Eiki Projector EK-500U User Manual

							31
Adjustment pad
Keystone adjustment
Adjustable pad
You may use the adjustment leg to raise your pro
-
jector up to 5.0 degree.
Turn the pad to tilt your projector to required height. 
To raise your projector, turn both pads clockwise.
To lower down your projector or close the pad, turn 
both pads counterclockwise.
You may use the auto setup function to adjust your 
projector’s keystone distortion automatically or do 
this with the remote controller or OSD menu manu -
ally.
You may adjust keystone distortion of image in your pro -
jector with the V keystone adjustment.
Follow steps below to adjust keystone distortion of pro -
jected image manually.
Press the KEYSTONE button on your remote controller. 
The keystone adjustment dialog box displays, press 
  
button to adjust keystone distortion. You may save your 
settings for keystone adjustment.
Press 
 button to narrow upper part of the image 
Press  button to narrow lower part of the image 
Keystone adjustment 
 
● The arrow mark looks white when there is no keystone adjustment in exist\
ence. 
 
● The arrow mark indicating the adjustment direction turns red. 
 
● The arrow mark disappears when the maximum adjustment limit reaches. 
 
● The keystone adjustment will be canceled if you press the keystone adjus\
tment button when it is 
displaying. 
 
● The adjustable range is subject to source of signal input. Keystone 
adjustment  
Basic operation   
						

							32
Menu item overview
Main menuSubmenuDisplayAuto PC adj.                                 Fine syncH Position                                 V Position                                 
H size                             
Aspect                           
Project way                             
Menu position                                
Background display  
System 0
0
0
0
Normal Front
Upper left
Blue
- - - -
① ② ③④
⑤⑥
⑦
 Display
Select Auto PC Adjust, Fine sync., H Position, V Position, H size, Aspect, Project way, 
Menu position, Background display, System to align each parameter with VGA input 
signal format. 
 Color adjust
The color adjust options are: Image mode (Cinema/ Blackboard(Green)/ \
Colorboard/ 
User Image/ Dynamic/ Standard), Contrast, Brightness, Color temp., Red,\
 Green, Blue 
and sharpness.
 Setting
For computer input the setting options are: On start, Standby mode, High\
 land, Lamp 
control, Cooling fast, Key lock, Iris and Sound.
For video input the setting options are: On start, Standby mode, High la\
nd, Lamp con -
trol, Cooling fast, Closed caption, Key lock, Iris and Sound.
For HDMI input the setting options are: On start, Standby mode, High lan\
d, Lamp con -
trol, Cooling fast, Key lock, Iris, Sound and HDMI setup.
  Expend
Setting the Language, Auto setup (Input search/ Auto PC adj./ Auto keystone), Key-
stone, Logo, Security, Power management, Filter counter, Test pattern, Remote control 
and Factory default function as you need.
 Memory Viewer
Setting the display method of Memory Viewer page as Set slide, Slide transition effect, 
Sort order, Rotate, Best fit, Repeat and Apply. 
 Network
Network function menu.
 Information
Display information about the projector.
Basic operation   
						

							33
Main menu SubmenuDisplayAuto PC adj.                                 Fine syncH Position                                 V Position                                 
H size                             
Aspect                           
Project way                             
Menu position                                
Background display  
System 0
0
0
0
Normal Front
Upper left
Blue
- - - -
How to use the OSD
Menu operation
1.  Press the MENU button on the rear control 
panel or remote controller and the OSD 
displays.
2.  Press 
 button to act on or select one 
main menu item. Press  button or OK 
button to enter a submenu.
3.  Press 
 button to select required sub-
menu, then press OK button or  button to 
set up or enter an option.
4.  Press 
 button to select settings or 
navigate options, then press OK button to 
act on the item and exit.
5.  Press 
 button to return to mainmenu.  
Press the MENU button on remote control -
ler or control panel to exit the OSD.
 
OK 
Menu 
360.2
141.7VOL- VOL+AUDIO
AUDIO
IN2
AUDIO
IN1 AUDIO
OUT
S-VIDEO
VIDEO R/C
IN R/C
OUT
RS-232C
DVI-D
P/PR
MONITOR OUT
VGA 
ING/Y
B/PBH/HV V
Menu
OK 
 
Basic operation   
						

							34
Remote controller operation
Use your remote controller for common operations.
Screen size selection (SCREEN)
Press the SCREEN button on remote controller 
to select required screen size mode.
Digital Zoom (D.ZOOM+/-)
Press the D.ZOOM+/- button on remote con-
troller to enter the Digital Zoom mode. 
*Only for input as VGA, RGBHV, and the 
screen size setting as Normal or Wide. 
Volume +/- (VOLUME +/-)
Increase or decrease volume. 
Timer (TIMER)
Press the TIMER button on remote controller. 
A timer animation (00:00) displays and starts 
timing in format of (00:00-59:59).
Press the TIMER button again to stop timing. 
Press the TIMER button again to disable the 
timing function. 
02：02
Timer display 
Freeze (FREEZE)
Press the FREEZE button on remote control-
ler to freeze image on the screen. Press the 
FREEZE button or any button to cancel the 
freeze function. 
Blank (BLANK) 
Press the BLANK button on remote controller; 
a blank screen displays to replace existing 
image. Press the BLANK button or any other 
button to restore the image.
Press the BLANK to toggle switch your screen 
as shown below: 
BLANK → Normal → BLANK → Normal → ......
Volume +/- 
Screen 
D.Zoom +/- 
Timer  Blank  
Freeze
The BLANK screen disappears if no 
buttons are pressed in 4 seconds.
Blank ImageBLANK 
Basic operation  
						

