Daewoo Dwd Ld1412 Instruction Manual

							E-21
Washing procedure and program selection (cont.)
NOTE  
 •  
All programs are not selectable.
1Press the Power button.
•  The LED shows only ‘---’ signal.
2Select the ‘Drain’ program using program selection dial.
3Press Start/Pause button.
 •   Drain program will start.
* DRAIN PROGRAM
 
						

							E-22
Guide for other useful programs
NOTE  
 •  
If you want to check the selected program, press the ‘Start/Pause' button again.
 • Preparing washing before starting 'Time Delay';
    - Turn on the water tap.
    - Load laundry and close Door.
    - Place the detergent and fabric softner in the detergent case.
 •  
The actual time of finishing is a little different with your selecting time because of water supply condition and 
selected water temperature,....
 • 'DELICATE', 'Quick 20', 'Tub Clean' and 'Drain' program are not selected with 'Time Delay'.
 • Adding clothes during 'Time Delay' operation is not allowed.
1
Put the laundry into the Drum and put the detergent and softerner into the detergent
case.
Then close the Door.
•  
Put the detergent into the main wash room(I I marking) and prewash room(I marking) 
in the detergent case.
• Softener should be below ‘MAX' level.
• Put the detergent into the pre wash room(I marking) only if you want to add prewash.
•  
When you want to use bleach, put it into the main wash room (I I marking) with 
detergent.
2Press the Power button.
• The LED shows only ‘- --' signal.
3
Select the program by press the Delay Start button.
•  
If you press ‘Start/Pause' button aftrer pressing Power button without selecting 
program, the ‘NORMAL' program is selected as default program.
•  
Select the ‘Washing course' and ‘Spin speed' and 'water temperature' by pressing 
each corresponding button.
• The ‘Time Delay' LED is to be lighting.
• Select the time delay time you want from 1 hour to 12 hours by pressing button.
• The displayed time shows program finishing time.
4Press the 'Start/Pause' button.
• If you make this program successfully, only 'Time Delay' and 'Lock' LED are lighting.
* DELAY START(RESERVED WASHING)
 
						

							E-23
Guide for other useful programs (cont.)
1
Put the laundry into the Drum and put the detergent and softerner into the detergent
case.
Then close the Door.
2Press the Power button.
• The LED shows only ‘- --' signal.
3Select the ‘WASH COURSE' you want by pressing ‘Wash' button.
• The water temperature is selected to ‘Cold' automatically.
4Press the ‘Start/Pause' button.
• The washer will be operated with locking Door and supplying water.
* ONLY WASH
1Put the laundry into the Drum and close the Door.
2Press the Power button.
• The LED shows only ‘- --' signal.
3Select the ‘SPIN CONDITION' you want by pressing ‘SPIN' button.
• The water temperature is selected to ‘Cold' automatically.
4Press the ‘Start/Pause' button.
• The washer will be operated with locking Door.
* ONLY SPIN
 
						

							E-24
Guide for other useful programs (cont.)
NOTE  
 • Do not use the detergent and softener.
 • Cold water tap should be opened.
 •  
After finishing this program,   is showed on PCB board alternately and the smoothing creases 
program is conducted during 30 minute and then power is OFF.
 • 'DELICATE', 'Quick 20', 'Tub Clean' and 'Drain' program are not selected with 'DRY'.
 • Be careful the high temperature of laundry when put out clothes.
 •  
A little shrikage and deformation will be possibly happened after drying, so check clothes whether dry or not 
previously
 • If the dry performance is poor, change the selecting temperature.
 • If youn want to dry with wash, after selecting program, press the 'DRY' button then press 'Start/Pause' button.
1Put the laundry into the Drum and close the Door.
2Press the Power button.
• The LED shows only ‘- --' signal.
3
Select the ‘DRY CONDITION' you want by pressing ‘DRY' button.
As this button is pressed, the dry condition is selected by ‘Cupboard' → ‘Very'
→ ‘Time(1:00, 2:00, 3:00, 4:00)' → OFF → ‘Low Temp' → ‘Iron' → ‘Cupboard'
4Press the ‘Start/Pause' button.
• The washer will be operated with locking Door.
* DRY (FOR DWC-LD141X)
 
						

							E-25
Guide for other useful programs (cont.)
NOTE  
 • The water temperature selecting is possible during this process.
1
Put the laundry into the Drum and put softerner into the detergent case.
Then close the Door.
• Softener should be below ‘MAX’ level.
2Press the Power button.
• The LED shows only ‘- --’ signal.
3
Press the ‘RINSE+SPIN’ button.
•  
‘800’ rpm spin speed and ‘COLD’ water temperature are selected automatically.
•  
If you want to change Spin condition, press each corresponding button.
4Press the ‘Start/Pause’ button.
• The washer will be operated with locking Door.
* RINSE+SPIN (FOR DWD-LD141X)
 
