printer...

7.Remove the two foam end packs and the plastic covering the printer.
8.Position the left leg cover on the front of the left leg (1), then clip the rear edge (2) into place.
9.Position the right leg cover on the front of the right leg (1), then clip the rear edge (2) into place.
10.Remove the anti-slip material from the two rear wheels on the stand assembly.
64 Chapter 3   How do I... (printer assembly topics) [4500] ENWW
How do I... (printer
assembly topics) [4500]
 

11.Remove the packing tapes 1 to 12.
12.Open the printer window. Then remove the two window inserts and the ink tube packing material.
13.Remove the protective covering from the printer window and the front panel screen.
14.Open the printhead cleaner door and remove the carriage packing material. Then close the
cleaner door.
ENWWSet up the printer 65
How do I... (printer
assembly topics) [4500]
 

15.Install the Quick Reference Guide holder. Angle the holder at the top (1), then position the two
hooks and clip the lower part (2) to the rear of the printer.
16.Remove the two yellow plastic screws from the right and left side of the paper feed.
17.Remove the two yellow plastic screws from the left and right side of drawer 2.
66 Chapter 3   How do I... (printer assembly topics) [4500] ENWW
How do I... (printer
assembly topics) [4500]