Eiki Projector Lc Hdt700 User Manual

							ENGLISH
11
ENGLISH
Chapter 2 
 Setup Procedures2
Describes how to configure the network. 
						

							12
Chapter 2 Setup Procedures
Setting Procedure
Setting procedures and contents differ depending on the LAN installation location.  
When installing, consult your system administrator to set up the LAN appropriately.
Connect the LAN cable to the LAN connection terminal of the projector.
Network configuration
Set the Wired LAN network through the projector menu. Detailed network settings will be 
made  with  browser.  Refer  to  “3.  Basic  setting  and  operation”  (p.17-31).  First,  complete  the 
settings  described  in  this  chapter  before  performing  steps  in  “3.  Basic  setting  and  opera-
tion.”
1. Select “Network” in the Network menu, and press Point  8 or SELECT  button.
2.   Select  "On"  with  the  Point  ed buttons,  and  the  press  SELECT  button.  Then  the  Menu 
will disappear, the “Please wait...” message will appear, and switching operation will start. 
Switching  will  take  a  while  and  the  projector’s  LINK/ACT  Lamp  will  be  on  or  blink,  and 
after completing the operation, the “Please wait...” message will disappear.
Connecting to the LAN line
LAN Cable
LAN Connection Terminal
LINK Lamp (Green)
Light green when the 
projector is connected to 
the network correctly.
ACT Lamp (Orange)
Blink orange when the 
projector is sending or 
receiving the data.
* Please use a shielded LAN cable. 
						

							13
ENGLISH
 
*1 Set "On" only when the DHCP server is available on your network environment.
*2 Set [255.255.255.255] if the network does not provide the gateway (router).
*3 Set [255.255.255.255] if you do not use the function E-mail alert.
3.  Select  "Network  setting"  in  the  Network  menu  and  press SELECT  button,  and  then  the 
LAN setting screen will appear and selected LAN settings will be displayed. Adjust each 
item  to  the  setting  environment.  Consult  your  system  administrator  about  the  detailed 
settings.
  Press  SELECT button in a row where you want to adjust, and adjust the figures with the 
Point  ed  buttons  and  move  among  the  items  with  the  Point  7  8  buttons,  and  then 
press SELECT button to fix. Move to the next row with the Point ed buttons to adjust.
4.  After  completing  all  the  settings,  select “Set”  and  press  SELECT  button.  Now,  all 
procedures  have  been  done. To  cancel  the  adjusted  settings,  select  "Cancel"  and  press 
SELECT button.  
You  can  confirm  the  LAN  settings  you  have  made  from “Network  information”  (p.14).  In 
such cases  that the LAN cannot be connected, see this screen.
Network setting
DHCP: On
Item  Description
DHCP  ....................  
Sets DHCP function On or Off. When you setup the network setting manually, select 
"Off ". When it is set On, IP address, Subnet, Gateway  and DNS are automatically set 
according to your network environment *
1.
IP address  .............Sets IP address of the projector
Subnet  .................... Sets Subnet mask. Normally sets 255.255.255.0
Gateway*
2  ............. Sets IP address of the default gateway (Router)
DNS*3  .......................   Sets IP address of the DNS server.
DHCP: Off
Network configuration
* The numerical value is a setting example. 
						

							14
Chapter 2 Setup Procedures
The Network PIN code is to restrict the access to the projector through the network.
After  setting  the  Network  PIN  code,  you  need  to  enter  it  to  operate  the  projector  via  the 
networks.
Network PIN code
Network information
1. Select "Network PIN code" in the Network menu, and press SELECT button. 
  The Network PIN code screen will appear.
2. Set the Network PIN code.
Set the figures with the Point  ed buttons and move to the next items with the Point  7 
8  buttons. Select “Set” and press  SELECT button to set. To cancel the preset Network PIN 
code, select “Cancel”. When you do not want to set the Network PIN code, set "0000".
It is recommended to set the Network PIN code if you use the projector via the networks.  
The  Network  PIN  code  can  be  set  also  through  the  networks.    See “3.  Basic  setting  and 
operation” ➔	“Initial setting” ➔	“Network PIN code setting” (p.23).
Select "Network information" in the Network menu and press Point   8 or  SELECT  button 
to  show  LAN  setting  environment  of  the  currently  selected  projector.  (The  description 
below is an example and different from what will be shown.)
Network PIN code
Network PIN code screen
* The numerical value is a setting example. 
						

