Dell Sp2309w Users Guide

							OSD Warning Messages    
 
Select  Yes  to disable DDC/CI or  No  to return.  
 
LCD Conditioning   LCD conditioning helps eliminate any image retention and may take several hours.  
NOTE:   Severe cases of image retention are known as burn - in. LCD Conditioning does not remove burn - in.  
Disable : This is the default option.  
Enable : Enables LCD conditioning and the following message appears on the screen. Select  Yes  to proceed and  No  to return.
   
  
 NOTE:   Touch any key on the monitor to terminate LCD Conditioning at any time.   
 
Factory Reset   Resets all OSD settings to the factory preset values.  
  Personalize  
 
Allows you to adjust shortcut key key for: 1. Brightness & Contrast, 2. Input Source, and 3. Preset mode.  
The following warning messages may appear on the screen to indicate that the monitor is out of synchronization.
 
 
This means that the monitor cannot synchronize with the signal that it is receiving from the computer. Either the signal is too high or too low 
for the monitor to use. See  Specifications  for the Horizontal and Vertical frequency ranges addressable by this monitor. Recommended mode 
is 2048 X 1152 at 60Hz.   
						

							See  Solving Problems  for more information.  
Setting the Optimal Resolution  
To set the optimal resolution for the monitor:  
1. Right - click on the desktop and select  Properties .   
2. Select the  Settings  tab.   
3. Set the screen resolution to 2048 x 1152.   
4. Click  OK .   
If you do not see 2048 x 1152 as an option, you may need to update your graphics driver. Depending on your computer, complete one of the following 
procedures:  
l If you have a Dell desktop or portable computer: 
Go to  support.dell.com , enter your service tag, and download the latest driver for your graphics card.   
l If you are using a non - Dell computer (portable or desktop):
Go to the support site for your computer and download the latest graphic drivers.   
Go to your graphics card website and download the latest graphic drivers.   
Using the Dell Soundbar (Optional)  
The Dell Soundbar is a stereo two channel system, mountable on Dell Flat Panel Displays.  The Soundbar has a rotary volume and on/off control to adjust the 
overall system level, a LED for power indication, and two audio headset jacks.  
 
Using the Tilt, Swivel, and Vertical Extension   
If you touch any key other than the Power Control (Touch Sensor) one of the following messages will appear depending on the selected 
input:
 
When monitor enters Power Save mode, the following message appears :  
1. Power/volume control
2.  Power indicator
3.  Headphone connectors   
						

							Tilt/Swivel  
With the built - in pedestal, you can tilt and/or swivel the monitor for the most comfortable viewing angle.  
 
Before you rotate the monitor, your monitor should be fully extended vertically ( Vertical Extension ) and fully tilted ( Tilt ) up to avoid hitting the bottom edge of 
the monitor.   
Adjust the Tilt  
  1. With the monitor still in its flat, folded state, set it screen - side up on a flat surface.
  2. Adjust the tilt by moving the edges of the monitor either toward or away from you, without 
touching or putting touchure on the screen.
 
CAUTION: - hinged monitor can fall back if the hinge is extended fully and the monitor 
screen is tilted back too far.  
  1. Put the shipping strap in a safe place, in case you need it to ship the monitor.
  2. Lift and lower the base hinge for proper viewing.
 
     
NOTE:   The base of stand is attached when the monitor is shipped from factory.   
						

							 
 
Vertical Extension  
This Vertical Extension function can help you adjust the monitor for the most comfortable viewing height. You can push the top edge or pull the bottom edge of 
the monitor carefully to adjust the position.  
 
