Eiki Projector EK-300U User Manual

51
    (3) When DHCP is set On, IP address, Subnet, 
         Gateway and  DNS will be obtained 
         automatically, press the OK at "Set" to confirm 
         the parameters.
         When DHCP is set Off, press the OK button to 
         enter IP address, then press  button to enter 
         Subnet, Gateway and DNS respectively, 
         press the OK at "Set" to confirm the parameters.
       
Expand
  Note:
    See page 54 for usage of Network.
This function returns all setting...

52
Memory viewer
The Memory Viewer function makes it possible to project the pictures which are store\
d in the USB 
memory when the USB memory is inserted into the projector
Start the slide show. Note:
● The "Memory Viewer" menu is available 
   when select the input source as "Memory  
   Viewer".
● All the setting except "Set Slide" will effective 
   after execute "Apply".
● See page 62  for Memory viewer function.
Memory Viewer menu
Set the slide transition effect...

53
Information
The information menu is used to the detect signal of projected image and\
 running state.
Menu operation
Press MENU button on the remote control or 
top control to display the screen menu. Press 
  to select  Info., the information menu will 
appear as the right picture.
The information below will display in 
information menu. info. menu
Info.
Input
H-sync freq.
V-sync freq.
Lamp status
Lamp counter
Power management
Image modeComputer 1
1024 x 768, 60Hz 48.24   kHz
60.06     Hz
2...

54
LAN control
Function : PC controls projector via LAN.Preparation:
1. Equipments: PC, projector, cables
2. Connection procedures:
    Connect the projector to routers or switches of the LAN by direct or\
 cross cable. If it fails to  
    connect PC and projector by parallel cable, please switch to cross c\
able as suggested.
3. After the computer is booted and the projector is plugged in, indicator \
lights of LAN interface 
    and computer interface will flash continuously.
Operation procedures:...

55
Network Control Instructions
6. Select "Login" to login the Network Display System page. (Both the i\
nitial name and passwords 
    are "admin".)  Note:
●  You can click the upper right corner of the web browser screen to select the display language.
●  Do not perform setting or control simultaneously by starting up multiple web browsers. Do not 
    set or control the projector from multiple computers.
●  Change the password first. (8 half-width characters). 
●  If the screen for...

56
Network Control Instructions
"System Status" page
  Display the status of the projector for the following items."General Setup" page
 Change Password for Webpage is displayed.
①
②
③
①
②
③④
⑤
⑥
①  Model Name
     Displays the model No. of the projector.
②   Versions
     Displays the version of the firmware of the 
     projector.
①  Enter Old password
     Enters the configured password.
②  Enter New password
     Enters the new password.
③  Confirm New password
     Enters the wanted...

57
"Picture Setup" page
① Brightness
     Adjusts the brightness of the projected image.
②  Contrast
     Adjusts the contrast of the projected image.
③  Sharpness
     Adjusts the sharpness of the projected image. ④
 Color
     Adjusts the color saturation of the projected  
     image.
⑤  Tint
     Adjusts the skin tone of the projected image.
⑥  Color Temperature
      Adjusts the color temperature of the projected 
     image.
①
②
③
④
⑤
⑥
Network Control Instructions  

58
"Image Setup" page
①
②
③
④
⑤
⑥
⑦
⑧
⑩⑨
⑪
①    Aspect
     Switches the aspect of the projected image.
②  Fine sync
     Adjusts the fine sync of the projected image.
③  H Position
     Adjusts the horizontal position of the projected 
     image.
④   V  Position
     Adjusts the vertical position of the projected 
     image.
⑤  H.Size
     Adjusts the total number of dots of the 
     projected.
⑥  Freeze
     Switches the freeze function between on 
     and off. ⑦ 
Auto PC adj.
    Executes...

59
"Network Setup" page
8. PwPresenter software: when "Network" is selected in Source Select, yo\
u can project the current 
    computer images via network.   
  
   Input the IP address of the projector in webpage to enter the Network Display System\
, click  
   "Download" to download the PwPresenter software according to your ope\
ration system.
① LAN Setup
     Select [Obtain an IP address automatically]  
     if you want to enable the DHCP client.
      IP Address...

60
① Search for projector display    Click to enter Search, select the projector and connect it. Please setti\
ng the same IP address of 
    the projector in pwPresenter software, (such as: 192.168.1.100).  \
Both the initial name and 
    passwords are "admin".
 Note:
●  Before use PwPresenter software to search, you need change Source Select\
 to "Network".
②  Play/Pause
    Play or pause the selected image.
③  Choose capture mode
    Choose a capture mode from "FullScreen",...