Eizo Coloredge Cg241w Users Manual

3. Screen Adjustment and Settings
21

3-4. Power-save Setup
The  menu in the ScreenManager enables to set the power-save setup.
NOTE
• Do your part to conserve energy, turn off the monitor when you are finished using it. Disconnecting 
the monitor from the power supply is recommended to save energy completely .
• Even if the monitor is in a power saving mode, USB compliant devices function when they are 
connected to the monitor's USB (both the upstream and the downstream ports). Therefore, power...

22
3. Screen Adjustment and Settings

3-5. Off Timer
The off timer function causes the monitor to automatically enter a power off state after a predetermined 
amount of time has lapsed. This function was created to reduce Afterimage characteristics that are 
particular to LCD monitors when the monitor screen is left on for a long period without use.
[Procedure]
1. Select  in the ScreenManager  menu.
2. Select “Enable” and touch the Right and Left directing switches to adjust the operating time (1 to 23...

3. Screen Adjustment and Settings
23

3-7. Power Indicator Setting
Light off the power indicator. This function is available for the multiple panels settings.
[Procedure]
1. Select  in the ScreenManager  menu.
2. Select "Disable".
3-8. Automatic brightness adjustment
The sensor on the front side of the monitor detects the environmental brightness to adjust the screen 
brightness automatically and comfortably.
[Procedure]
1. Select  in the ScreenManager  menu.
2. Select "Enable".
NOTE
•...

24
3. Screen Adjustment and Settings

3-9. Displaying Lower Resolutions
The lower resolutions are enlarged to full screen automatically. Using the  function in the 
 menu enables to change the screen size.
1  Enlarge the screen size when displaying a low resolution.
  Select the . 
Select the  in the  menu and select the screen size by using  and .
ModeFunction
FullDisplays the picture on the screen in full, irrespective of the picture's resolution. 
Since the verticalresolution and the horizontal...

3. Screen Adjustment and Settings
25

3  Set the brightness of the black area surrounding the displayed image.
 Set the .
In the  mode or  mode, the outer area (border) is usually black. Select 
 in the  menu and adjust by using .
3-10. Setting the orientation of the Adjustment menu
The orientation of the Adjustment menu can be changed.
[Procedure]
1. Select  in the ScreenManager  menu.
2. Use 
 to select between "Portrait" and "Landscape".
3-11. EIZO Logo Appearing Function
When...

26
4. Troubleshooting

4.Troubleshooting
If a problem still remains after applying the suggested remedies, contact your local dealer.
• No-picture problems : See No.1 - No.2
• Imaging problems : See No.3 - No.14
• Other problems : See No.15 - No.18
• USB problems : See No.19 - No.20
ProblemsPossible cause and remedy
1. No picture
• Power indicator does not light.
• Check whether the power cord is connected correctly. If 
the problem persists, turn off the monitor, and then turn 
it on again a few...

4. Troubleshooting
27

ProblemsPossible cause and remedy
3. Display position is incorrect.• Adjust image position so that it is displayed properly 
within the display area using the  adjustment 
(page 16).
•  Adjust image position so that it is displayed properly 
within the display area using the "Hor.Position" and "Ver.
Position" adjustment 
(page 16).
•  If the problem persists, use the graphics board’s utility if 
available to change the display position.
4. Screen image displayed is...

28
4. Troubleshooting

ProblemsPossible cause and remedy
14.Noise appears on the screen.• When entering the signals of analog input, select 1 to 
4 in  from the  menu to change 
the mode.
•  When entering the signals of HDCP system, the normal 
images may not be displayed immediately.
15.The  icon on the Adjustment menu 
 cannot be selected.
•   is disabled when the screen is displayed in 
the following resolutions.
•1920 × 1200
• Select "Enlarged" during  in the 
resolution of 800 × 600
•Select...

5. Reference
29

5. Reference
5-1. Attaching an arm
The LCD monitor can be used with an arm by removing the tilt stand and attaching the arm stand to the 
LCD monitor.
NOTE
• If you will use the arm or stand of other manufacturers, confirm the followings to the manufacturers 
before selecting.
- Hole spacing on the arm mounting 
100 mm x 100 mm (VESA compliant) 
- Supportable Weight: Total weight of the monitor (without stand) and attaching equipment such 
as a cable
- TÜV/GS approved arm or stand
•...

30
5. Reference

5-2. Environmental Settings (Digital signals only)
Depending upon your operating environment, it may be necessary to set the frequency that corresponds 
to your graphics board. If you install it for the first time or change environment, set the monitor.
NOTE
• Refer to the manual of the graphics board.
• These environment described below can be set regardless of whether or not the computer is running.
How to set
1  Press  to turn off the unit.
2  Press  again while pressing .
3  Select...