   
Using the Camera   
Installing the Dell Webcam Software (Microsoft   Windows   Operating Systems)  
The Dell  SP2309W  webcam application media that ships with your monitor, allows you to install the software and drivers for the integrated webcam.   
To install the  Dell Webcam Software :  
You are now ready to use the Webcam.  
    NOTE:   To use the Display Rotation function (Landscape versus Portrait view) with your Dell computer, you require an updated graphics driver that is not 
included with this monitor. To download the graphics driver, go to  support.dell.com  and see the Download section for Video Drivers for latest driver 
updates . 
1. Insert the Dell  Drivers and Documentation  CD into the drive.
NOTE:  Ensure that the USB cable is connected between the monitor and the computer. 
2.  Choose  Webcam Software .
3.  The  Install Shield Wizard  automatically launches the setup application. Select the  Language  and click  Next  to continue.
4.  Read  Software License Agreement  and click  Yes  to continue.
5.  Click  Browse  to change  Destination Folder  where the software will be installed to and then click  Next  to continue.
6.  Choose  Full Installation  than click  Next  and follow the instructions to complete the installation. Alternatively, choose  Custom Installation  to select the 
components to install.
7. Click  Finish  to restart the computer after installation completes.   
						

							   
Accessing the Camera Help File  
To access the camera ’ s help file, right - click the Dell Webcam Central icon in the notification area and click. Click  Help  from the menu and select  Contents .  
   
 
Manually Adjusting the Camera Settings  
If you do not want the camera to use automatic settings, you can manually   adjust the camera settings.  
Setting the Contrast, Brightness, and Volume  
To set the contrast, brightness and volume:  
Right - click the  Webcam Central  icon in the system tray located in the lower right corner of the screen. Click Open Webcam Central.  
In the Webcam Console window:  
Click the  Settings  icon and navigate to  Settings  -  Picture Control . Adjust video settings, such as contrast and brightness.  
Click the  Effects  icon and navigate to  Effects  -  Avatars . Adjust audio settings, such as volume level.  
For more information about camera settings and other camera - related topics, see the camera ’ s Help file (see  Accessing the Camera ’ s Help File ).  
Setting the Resolution  
To set the camera resolution using the  Dell Webcam Central :  
Resetting the Camera Defaults    
To reset the  Camera  settings using the  Dell Webcam Central :  
1. Right - click the  Dell Webcam Central  icon in the system tray located in the lower right corner of the screen. Click  Open Webcam Central .   
2. In the Webcam Central window:  
-  Click the  Settings  icon and navigate to  Settings  -  Picture  Control. Click  Restore Default .      
Back to Contents Page  1. Right - click the  Dell Webcam Central  icon in the system tray located in the lower right corner of the screen.   Click  Launch Webcam Center .   
The Dell Webcam Center window appears. 
2. Click the  Record Video  tab. 
3. Configure settings by clicking the  More Options  key located at bottom center of the preview window. Click the Video Size box and select the size that you want. 
4. Click the  Snap Photo  tab. 
5. Configure settings by clicking the  More Options  key located at bottom center of the preview window. Click the Photo Size box and select the size that you want.  
						

							Back to Contents Page   
Setting Up Your Monitor   
 
SP2309W  Flat Panel Monitor  
Setting the display resolution to  2048 x 1152  (Optimal)  
For optimal display performance while using the Microsoft Windows operating systems, set the display resolution to 2048 x 1152 pixels by performing the 
following steps:  
1. Right - click on the desktop and click  Properties .  
2. Select the  Settings  tab.  
3. Move the slider - bar to the right by pressing and holding left - mouse key and adjust the screen resolution to  2048 X1152 .  
4. Click  OK .  
    If you do not see  2048 x 1152  as an option, you may need to update your graphics driver. Please choose the  scenario below that best describes the 
computer system you are using, and follow the provided directions:  
1:   
2:   
Back to Contents Page     
						

							SP2309W  
Information in this document is subject to change without notice.  
2008 -  
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.   is strictly forbidden.  
Trademarks used in this text:  DELL  and the  DELL  logo are trademarks of Dell Inc;   Microsoft, Windows,   and  Windows Vista  are either registered trademarks or trademarks of 
Microsoft Corporation in the United States and/or other countries.  
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any 
proprietary interest in trademarks and trade names other than its own.  
Model SP2309Wc  
 
July 2009 Rev. A02  User Guide  
 
Setting the display resolution to 2048 x 1152 (optimal)  
     
						

