Digital Projection Projector M-Vision 930 3D Series User Manual

							page 13
Installation and Quick-Start Guide
CHANGING THE LENS
Removing the lens
1. Push the button 1 all the way in.
2. Rotate the lens counterclockwise 2 until it disengages.
3. Slowly pull the lens out 3.
Notes
 Before changing the lens, 
always make sure the projector 
is switched off and fully 
disconnected from its power 
supply.
 When changing the lens, avoid 
using excessive force as this may 
damage the equipment.
  Take care to preserve the original 
lens packaging and protective caps 
for future use.
132
   
Digital Projection M-Vision 930 Series 
Rev C Februar y 2015  
						

							page 14
Installation and Quick-Start Guide
CHANGING THE FILTERS
Changing The Filters
The projector contains four identical replaceable filters accessible via the air inlets.
To replace the filters on the right-hand side of the projector:
1. Loosen the two screws on the cover of the air inlet and remove the cover\
.2. Pull out the old filters.
3. Insert the new filters into the slots.4. Reattach the cover and tighten the screws.
Notes
 Before changing the filters, 
always make sure the projector 
is switched off and fully 
disconnected from its power 
supply.
 When changing the filters, avoid 
using excessive force as this may 
damage the equipment.
   
Digital Projection M-Vision 930 Series 
Rev C Februar y 2015  
						

							page 15
Installation and Quick-Start Guide
CHANGING THE FILTERS
To replace the filters on the left-hand side of the projector:
1. Loosen the three screws on the cover of the air inlet and remove the cov\
er.2. Pull out the old filters.
3. Insert the new filters into the slots.4. Reattach the cover and tighten the screws.
Notes
   
Digital Projection M-Vision 930 Series 
Rev C Februar y 2015  
						

							page 16
Installation and Quick-Start Guide
CHANGING THE LAMPS
Changing The Lamps
1. Remove the lamp cover (Fig. 1).
2. Loosen the screws of the lamp modules (Fig. 2).
3. Pull the lamp modules out of the enclosures (Fig. 3).
Fig. 1
Fig. 2
Fig. 3
Notes
  Before removing the lamp 
modules for replacement, turn 
off the projector and unplug the 
power cord.
  Let the projector cool for 
approximately 60 minutes.
   
Digital Projection M-Vision 930 Series 
Rev C Februar y 2015  
						

							page 17
Installation and Quick-Start Guide
CHANGING THE LAMPS
4. Insert the new lamps (Fig 4).
5. Replace the lamp covers (Fig. 5).
6. Firmly secure the screws on the lamp covers (Fig. 6).
Notes
Fig. 4Fig. 5
Fig. 6
   
Digital Projection M-Vision 930 Series 
Rev C Februar y 2015  
						

							page 18
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Operating The Projector
Switching the projector on
1. Connect the power cable between the mains supply and the projector. Switch on at the switch next to the power connector.
Wait until the self-test has completed and the STANDBY indicator on the projector control panel shows amber. The system will be off and 
the projector will be in STANDBY mode.
2. Press ON on the remote control or STBY on the control panel to switch the projector on. The ON indicator on the control panel flashes 
blue for a few seconds while the lamp comes up to full brightness.
Switching the projector off
1. Press OFF on the remote control or STBY on the control panel, then press the button again to confirm.
The lamp will switch off, the ON indicator on the control panel will start flashing blue and the cooling fans will run for a short time until the 
projector enters STANDBY mode.
2. If you need to switch the projector off completely, switch off at the mains power switch next to the power connector and then disconnect 
the power cable from the projector.
Notes
 See also Connecting The Power 
Supply  earlier in this guide.
 The self-test is running when all the 
LEDs on the control panel are lit.
 Use only the power cable 
provided.
 Ensure that the power outlet 
includes a ground connection as 
this equipment MUST be earthed.
 Handle the power cable carefully 
and avoid sharp bends. Do not 
use a damaged power cable.
   
Digital Projection M-Vision 930 Series 
Rev C Februar y 2015  
						

							page 19
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Selecting an input signal or test pattern
Input signal
• Connect an image source to the projector. The signal should be automatically detected by the projector, and should be displayed within 
two or three seconds.
• If more than one signal is connected, then select the input you want to display:
• Press one of the input buttons on the remote control, or
• Open the On-screen display (OSD) by pressing MENU. Highlight Input from the main menu, press ENTER/SELECT and then select 
an input signal using the UP and DOWN arrow buttons. Press ENTER/SELECT to confirm your choice.
Test pattern
To display a test pattern:
• Open the OSD by pressing MENU. Highlight Test Patterns from the main menu, then select a test pattern using the LEFT and RIGHT 
arrow buttons.
Notes
 For full details of how to use the 
controls and the menu system, see 
the Operating Guide .
   
Digital Projection M-Vision 930 Series 
Rev C Februar y 2015  
						

							page 20
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Adjusting the lens
The lens can be adjusted using the Lens menu, or using the LENS button on the 
remote control.
The LENS button opens the Lens Control setting, which adjusts zoom, focus 
and shift. The Lens menu gives you access to the Lens Control setting and the 
Lens Center command.
Lens Control allows you to adjust Zoom, Focus and Shift using the arrow 
buttons. The setting operates in Zoom/Focus Adjustment and Shift Adjustment 
mode.
Press ENTER/SELECT to switch between modes as follows:
• Zoom/Focus Adjustment mode with the source 
image
• Shift Adjustment mode with the source image
• Zoom/Focus Adjustment mode with an 
alignment grid
• Shift Adjustment mode with an alignment grid
• Zoom/Focus Adjustment mode with an aspect 
test
• Shift Adjustment mode with an aspect test
• Zoom/Focus Adjustment mode with a screen 
layout pattern1.60:1 (16:10)
1.66:1
1.78:1 (16:9)
1.85:1
1.33:1 (4:3)
2.35:1
• Shift Adjustment mode with a screen layout 
pattern
...
LensControl
[Enter] ShiftAdjustment
Zoom
Focus
Lens Control
[Enter] Zoom/Focus Adjustment
Shift
Notes
   
Digital Projection M-Vision 930 Series 
Rev C Februar y 2015           
						

							page 21
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Adjusting the image
Orientation
• This can be set from the Setup menu.
Highlight Orientation and choose from Desktop Front, Ceiling Front, Desktop Rear and Ceiling Rear.
Keystone
• This can be set from the Geometr y menu.
Picture
• Settings such as Brightness, Contrast and Gamma can be set from the Image menu.
• You can also set Brightness, Contrast or Gamma by pressing BRIGHTNESS, CONTRAST or GAMMA on the remote control.
Notes
Setup menuOrientation
Geometr y menu Keystone
Image menu
   
Digital Projection M-Vision 930 Series 
Rev C Februar y 2015  
						

							Installation and Quick-Start Guide
   
Digital Projection M-Vision 930 Series 
This page is intentionally left blank.