HP CM8060 User Manual

Menu itemSub-menu itemSub-menu itemValues and Description
Reset Security  Specify whether the current security settings on the
print server will be saved or reset to factory defaults.
No*: The current security settings are maintained.
Yes : Security settings are reset to factory defaults.
DiagnosticsEmbedded Tests This menu provides tests to help diagnose network
hardware or TCP/IP network connection problems.
Embedded tests help to identify whether a network fault
is internal or external to the device....

Menu itemSub-menu itemSub-menu itemValues and Description
 Ping Test This test is used to check network communications.
This test sends link-level packets to a remote network
host, then waits for an appropriate response.
  Dest TypeSpecify whether the target device is an IPv4 or IPv6
node.
  Dest IPV4Type the IPv4 address.
  Dest IPV6Type the IPv6 address.
  Packet SizeSpecify the size of each packet, in bytes, to be sent to
the remote host. The minimum is 64 (default) and the
maximum is 2048....

Menu itemSub-menu itemSub-menu itemValues and Description
  RefreshWhen viewing the ping test results, this item updates
the ping test data with current results. Select Yes to
update the data, or No to maintain the existing data.
However, a refresh automatically occurs when the
menu times out or you manually return to the main
menu.
Link Speed  The link speed and communication mode of the print
server must match the network. The available settings
depend on the device and installed print server. Select...

Fax Setup menu
NOTE:Use the fax setup wizard to configure fax options  if the analog fax accessory is installed. If the
analog fax accessory is not installed, the device ca n send faxes by using a LAN fax service or Internet
fax service. Use the embedded Web serv er to configure those services. See 
Use the embedded Web
server on page 88.
Table 7-11   Fax Setup menu
Menu itemSub-menu itemSub-menu itemValuesDescription
Fax Setup Wizard   Use this wizard to set up
options for sending faxes
if the analog...

Menu itemSub-menu itemSub-menu itemValuesDescription
 Redial On Busy The range is between 0
and 9. The factory default
is 3 times.Type the number of times
the device should attempt
to redial if the line is busy.
 Redial On No Answer Never
Once*
TwiceUse this feature to specify
the number of times the
device should attempt to
dial if the recipient fax
number does not answer.
 Redial Interval The range is between 1
and 5 minutes. The
factory default is 5
minutes.Use this feature to specify
the number of...

Menu itemSub-menu itemSub-menu itemValuesDescription
 Blocked Fax NumbersAdd Blocked NumbersType the fax number to
add to the list of blocked
fax numbers, then touch
the right arrow (
 ) to add
it to the list.
Use this feature to add or
delete numbers from the
blocked fax list. The
blocked fax list can
contain up to 30 numbers.
When the device receives
a call from one of the
blocked fax numbers, it
deletes the incoming fax.
It also logs the blocked fax
in the activity log.
Delete Blocked NumbersSelect a...

E-mail Setup menu
Use this menu to enable the e-mail feature and to configure basic e-mail settings. You can also configure
these settings by using the embedded Web server.
NOTE: To configure advanced e-mail settings, use the embedded Web server. For more information,
see 
Use the embedded Web server on page 88 .
Table 7-12   E-mail Setup menu
Menu itemSub-menu itemValuesDescription
E-mail Setup Wizard     Use this wizard to set up basic
options for the E-mail feature.
For more information, see...

Device Behavior menu
NOTE:This menu is also available through the embedded Web server. In the embedded Web server,
select the  Settings tab, and then select  Configure Device from the menu on the left side of the screen.
See 
Use the embedded Web server on page 88 .
NOTE: Values that have an asterisk (*) are the factory-default values. Some menu items have no
default.
Table 7-13   Device Behavior menu
Menu itemSub-menu itemSub-menu itemValuesDescription
Language  Select the language from
the list.Use...

Menu itemSub-menu itemSub-menu itemValuesDescription
Calibration Time  Hour, minutes, am and pm
(if the default time is am/
pm format)The device will attempt to
calibrate daily at the
scheduled Calibration
Time. Choose a time
when the device will not
be in use for
approximately one hour in
case a thorough
calibration is necessary.
At times of heavy use, the
device may calibrate more
often to retain high
imaging and printing
quality. Printing is paused
while calibrating but
should resume as soon as
the...

Menu itemSub-menu itemSub-menu itemValuesDescription
 Grain Direction 11x17 and
A3 Long-grain Paper
Short-grain Paper
(Default setting might vary
by country/region)Use this option to specify
the grain direction of
11x17 and A3 size paper
to be used in the device,
for paper weights less
than 120 g/m² (32 lb).
Long-grain paper can be
processed faster for these
larger paper sizes.
However, specifying
Long-grain Paper while
using a short-grain paper
can result in paper jams
and reduced print quality.
(If...