							35
Input selection
Direct Operation
Press HDMI, VGA, VIDEO, D VI, C OMPON EN T, 
RGBHV, USB or S-VIDEO on the remote 
control as input source. When input source is from com-
puter connected to VGA ter-
minal with VGA cable,  please 
select "VGA".
When input source is from BNC 
connected to RGBHV terminal 
with BNC*5 cable,  please se-
lect "RGBHV".
 Note:
  -  When the "Input search" function is set to "On" in the "Auto setup" func\
tion, the input signal will  
    be searched automatically. Menu operation
1 Press INPUT button on the top control to 
   display the input select menu. 
2 Press 
 button to select VGA, RGBHV, 
HDMI 1, HDMI 2(MHL), DVI, Component, 
Video, S-viedo, Memory Viewer, Network or 
USB Display, then press the OK button.
Input select menuRemote control
RGBHV
When input source is from  
equipment connected to HDMI  
terminal with HDMI cable, 
please select "HDMI".
When input source is from  
equipment connected to HDMI  
terminal with HDMI cable, 
please select "HDMI 2".
When input source is from  
equipment connected to DVI  
terminal with DVI cable, please 
select "DVI".HDMI 1
HDMI 2(MHL)
DVI
ComponentSelect it when the input source 
is from the video equipment 
connected to YCbCr terminal.
Select it when the video input 
signal is connected to VIDEO 
IN terminal. Select it when the video input 
signal is connected to S-VIDEO 
IN terminal.
VGA
 Video
 S-video
Input select
Control Panel
VGA
RGBHV
HDMI 1
HDMI 2(MHL)
DVI
Component
Video
S-video
Memory Viewer
Network
USB Display
INPUT 
360.2
141.7VOL- VOL+AUDIO
AUDIO
IN2
AUDIO
IN1 AUDIO
OUT
S-VIDEO
VIDEO R/C
IN R/C
OUT
RS-232C
DVI-D
P/PR
MONITOR OUT
VGA 
ING/Y
B/PBH/HV V
S-VIDEO RGBHV 
DVI 
COMPONENT 
VIDEO 
HDMI  VGAPATTERN INPUT  
						

							36
Input selection
When input source is from 
network connected to LAN 
terminal with LAN cable, please 
select "Network". When input source is from 
device connected to USB-A 
terminal, please select "Memory 
Viewer".When input source is from   
device connected to Micro-USB 
terminal, please select "USB 
Display". Network
Memory Viewer
 USB Display
 Note:
  -  When the "Input search" function is set to "On" in the "Auto setup" func\
tion, the input signal will  
    be searched automatically.
  -  When signal is in "USB Display","Memory Viewer" and "Network", FREEZE, ASPECT, IMAGE, 
    AUTO SETUP and SCREEN function cannot work.   
Input select menu Remote control
Control Panel
VGA
RGBHV
HDMI 1
HDMI 2(MHL)
DVI
Component
Video
S-video
Memory Viewer
Network
USB Display
INPUT 
INPUT 
360.2
141.7VOL- VOL+AUDIO
AUDIO
IN2
AUDIO
IN1 AUDIO
OUT
S-VIDEO
VIDEO R/C
IN R/C
OUT
RS-232C
DVI-D
P/PR
MONITOR OUT
VGA 
ING/Y
B/PBH/HV V  
						

							37
DisplayAuto PC adj.                                 Fine syncH Position                                 V Position                                 
H size                             
Aspect                           
Project way                             
Menu position                                
Background display  
System 0
0
0
0
Normal Front
Upper left
Blue
- - - -
Input selectiong
System selection
The scanning system and auto computer adjustment function may detect scores of signal format.   
If a PC is selected as the input signal source, your projector will detect and adapt to its signal for-
mat automatically. Correct image can be displayed without any setup operation. 
Your projector will display one of the following: 
Auto
-----
If your projector failed to identify 
signals not shown in the signals 
format table, the “Auto” message 
will display in the System Signal 
Format  menu. The Auto  PC Ad-
justing function will make neces -
sary adjustment to your projector 
to project valid images. If images 
are displayed incorrectly, adjust it 
manually. 
No PC signals detected. Check 
the connection between PC and 
your projector.  OSD menu 
The selected system displays in the 
PC system menu. 
Select the computer system manually. 
1   Press the MENU button on remote control-
ler and the OSD displays. Press 
 button 
to point to the Display icon, press  button 
or OK button and the Display menu dis-
plays. 
2  Press 
 button to select System Signal 
Format, then press OK button.
3 Press 
 button to select required system 
signal format, then press OK button to con-
firm your selection. 
 Note: 
Your projector may save data gen -
erated by the Auto PC Adjusting 
function. 
 Note: 
The computer system menu will be disabled once HDMI or DVI has been sele\
cted.   
						

