Eiki Projector Lc Xb250w User Manual

11
Part Names and Functions
Note:
To ensure safe operation, please observe the following precautions:
– Do not bend, drop, or expose the remote control to moisture or heat.
– For  cleaning,  use  a  soft  dry  cloth.  Do  not  apply  benzene,  thinner, 
spray, or any chemical material.
Remote Control
② AUTO SET button     Execute the setting of Auto setup (includes Input search, Auto 
     PC adj. and Auto Keystone functions) in the setting menu.
     (pp.23, 47)
⑤ S-VIDEO button  Select the S-VIDEO...

12
Part Names and Functions
To ensure safe operation, please observe the following precautions :
  Use two (2) AAA or LR03 type alkaline batteries.
  Always replace batteries in sets.
  Do not use a new battery with a used battery.
  Avoid contact with water or liquid.
  Do not expose the remote control to moisture or heat.
  Do not drop the remote control.
  If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.
  Risk of an explosion if battery...

13
Adjustable Feet
Positioning the Projector
For  projector  positioning,  see  the  figures  below. The  projector  should  be  set  perpendicularly  to  the  plane  of  the 
screen.
Installation
 Note:
	 •	The	brightness	in	the	room	has	a	great	influence	on	picture	quality.	It	is	recommended	to	limit	ambient	
     lighting in order to obtain the best image.
	 •	All	measurements	are	approximate	and	may	vary	from	the	actual	sizes.
Projection angle can be adjusted up to 12.0 degrees with 
the adjustable...

14
Installation
Connecting to a Computer
Cables used for connection 
•	VGA	Cables	(Mini	D-sub	15	pin)	*
•	Audio	Cables
•	DVI	cable
•	VGA-DVI	cable
(*One cable is supplied; other cables are not supplied with the projector.)
 Note:
	 •	When	the	MIC	function	is	set	to	Off in the Sound menu, the MIC function is disabled. (p 24)
	 •	When	MIC is set to On in Sound Menu, COMPUTER AUDIO IN 1, COMPUTER AUDIO IN 2 / MIC IN and 
AUDIO IN(L/R) terminals can be connected at the same time. At this time, COMPUTER...

15
Installation
Connecting to Video Equipment
Cables used for connection  
•	Video	and	Audio	Cable	(RCA 	x	3)	
•	S-VIDEO	Cable	
•	Audio	Cable	
(Cables are not supplied with the projector. )
U n p l u g   t h e   p o w e r   c o r d s   o f 
both  the  projector  and  external 
equipment  from  the  AC  outlet 
before connecting cables.
 Note:
  When the AUDIO OUT is plugged-in, the projector's built-
in speaker is not available.
External Audio Equipment
Audio cable   (stereo)
VIDEOS-VIDEO
S-Video...

16
Installation
Connecting to Component Video Equipment
 Note:
	 •	When	the	AUDIO	 OUT	is	 plugged-in,	 the	projector's	
built-in speaker is not available.
	 •	See	page	74	for	ordering	optional	cables.
U n p l u g   t h e   p o w e r   c o r d s   o f 
both  the  projector  and  external 
equipment  from  the  AC  outlet 
before connecting cables.
External Audio Equipment
COMPUTERAUDIO IN 1 
Audio cable (stereo)
Audio cable (stereo)
Audio Input
Component Video Output(Y, Pb/Cb, Pr/Cr)RGB Scart 21-pin...

17
Installation
Connecting the AC Power Cord
This projector uses nominal input voltages of 100-240 V AC 
and  it  automatically  selects  the  correct  input  voltage.  It  is 
designed to work with single-phase power systems having a 
grounded  neutral  conductor.  To  reduce  the  risk  of  electrical 
shock, do not plug into any other type of power system.
If  you  are  not  sure  of  the  type  of  power  being  supplied, 
consult your authorized dealer or service center.
Connect  the  projector...

18
The preparation display will disappear 
after 30 seconds.
(See page 54 for Lamp control status.)
Turning On the Projector
Connect  the  projector ’s  AC  power  cord  into  an  AC 
outlet. The  POWER  indicator  lights  red. Open  the  lens 
cap (see pages 8, 62).
Press  the  ON/STAND-BY  button  on  the  top  control  or 
on  the  remote  control.  The  POWER  indicator  lights 
green  and  the  cooling  fans  start  to  operate.  The 
preparation  display  appears  on  the  screen  and  the...

19
what is PIN code?
PIN  (Personal  Identification  Number)  code  is  a  security 
code  that  allows  the  person  who  knows  it  to  operate  the 
projector.  Setting  a  PIN  code  prevents  unauthorized  use  of 
the projector.
A PIN code consists of a four-digit number. Refer to the PIN 
code  lock  function  in  the  Setting  Menu  on  pages  55-56  for 
locking operation of the projector with your PIN code.
Enter a PIN code
Use  the  Point ▲▼  buttons  to  enter  a  number.  Press  the 
Point ►...

20
TO MAINTAIN THE LIFE OF THE LAMP, ONCE 
YOU TURN THE PROJECTOR ON, WAIT AT 
LEAST FIVE MINUTES BEFORE TURNING IT 
OFF.
Power off? disappears after 4 seconds.
Turning Off the Projector
Press  the  ON/STAND-BY  button  on  the  top  control  or 
on the remote control, and Power off? appears on the 
screen.
Press  the  ON/STAND-BY  button  again  to  turn  off  the 
projector. The POWER indicator starts to blink red, and 
the cooling fans keep running. (You can select the level 
of  fans’  quietness  and...