Eiki Projector Eip S200 User Manual

EN-20
Position the projector in a horizontal position; other positions can cause
heat build-up and damage to the projector.
Make sure the heat ventilation holes are not blocked.
Do not use the projector in a smoky environment. Smoke residue may
cause buildup on critical parts.
33.34(Min.)
55.56
83.35
138.9
277.8
(Max.)
259.62
129.8177.8951.93
31.1
1.2m
3.0m
5.0m
10.0m 2.0m
A
B
A:B=8.3:1.2
PROJECTION
DISTANCE (METER)
4:3 SCREEN SIZE-
DIAGONAL (INCH)
Wide
Tele
1.2
33.34 31.12.0
55.56
51.93 3.0
83.35
77.89...

EN-21
Menu Operation
The projector has multilingual On Screen Display menus that allow you to make image
adjustments and change a variety of settings. 

EN-22
How to operate
1. Press Menu button to open the OSD menu.
2. When OSD is displayed, use  W / X  buttons to select any feature in the main menu.
After selecting the desired main menu feature, press  T button to enter sub-menu
for feature setting.
3. Adjust the settings with  W / X  buttons.
4. To return to the main menu, press  Menu button.
5. To exit OSD, press  Menu button. The OSD menu will close and the projector will
automatically save the new settings. 

EN-23
Image (Computer / Video Mode)
Contrast
The contrast controls the degree of difference between the lightest and darkest parts
of the picture. Adjusting the contrast changes the amount of black and white in the
image.
QPress W to decrease the contrast.QPress  X to increase the contrast.
Brightness
Adjusts brightness of the image.
QPress  W  to darken the image.QPress  X  to lighten the image.
Keystone
Adjusts image distortion caused by tilting the projector.
Aspect Ratio
Use this function to choose...

EN-24
Red
Manually adjusts red.
Green
Manually adjusts green.
Blue
Manually adjusts blue.
Video (Video Mode)
Saturation
Adjusts a video image from black and white to fully saturated color.
QPress W to decrease the amount of color in the image.QPress  X to increase the amount of color in the image.
Tint
Adjusts the color balance of red and green.
QPress  W to increase the amount of green in the image.QPress  X to increase the amount of red in the image.
Sharpness
Adjusts the sharpness of the image....

EN-25
Audio (Computer / Video Mode)
VolumeQPress W to decrease the volume.QPress  X to increase the volume.
Mute
QChoose “ON” to turn mute on.QChoose “OFF” to turn mute off.
Language (Computer / Video Mode)
Choose the multilingual OSD menu. Use  S / T  to select your preferred language. Press
“ W  / X  / Enter ” to finalize the selection.
Advanced (Computer / Video Mode)
Auto Source Select
Automatically scans the input source. Press “ W / X  / Enter ” to confirm or cancel the
selection.
Rear
The image...

EN-26
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt
or spots will project on the screen and diminish image quality. If any o\
ther parts need
replacing, contact your dealer or qualified service personnel. When cleaning any part
of the projector, always switch off and unplug the projector first.
Warning:
Never open any of the covers on the projector. Dangerous electrical voltages inside
the projector can cause severe injury. Do not attempt to service...

EN-27
Replacing the Lamp
Projector lamps have a finite life. Replace the lamp when:
JThe image becomes darker and hues become weaker after a lamp has been for a
long period of time.
JThe projector lamp LED indicator turns into amber. Refer to section titled “LED
Indicator Messages”   (p.30) for further details.
JThe lamp becomes high temperature after turning off the projector with t\
he
power button. If you touch the lamp, you may scald your finger. When you\
replace the lamp, wait for at least 45...

EN-28
1. Turn off the projector and unplug the AC powercord.
Allow the projector to cool for at least 45
minutes.
2. Place a protective sheet (cloth) beneath the projector. Turn the projector over so you can
access the lamp cover.
3. Loosen the screws on the lamp cover and open it.
4. Loosen the screws on the bottom of the lamp assembly.
5. Grasp the lamp handle and pull the lamp assembly
directly out of the projector.
6. Replace with the new lamp.
7. Tighten the screws on the bottom of lamp assembly....

EN-29
Specifications
Display Type Single 0.55 DLP panel
Resolution (Pixels)800 x 600
Uniformity 85%
Lens Manual Zoom (1.07x)
F=2.4 6mm
f=19 .91- 21.36mm
Contrast Ratio2000 : 1
Aspect Ratio 4:3 (Default) , 16:9
Screen Size 31.1 - 277.8
Throw Distance1.2m - 10m
Lamp 200W
Projection Type Front, Rear, Ceiling
Video CompatibilityNTSC4.43
PAL-60, PAL-M,N,(B,D,G,H,I )
SECAM
Input Source D-Sub 15 pin, S-Video, Composite Video, Stereo Phone
Jack, RS232, USB
Scanning Frequency Horizontal Frequency 31 - 79 KHz...