Epson Powerlite 745c Technical Specifications

Epson PowerLite 745c Projector
8/04 Epson PowerLite 745c Projector - 11 Depending on whether your projector is set up to 
connect in Ad Hoc mode or Access Point mode (also called 
infrastructure mode), you see this screen:
3. If you’ve already configured the projector for your wireless 
network, go to “Projecting Wirelessly” on page 15. 
Otherwise, continue with the next section.
Configuring the Connection
You must configure both the projector and your computer’s 
network settings to project wirelessly....

Epson PowerLite 745c Projector
12 - Epson PowerLite 745c Projector 8/04 6. Select the appropriate settings for your mode:
7. When done making settings, highlight the 
OK button at 
the top of the screen. Then press 
Enter. Highlight the OK 
button again and press 
Enter to return to the main EasyMP 
Network Screen.
Configuring the Network Settings for Windows
Before connecting to the projector wirelessly, make sure your 
computer is configured correctly. Also, make sure that the 
Internet Connection...

Epson PowerLite 745c Projector
8/04 Epson PowerLite 745c Projector - 13 3. Click the 
Configure button. Then click the Advanced tab 
on the screen that appears. You see a screen like this:
4.Ad Hoc mode: Highlight 
Network Type in the Property 
list and set the Value to 
802.11 Ad Hoc.
Access Point mode: Highlight 
Network Type and set the 
Value to 
Infrastructure.
5.Ad Hoc mode: Highlight 
SSID and set the Value to match 
the name you gave the projector’s ESSID (for example, 
CONF ROOM). 
Access Point...

Epson PowerLite 745c Projector
14 - Epson PowerLite 745c Projector 8/04 12. Verify that you’ve enabled your computer’s connection to 
the access point. It should be listed as shown above, with 
the small icon  next to it, indicating a connection.
If it’s not listed, click 
Configure and then type the name of 
your access point.
13. When done, click 
OK. Continue with “Projecting 
Wirelessly” on page 15.
Checking the Gateway (Access Point’s) IP Address
If you’re entering IP addresses manually in Access...

Epson PowerLite 745c Projector
8/04 Epson PowerLite 745c Projector - 15 Projecting Wirelessly
Once you’ve started EasyMP and set up your projector and 
computer in either Ad Hoc mode or Access Point mode, 
follow these steps to start NS Connection and project 
wirelessly.
Note: 
You must have installed EMP NS Connection from your projector 
CD-ROM. See the User’s Guide for installation instructions.
1. Make sure you’ve inserted the Epson 802.11G/B card in 
the projector’s card slot (see page 10)....

Epson PowerLite 745c Projector
16 - Epson PowerLite 745c Projector 8/04 4. Once the name of your projector appears, select it and click 
Connect. If more than one projector is listed, you can 
select up to four additional projectors and connect to them 
at the same time. If the selected projector is being used by 
another person, you can still connect to it; doing so 
automatically disconnects the other user.
5. If you are prompted for a keyword, enter the four-digit 
number displayed on the EasyMP...

Epson PowerLite 745c Projector
8/04 Epson PowerLite 745c Projector - 17 3. Click 
Use IP connect mode, then click OK. You see this 
screen:
4. Click 
IP connection. You see this screen:
5. Enter the projector’s IP address and click 
Search.
The IP address appears in the Projector list and a 
searching icon displays.
If the search fails to find a projector with the specified IP 
address, the searching icon turns into a question mark. 
If this happens, run EasyMP to check the projector’s IP 
address, then...

Epson PowerLite 745c Projector
18 - Epson PowerLite 745c Projector 8/04
Managing Projectors from a Remote 
Computer
The software included with your projector lets you monitor 
and control projector(s) from a remote computer. These 
features are intended for use by network administrators. 
❏Use EMP Monitor to see your projectors’ status, switch 
image sources, and control basic settings.
❏Use the mail notification function to receive e-mail alerts 
about possible problems.
❏Use a network management...

Epson PowerLite 745c Projector
8/04 Epson PowerLite 745c Projector - 19 You see this screen listing all registered projectors:
Note: To delete a projector from the list, highlight the 
projector name, and click 
Delete.
5. Click 
Close. You see the status of each of your registered 
projectors on the main EMP Monitor screen:
Monitoring Your Projectors
The EMP Monitor screen lets you monitor your projectors 
using the Status, Video Source, and Error icons shown below. 
These let you see which projectors...

E pson P owerLite 745c P rojector
20 - Epson PowerLite 745c Projector 8/04 Controlling Your Projectors
The control buttons in the upper-right of the EMP Monitor 
screen let you turn the projectors on and off and select video 
signals. (Hold the mouse pointer over a button to see a 
description of its meaning.) Select the projector you want to 
operate (with the mouse pointer) before clicking one of the 
buttons. 
If you need the most current status information about your 
projectors, click the 
Refresh...