						

							E-26
Maintenance
Proper care of your washer can extend its life. This section explains how to care for your washer properly 
and safely.
Cleaning your washer
Winter storage or moving care
Install and store your washer where it will not freeze. Because some water may stay in the
hoses, freezing can damage your washer.
If you store or move your washer during freezing weather, winterize it.
Non-use or vacation care
Operate your washer only when you are at home.
If you are on vacation or don’t use your washer for an extended period of time, you should:
• Unplug the power supply cord or turn off eletrical power to the washer.
• Turn off the water supplier to the washer.
  This helps avoid accidental flooding (due to a water pressure surge) while you are away.
To winterize washerTo use washer again
• Turn off water faucet.
• Disconnect and drain water inlet hoses.
•  Run washer on a drain and spin setting                        (see page 10) for 1 minute.
• Unplug the power supply cord. • Flush water pipes and hoses.
• Reconnect water inlet hoses.
• Turn on water faucet.
• Reconnect power supply cord.
Exterior
Interior
Wipe up detergent, bleach, and other spills with a 
soft, damp cloth or sponge as they occur.
Occasionally wipe the outside of the washer to    
keep its looking like new one. Clean interior with 250ml of chlorine bleach       
mixed with 500ml of detergent.
Run washer through a complete cycle.
Repeat this process if necessary.
Remove pins, clips, coins, bolts, nuts, etc from pockets.  Failing 
which can cause damage to the drum assembly, pump, etc.
 
						

							E-27
How to clean the filter
Cleaning the detergent case
* After a while detergent and fabric softeners leav;e a deposit in the case;     
- It should be cleaned from time to time with a jet of running water.     
-  If necessary it can be removed completely from the machine by pressing the catch downwards and by  pulling it out.     
- To facilitate clean ing, the upper part of the fabric softener compartment can be removed.   
*  Detergent can also accumulate inside the recess which should be cleaned occasionally with a brush.
*  Once you have finished cleaning, replace the case and run a rinse cycle without laundry.
Cleaning the water inlet filter
Clean the filter when water leaks from the water inlet.
-:   Pull the power plug 
out before cleaning it. -<
  Turn off the water 
supply to the washer 
and separate the inlet 
hose. ->
  Pull the inlet filter out. -@  Remove the dirt from 
the inlet filter with a 
brush.
Filter Frame
Lint Filter
FILTER CONTAINER
CAP
CASE
FILTER
CAP
CAPFILTER
CASE
GUIDE
RI B
SUI T
CAP
CAP
Filter Frame
Lint Filter
FILTER CONTAINER
CAP
CASE
FILTER
CAP
CAPFILTER
CASE
GUIDE
RI B
SUI T
CAP
CAP
Filter Frame
Lint Filter
FILTER CONTAINER
CAP
CASE
FILTER
CAP
CAPFILTER
CASE
GUIDE
RI B
SUI T
CAP
CAP
Cleaning the drain filter
• This drain filter is used to screen the foreign stuffs s uch as threads, coins, pins, buttons etc..
• If the drain filter is not cleaned at proper time(every 10 times o f use), drain problem could be caused.
 CAUTION  Be careful when draining if the water is hot.
-:  Open the lower cover( ƒ) by 
using a coin. Turn the cap 
hose( „) to pull out the hose. 
Pull out the hose maximally. 
(About 13~14cm.)  -<
  Unplug the cap hose( „), 
allowing the water to flow out.  
At this time use a vessel to 
prevent water flowing on to the 
floor. When water does not flow 
any more, turn the pump filter 
( … ) open to the left. ->
  Remove any foreign material 
from the pump filter( …). After 
cleaning, turn the pump filter 
clockwise and insert the cap 
hose( „) to the original place.
    Close the lower cover.
232
3
1
100about
13~14cm
about
13~14cm
232
3
1
100about
13~14cm
about
13~14cm
232
3
1
100about
13~14cm
about
13~14cm
 
						

