Epson Projector PT EZ590 User Manual

Chapter 3 Basic Operations — Projecting
ENGLISH - 51
Projecting
Check the attachment of the projection lens (
x page 38), external device connection (
x page 40), power 
cord connection ( x page 45), and switch on the projector (
x page 46) to start projecting. Select the image 
for projection, and adjust appearance of the projected image.
Selecting the input signal
Remote control
Control panel
The input for projection can be switched. Method to switch the input is as follows.  
f Press the input...

Chapter 3 Basic Operations — Projecting
52 - ENGLISH
Switching the input by displaying the input guide
The input for projection can be selected by displaying the input guide w\
ith the control panel.
1) 
Press the  button on the control panel.
 
f The
 [DETAILED]  input guide or the  [SIMPLE] input guide is displayed. (
x page 81)  
2)  Press the  button again.
 
f The input will switch each time you press the  button.
 
f You can also select the input source by pressing 
asqw on the remote control or...

Chapter 3 Basic Operations — Projecting
ENGLISH - 53
 
f Only [FOCUS] is shown in yellow so that the displayed menu item can be recognized by color
, even when the projector is not focused and 
displayed characters are unreadable. (Factory default)
Moving the lens to the home position
To move the lens to the home position, perform the following procedure.
1)  While the [SHIFT] adjustment screen is displayed, press the  button on the remote 
control.
 
f The 
[HOME POSITION]  screen is displayed.
2) While...

Chapter 3 Basic Operations — Operating with the remote control
54 - ENGLISH
Operating with the remote control
For PT-EZ590, PT-EW650  
and PT-EX620 For PT-EW550  
and PT-EX520
Using the shutter/AV mute function
If the projector is not used for a certain period of time during the meeting intermission, for example, it is possible to 
turn off the image and the audio temporarily.
 
r Shutter function
(Only for PT -EZ590, PT-EW650 and PT -EX620)
 button
1) Press the  button.
 
f The image and the audio...

Chapter 3 Basic Operations — Operating with the remote control
ENGLISH - 55
Using the mute function
Audio can be temporarily turned off.
 button
1) 
Press the  button.
 
f The audio disappears.
2)  Press the  button again.
 
f The audio reappears.
Adjusting the volume
The volume of the built-in speaker or audio output can be adjusted.
 button
1) 
Press the  button/ button.
 Decreases the volume.
 Increases the volume.
Note
 
f This operation can be also performed by using the  button/ button on the...

Chapter 3 Basic Operations — Operating with the remote control
56 - ENGLISH
Note
 
f If you press the  button on the control panel for at least three seconds while the on-screen display is of
f (hidden), the [OSD] 
individual adjustment screen is displayed. Press  qw to select [ON], then the on-screen display is turned on.
Using the automatic setup function
The automatic setup function can be used to automatically adjust the resolution, clock phase, and image position 
when analog RGB signals consisting...

Chapter 3 Basic Operations — Operating with the remote control
ENGLISH - 57
Switching the aspect ratio of the image
You can switch aspect ratios according to the input signal.
 button
1) 
Press the  button.
 
f The setting will change each time you press the button.
Note
 
f Refer to the [POSITION] menu 
→ [ASPECT] (
x page 78) for details.
Using the digital zoom function
(Only for still image-based RGB signals/still image-based HDMI signals/still image-based DIGIT
AL LINK signals 
input)
You can enlarge...

Chapter 3 Basic Operations — Operating with the remote control
58 - ENGLISH
Note
 
f The magnification is not displayed in the moving screen.
 
f The digital zoom function is canceled if the input signal changes during\
 a digital zoom.
 
f During a digital zoom, the freeze function is disabled.
 
f The digital zoom function may not work properly for some still image-bas\
ed signals.
Using the presentation timer function
The presentation timer function can be operated.
Presentations, etc. can be...

Chapter 3 Basic Operations — Operating with the remote control
ENGLISH - 59
2) 
Press qw to select the test pattern.
Note
 
f Setting is also available from the [TEST PATTERN] (
x page 99) menu.
 
f Settings of position, size, and other factors will not be reflected in test patterns. Make sure to display the input signal before performing 
various adjustments.
Using the status function
You can display the status of the projector.
 button
1) 
Press the  button.
 
f The 
[STATUS]  screen is displayed....

Chapter 3 Basic Operations — Operating with the remote control
60 - ENGLISH
Attention
 
f Since the ID number of the remote control can be set without the projector
, do not press the  button on the remote control 
carelessly. If the  button is pressed and no number ( - ) buttons are pressed within five seconds, the ID number returns to 
its original value before the  button was pressed.
 
f The ID number set on the remote control will be stored unless it is set again. However
, it will be erased if the...