							38
OSD Setting-Display
Auto  PC Adjusting
The Auto PC Adjusting function may get Total Dots, Horizontal and Vertical position, Display area H, 
and Display area V aligned with computer input. Menu Operation
1  Press the MENU button on remote controller 
and the OSD displays. Press 
 button to 
select Display icon. Press  button or OK 
button and the Display menu displays. 
2 Press 
 button to point to Auto PC Adj. op-
tion, press OK button to confirm your choice. 
 Note: 
 
● Fine sync, H and V position and H Size of certain computers may be fully\
 adjusted by the 
Auto PC Adjusting function. In case the post-adjustment image still looks incorr\
ect, adjust 
it again manually.
 
● The Auto PC Adjusting function will be disabled once 480i, 575i, 480p, 575p, 720p, 1\
035i 
or 1080i has been selected in the system menu. 
DisplayAuto PC adj.                                 Fine syncH Position                                 V Position                                 
H size                             
Aspect                           
Project way                             
Menu position                                
Background display  
System 0
0
0
0
Normal Front
Upper left
Blue
- - - -
Display
Auto PC adj.                                 Fine syncH Position                                 V Position                                 
H size                             
Aspect                           
Project way                             
Menu position                                
Background display  
System 0
0
0
0
Normal Front
Upper left
Blue
- - - -
Direct Operation
Press Auto button on the remote control to 
launch the Auto PC Adj. function.
AUTO  
						

							39
Manual computer adjustment
The scan system of your projector may fail to detect signal format used \
by certain computers as 
they opted some special signal format. The manual computer adjustment function of your projector 
enables you to adjust individual parameter to align with most special si\
gnal format. Your projector 
comes with up to storage area to keep parameters manually adjusted by yo\
u. You may save pre-
ferred settings for certain computers as required. 
1  Press MENU button on the remote controller and the OSD displays. Press 
 button to select 
Display icon, press  button or OK button to confirm your selection. 
2 Press  button to select items for adjustment, press  button or OK button to confirm your 
selection. Press  button to adjust settings.
Auto PC adj.
Adjust [Fine sync], [H Position], [V Position] and [H 
Size] automatically.
Fine Sync
Eliminate flashes in image. Press   
 button to adjust 
Total Dots. 
H Position
Press  
 button to adjust horizontal position of 
image. 
V Position
Press  
 button to adjust vertical position of image. 
H size
Adjust and minimize the effect of interference caused 
by projection of patterns consisting of vertical stripes. 
Aspect
Press 
  button to select the item to set the screen 
size  to  fit  the  image  while  maintaining  the  aspect  ratio 
of the input signal.
Normal...    Projects the image at the maximum size while 
maintaining the aspect ratio of the input 
signal.
Wide.... Projects the image at 16:9 aspect ratio.
DisplayAuto PC adj.                                 Fine syncH Position                                 V Position                                 
H size                             
Aspect                           
Project way                             
Menu position                                
Background display  
System 0
0
0
0
Normal Front
Upper left
Blue
- - - -
DisplayAuto PC adj.                                 Fine syncH Position                                 V Position                                 H size                             Aspect                           Project way                             Menu position                               Background display  
System
0
0
0
0
Normal Front
Upper left
Blue
- - - -
OSD Setting-Display  
						

							40
DisplayAuto PC adj.                                 Fine syncH Position                                 V Position                                 
H size                             
Aspect                           
Project way                             
Menu position                                
Background display  
System 0
0
0
0
Normal Front
Upper left
Blue
- - - -
DisplayAuto PC adj.                                 Fine syncH Position                                 V Position                                 H size                             Aspect                           Project way                             Menu position                               Background display  
System
0
0
0
0
Normal Front
Upper left
Blue
- - - -
 Note: 
 
● The Fine Sync, Total Dots and Clamp function will be disabled if 480i, 576i, 480p, 576p,\
 
720p, 1035i or 1080i has been selected in the system menu.
OSD setting-Display
Project way
Press  button to select the project way.
Front ........   Projects to front screen when projector is 
front standing.             
Rear ........    Projects to rear screen when projector is 
front standing.
Ceiling/Front .....   Projects to front screen when 
projector is in ceiling state.   
Ceiling/Rear .....    Projects to rear screen when 
projector is in ceiling state.
Auto Ceiling/Front:   Projects to front screen when 
projector is in ceiling state 
automatically.   
Auto Ceiling/Rear:   Projects to rear screen when 
projector is in ceiling state 
automatically.
Menu position
Press  button to select the position of the on 
screen menu .
Upper left .... Menu locates on upper left of 
                      the screen.
Upper right .. Menu locates on upper right of 
                      the screen.
Center ......... Menu locates at the center of 
                      the screen.
Lower left .... Menu locates on lower left of 
                      the screen.
Lower right .. Menu locates on lower right of 
                      the screen. 
Background display
Press   button to select thescreen background of 
the projector when there is no signal detected .
Black .... Select black background.
Blue ...... Select blue background.