							E-28
Removing stains
Stained, heavily-soiled, or greasy items may need to be prewashed or soaked for best results.
Soaking helps remove protein-type stains like blood, milk or grass. Prewashing helps loosen soil before 
washing.
Stain removal rules
• Use warm water for soaking or prewashing stained laundry. Hot water can set stains.
• Most stains are easier to remove when they are fresh.
•  
Before treating any stain, find out what kind of stain it is, how old the stain is, what kind of fabric it is, and 
whether the fabric is colorfast. (Check the care label)
• Washing and drying can set some stains.
• Start with cold or warm water. Hot water can set some stains.
• When bleach is recommended, use a bleach that is safe for the fabric.
•  
Put the stained area face down on a paper towel or white cloth. Apply the stain remover to the back of the 
stain. This forces the stain off fabric instead of through it.
Stain removal guide
STAINTO REMOVE
BloodRinse immediately in COLD water.
If stain remains, soak in cold water with an enzyme prewash.
Chewing gumUse ice in plastic bag to harden the gum.
Scrape off what you can and the sponge with white spirits.
Cocoa, ChocolateSponge with COLD water and soak in an enzyme prewash.
If stains persist, rub in a little detergent and rinse in cold water.
CoffeeBlot up quickly and rinse out in COLD water.
Rub in a little detergent and wash in the maximum temperature allowed for the fabric type.
Cream/Milk
Ice cream
Rinse in COLD water and wash normally.
If stain is still apparent, sponge with white spirits.
DeodorantRub affected area with white vinegar and then rinse out in COLD water.
Sponge with white spirits. Treat stiffened areas with enzyme prewash.
EggSoak in a COLD enzyme prewash, rinse and wash normally.
Fabric/SoftenerRub affected area with bar soap and wash normally.
Fruit stainsTreat as soon as possible by sponging with COLD water.
Rub a little detergent on the stain and wash normally.
GrassSponge with white spirits. Rub in an enzyme prewash and wash as normally.
Grease and oilLay the affected area face down on an absorbent cloth and work from the back.
Sponge with white spirits or dry cleaning fluid. Wash normally.
Iron or rustApply lemon juice and salt and place in the sun. Wash normally.
LipstickSponge with white methylated spirits and wash normally.
MildewWash in WARM water and detergent.
Moisten area with lemon juice, dry in the sun and wash normally.
If stain persists and the fabric allows, use a bleach.
MudBrush off any dry mud. Rinse in cold water.
If stain persists rub in a little detergent and wash normally.
Paint-oil basedScrape off any fresh paint and sponge with a non flammable dry cleaning fluid and wash normally.
Paint-water basedTreat while still wet, rinse in WARM water and wash normally.
Scorch marksDampen a cloth with hydrogen peroxide, lay it over the affected area and press
with a fairly hot iron.
 
						

							E-29
Trouble shooting
PROBLEMCHECK POINT
•  
The washer will not operate at 
all.
• Is there a power failure?
• Is the power cord correctly connected to an electric outlet?
• Did you turn on the power?
• Did you press Start/Pause button?
• Is there correct amount of laundry in the washer?
• Water is not supplied
          Error display    
• Did you connect the inlet hose and open the water tap?
• Is the inlet hose or the water tap frozen?
• Is the water supply shot off?
• Is there any foreign matter blocking up the inlet hose filter?
• The washer will not drain 
          Error display               
• Is the drain hose frozen or blocked up by dirt?  
• Is the drain hose kinked or deformed? 
• Is the end of the drain hose immersed in water?
• Is there excessive dirt inside the drain filter?
• The washer will not spin  
          Error display               
• Is the clothes in the drum collected on one side?
• Is the washer installed on an uneven floor or is the vibration serious?
• Is the door open? (The lamp “” will light up in this case.)
• The washer will stop during 
spinning .
• Spinning is insufficient.     
          Error display        
      
 Is the filter of the drain pump clogged?
• Is the drain pump operated?
• Did you use the proper amount of detergent?
• Is the drain hose  placed higher than 1m above floor?
• Vibrating and too noisy• Is the washer installed on an uneven floor?
• Have all the transit bolts removed?
Most problems are easily solved if you understand the cause.
Check the following list for problem before calling for service.
If the error mode such as IE, OE, UE were displayed on the control part, in order to solve these problem, first 
turn off the power of the washing machine and then turn on the power pressing Power button.
If PFE error mode was displayed on the control part, in order to solve this problem, first turn off the power of 
the washing machine, second turn on the power pressing Power button, third press SPIN button and last 
press Start/Pause button.
These cases are not malfunctions;
• The sound “wing” heard during water supply is the operating sound made by the water inlet valve.  
Trouble shooting
 
						

							E-30
Specification
MODELDWC-LD141XDWD-LD141X
Dimension (mm)600 X 645 X 850
Maximum mass of textile (kg)8.5Kg
Unit Weight (net/gross)76/8069/73
Standard Water Consumption67 ℓ
Spin Speed (RPM)MAX 1400
Operating Water Pressure0.03MPa  ~ 0.8MPa (0.3kgf/cm2 ~ 8kgf/cm2)