Daewoo Dlp 32c3 Instruction Manual

							Name of 
Each Part
21
Rear Panel
HDMI INPUT AV1 AV2
PC INPUT    AUDIO
S-VHS
AV3 L - AUDIO - R
OPTICAL UP-GRADE PCRT
COMPONENTPr
RLPb Y
Side Panel
Side and Rear Panel

						

							Parts of the Remote
Controller
22
This remote controller is universal; thus, it may be convertible for TV, Video, CTV, etc.
1.  (MUTE) : Press this button, and the sound goes off.
Press again, and the sound returns.
2.  (POWER) : TV on/off button in Stand-By mode.
3.  PICTURE MODE : Picture modes changes as follows :
Normal  => Movie => Favourite => Normal
4.  SOUND MODE : Using the this button, Select the
desired sound mode.
Favourite => News => Music
5.  MULTIMEDIA : Each time you press this button, the TV
will cycle through:
PC => HDMI => Component =>PC
6. 
: Each time you press this button, the TV will cycle
through : TV => AV1 => AV2 => AV3/S-Video => TV
7.  ASPECT : Select screen aspect ratio :
16:9 
=> 14:9 => 4:3 => Panorama => Zoom1 => Zoom2
=> Auto => 16:9 
Note. : When current mode is multimedia ( PC, HDMI,
Component), the aspect only works as the 16:9 mode.
8. RECALL : The present modes(TV, Video, Component, PC)
and Signal information for 4 seconds.
In TV mode, the
Programme number, Sound, and Clock.
9.  : changes channels on your TV or move the cursor
(UP / DOWN) in the menu.
10.  : Adjust the volume or move the cursor (LEFT /
RIGHT) in the menu.
11. MENU : Menu display button.
12. PREV PR : Previous PROGRAMME button in TV mode.
13. OK : Auto Tuning Start and Manual Tuning Store.
14. 
P.MODE : Using this button, Select either POP On or Off.
Note. : This button also uses channel skip and teletext.
15. P.STILL : Using this button, you can freeze the sub screen
in POP mode.
Note. : This button also uses channel move and teletxt.
16. P.SWAP : Using this button, you can swap the main
screen for sub screen.
Note. This button also uses channel delete and teletxt.
17. P.INPUT : Sub Screen input mode change as follows
POP table mode.
Note. This button is also used in teletxt mode.
VOL
PR
MUTE
PICTURE
P.MODE
STILL
3D PANORAMA P.PR
P. P R
LOCK SLEEPP.STILL P.SWAP P.INPUT ASPECTSOUND
POWER
RECALL
PREV PROK
MULTIMEDIA
MENUV
O
LV
O
L PR
PR
123
456
789
0
X?
DYNAMIC BASS
 
						

							Parts of the remote
controller
23
18. DYNAMIC BASS : Using this button, you can enhance
the bass.
19. 3D PANORAMA : Using this button, you can listen to
the virtual surround sound.
20.  : When sub screen is RF(TV) mode in the POP,
you can change PROGRAMMES using this button.
21.  : You can select sound mode in Mono, 
Stereo,
Dual1, Dual2,  NiCAM STEREO. It works only in TV mode.
22. STILL : Press this button to freeze the picture.
23. NUMBER : Press the numbers on this board, you can
select PR directly in TV mode.
Note. When the current state is ST-BY, you can turn on the
TV using a digit key. Then, a PROGRAMME is
selected according to digit number.
24. LOCK : This prevents the use of the TV set without the
remote control.
25. SLEEP : Sleep Timer setting.
SLEEP TIMER : OFF
=> 10=> 20=> 30=> 40=> 50=>
60=> 70=> 80=> 90=> 100=> 110=> 120=> OFF 
26. Teletext : see page 45.
Inserting Batteries into the Remote Control Unit
To load the batteries, turn the remote control handset over
and open the battery compartment. Insert the batteries (Two
1.5v, type AAA).
Make sure that the polarity matches with the (+) and (-)
marks inside of the battery compartment.
Note: To avoid damage from possible battery leakage,
remove the batteries if you do not plan to use the
remote control handset for an extended period of time.
P.PR
MUTE
PICTURE
P.MODE
STILL
3D PANORAMA P.PR
P. P R
LOCK SLEEPP.STILL P.SWAP P.INPUT ASPECTSOUND
POWER
RECALL
PREV PROK
MULTIMEDIA
MENUV
O
LV
O
L PR
PR
123
456
789
0
X?
DYNAMIC BASS
 
						