							15
ENGLISH
 
AMX D. D.
Network factory default
Choose  “AMX  D.  D.”  in  the  Network  menu  and  press SELECT button, select ON or OFF to 
allow the projector to be detected by AMX Device Discovery.
For more details, visit http://www.amx.com/.
1. Select “Network factory default” in the Network menu and press SELECT  button.
2. A confirmation box appears and select "Yes" and then press SELECT  button.
3. Another confirmation box appears and select "Yes" and then press SELECT  button.
4.   All  the  wired  LAN  settings  will  go  back  to  the  factory  default  settings.  For  details,  refer  to 
“Wired LAN factory default settings” as shown in the table below.
Network factory default 
						

							16
Chapter 2 Setup Procedures
Wired LAN factory default settings
ParameterSettings
DHCP Off
IP ADDRESS 169.254.100.100
SUBNET MASK 255.255.0.0
GATEWAY ADDRESS 255.255.255.255
DNS ADDRESS 255.255.255.255 
						

							ENGLISH
17
ENGLISH
Chapter 3 
 Basic Setting and Operation3
Describes  basic  operations  and  settings  for  controlling  the  projec -
tor  by  using  the  web  browser.  It  is  required  that  computer  and 
projector  is  connected  to  the  network  and  the  network  address  is 
properly configured. 
						

							18
Chapter 3 Basic Setting and Operation
[2] Login
 
If  the  setting  page  has  set  the  password,  the  authentication  window  will  appear.  In  this 
case  type  "user"  onto  the User  Name  text  area  and  the  login  Network  PIN  code  onto 
the Password  text area and then click OK (Log in) button.
*  The entering User Name must be "user" and it can not be changed.
[Note]
  When accessing the projector for the first time or the Network 
PIN code "0000" is set, the auto-login will be performed and 
the next main setting page is displayed.
* The numerical value is a setting example.
Login the setting page of the projector
[1] Enter the IP address
      L aunch  the  web  browser  ins talled  in 
your computer, enter the IP address into 
the  "Address"  on  the  browser  and  then 
press "Enter" key.
      Enter  the  address  that  you  configured 
in  item  "Net work  configuration"  (
+ 
p .12 ). 
						

							19
ENGLISH
 
[3] Display of main setting page
The  following  main  setting  page  will  be  displayed  according  to  your  display  mode 
selection. Perform various kinds of settings through this page. Click on the menus to dis-
play the control and setting pages.
Main setting page in the display
Setting page
Displays the control and 
setting items according to 
the selected menu.Main menu
For selection of  control and 
setting items of the projector. 
Sub menu tab
Switches the sub 
menu tab.
Login the setting page of the projector 
						

							20
Chapter 3 Basic Setting and Operation
How to use the setting page
To control and set up the projector, use the setting menus on the web browser. Describes the 
basic operation and procedures commonly used on this manual.
The  setting  menu  appears  when 
clicking the sub menu tab. 
*  Each item has a valid setting range 
respectively.
Example of the setting page
✐		The value in the text box indicates current value.
✐    Each item has a valid setting range. The setting value exceeding this becomes invalid. Some con -
trol items can not be used depending on the selecting input mode or functions of the projector 
you use. In this case, the values of those items are indicated with "---".
Text box setting
Enter a number or text and then click Set button.
or 
Change a value with 
– or + button.
Pull-down menu setting
Select an item with pull-down menu 
button and then click Set button.
Types of setting