							Back to Contents Page    
Setting Up the Monitor   
SP2309W  Flat Panel Monitor Users Guide  
   Unfolding the double - hinged monitor  
   Connecting the Monitor  
   Organizing Your Cables  
   Attaching the Soundbar (Optional)  
   Wall - Mounting the Monitor(Optional)    
Unfolding the double - hinged monitor  
Connecting Your Monitor  
To connect your monitor to the computer:  
1. Turn off your computer and disconnect the power cable.   
2. Connect the HDMI cable, white (digital DVI - D), or blue (analog VGA) display connector cable to the corresponding video port on the back of your 
computer. Do not use all the cables on the same computer.  Use all of the  cables only when they are connected to different computers with appropriate 
video systems.   
Connecting the Blue VGA Cable  WARNING: - hinged monitor face down for folding.  
The base hinge can spring up and cause serious injury or damage.  
1. With the monitor still in its flat, folded state, set it screen - side up on a flat surface.
2.  Tilt the panel toward you without touching or putting pressure on the screen.
 
3.  Remove the shipping strap (do not cut it; do not flip the display to remove).
 
4.  Put the shipping strap in a safe place, in case you need it to ship the monitor.
5.  Lift and lower the base hinge for proper viewing.
CAUTION:  Before you begin any of the procedures in this section, follow the  Safety Instructions .    
						

							 
Connecting the White DVI Cable  
 
Connecting the HDMI Cable  
 
   
Connecting the USB Cable  
After you have completed connecting the DVI/VGA cable, follow the procedure below to connect the USB cable to the computer and complete your monitor 
setup:  
1. Connect the upstream USB port (cable supplied) to an appropriate USB port on your computer.   
2. Connect USB peripherals to the downstream USB ports (side or bottom) on the monitor. (See  side  or  bottom  view for details.)   
3. Plug the power cables for your computer and monitor into a nearby outlet.   
4. Turn on the monitor and the computer.  
If your monitor displays an image, installation is complete. If it does not display an image, see  Solving Problems .    
5. Use the cable holder on the monitor stand to organize the cables.   NOTE:  The graphics are used for the purpose of illustration only. Appearance of the computer may vary.  
						

							Organizing Your Cables  
 
 
After attaching all necessary cables to your monitor and computer, (see  Connecting Your Monitor yfXVHWKHFDEOHPDQDJHPHQWVORWWRRUJDQL]HDOOFDEOHVDV 
shown above.  
Attaching the Soundbar(optional)  
 
To attach the soundbar:  
Wall - Mounting the Monitor (Mounting Fixture not Supplied)  
Refer to the  instructions that come with the base mounting kit. To convert your LCD display from a desk - mounted to a wall - mounted display, do the following:  
1. Verify that the Power Control (Touch Sensor) is turned Off, then disconnect the power cord.   
2. Lay the LCD display face down on a towel or blanket.   
3. Remove the Plastic Covers from the back of the LCD display.   
4. Remove the four screws attaching the base (Screw dimension: M4 x 10mm).   
5. Remove the Rubber Plugs from inside the four VESA screw holes.   
6. Attach the mounting bracket from the VESA compatible wall mounting kit (100 mm x 100 mm distanceyf   
7. Attach the LCD display to the wall, following the instructions in the wall - mounting kit.   NOTICE:  Do not use with any device other than the Dell Soundbar. 
1.  Working from the back of the monitor, attach Soundbar by aligning the two slots with the two tabs along the bottom of the monitor.
2.  Slide the Soundbar to the left until it snaps into place.
3.  Connect the Soundbar with the DC power connector from the Soundbar Power Adaptor.
4.  Insert the mini stereo plug from the back of the Soundbar into the computers audio output jack.
Before you mount the monitor on a wall, a swing arm, or other mounting fixture, you must remove the base and the 
pedestal. You will need a Phillp ’ s screwdriver. Read the following warning and caution statements before beginning 
the procedure. 
  WARNING:   To reduce the risk of personal injury or of damage to the equipment, check that the wall - mounting fixture 
is adequately installed and secured before attaching the monitor. Refer to the instructions supplied with the wall -
mounting fixture and check that it is capable of supporting the monitor. 
  Preparing the double - hinged monitor for wall - mounting  
WARNING: - hinged monitor face down for folding.   
The base hinge can spring up and cause serious injury or damage.  
NOTE:   For use only with UL Listed Wall Mount Bracket with minimum weight/load: 2.05lbs (4.44kg) .