							Method To Use
Basic Menu
24
Picture
Screen
Sound
Function
Install:  Adjust Mode, Brightness, Contrast, Colour, Sharpness and Tint(NTSC only).
:  Adjusts Aspect, Position(PC mode only)
:  Adjusts Mode, Equalizer, 3D Panorama, Dynamic Bass and Balance.
:  Adjusts Language, Timer and Child Lock.
:  Adjusts Auto Tuning, Manual Tuning, Fine Tuning and Edit.
PositionAccessMENUExit
Mode
Brightness
Contrast
Colour
Sharpness
Tint
Colour TempNormal
Normal
32
58
32
32
0
Picture
Sound
Function
Install
Screen
2. Press the "PR" button.
• You may setup according to the directions on the
screen after selecting the desired item by pressing the
“
PR” button.
• If the setup is completed, exit from the menu by
pressing the “MENU” button.
MENUV
O
LV
O
L PR
PR
PositionAccessMENUExit
Mode
Brightness
Contrast
Colour
Sharpness
Tint
Colour TempNormal
Normal
32
58
32
32
0
Picture
Sound
Function
Install
Screen
- The basic menu appears on the screen if you press the “MENU” button of the remote control.
- There are 5 items Picture, Screen, Sound, Function, and Install in the basic menu.
- 
Each item has sub-items under it. If the desired item is selected, the relevant sub-items are displayed upward.
1. Press the "MENU" button.
• The main menu appears if you press the “MENU” button.
Basic Menu
MENUV
O
LV
O
L PR
PR
 
						

							To Watch TV
25
- Buttons with same name in the main body performs the same function.
MUTE
PICTURE
P.MODE
STILL
3D PANORAMA P.PR
P. P R
LOCK SLEEPP.STILL P.SWAP P.INPUT ASPECTSOUND
POWER
RECALL
PREV PROK
MULTIMEDIA
MENUV
O
LV
O
L PR
PR
123
456
789
0
X?
DYNAMIC BASS
When pressing the Program button
• Select two digits if using the number button for channel
selection.
For example, to watch channel No.9,
Press the number button 0 and 9.
If pressing only number 9, it takes a longer time to select
the channel.
Press the " " button of the front side of the set or
Remote controller .
• The buttons of the remote control and the main body
operate only  when AC power is turned on. 
Note: You can also turn on the TV using “
PR” or
digit key in the ST-BY mode.
To suddenly turn sound off
• Press the “MUTE”( ) button.
• No sound is heard if “MUTE( )” is displayed on the
screen.
• Sound is heard again if you press the “MUTE( )”
button once again.
For example, please use this button when telephone rings
or when guest comes while watching TV.
Check of TV operation status
• If pressing the “RECALL” button, status of channel or
broadcasting being currently watched or entry status of
video component is displayed on the screen.
On/Off, Number, Mute, Recall, , 

						

							To Watch TV
26
POWER
POWER
MENUV
O
LV
O
L PR
PR
MENUV
O
LV
O
L PR
PR
PR 19Clock  12 : 00 Mono
1. Press the “ ” button of the main body.
• The Stand By LED lamp turns on in red colour. 
• Press “
/” button of the main body or “POWER”
button of the remote control.
• The Stand By LED lamp on the front panel begins to
fliker in red and green colour and the TV turns on.
2. Press the “PR” button.
• Select the desired program by pressing the “
PR”
button or the number button.
3. Adjust volume.
•Sound reduces by pressing the  “
VOL” button.
• Sound increases by pressing the “VOL
” button.
Note :Sound mutes by pressing the “MUTE”( ) button. 
4. Press the “POWER” button for turning the TV off.
• TV turns off and the power lamp changes to red
colour. 
7ownloadeda:roma‘Vd*anualucoma*anuals 
						

							Setting Up TV
Stations
27
- All stations that can be received are stored by this method. It is recommended that you use Auto tuning during
installation of this set.
OK   Start Country SetMENUExit
Auto Tuning
Country Set
PR 19  PAL / SECAM Italy
PositionMove Skip DeleteMENUExit
EditPr
01
02
03
04
05
06
07
08
09
10Ch.
- --
- --
- --
- --
- --
- --
- --
- --
- --
- --Pr
21
22
23
24
25
26
27
28
29
30Ch.
- --
- --
- --
- --
- --
- --
- --
- --
- --
- --Pr
11
12
13
14
15
16
17
18
19
20Ch.
- --
- --
- --
- --
- --
- --
- --
- --
- --
- --
PositionAccessMENUExit
Mode
Brightness
Contrast
Colour
Sharpness
Tint
Colour TempNormal
Normal
32
58
32
32
0
Picture
Sound
Function
Install
ScreenMENUV
O
LV
O
L PR
PR
MENUV
O
LV
O
L PR
PR
MENUV
O
LV
O
L PR
PR
OK
MENUV
O
LV
O
L PR
PR
SetupPicture
Function
Install Sound
Screen
1. Press the “MENU” button to select the Install menu.
• Move the selection bar to the Install menu with 
“
PRbuttons. 
2. Select the "Auto Tuning". 
• Place the selection bar on Auto Tuningand press the 
“VOL
button.
3. Select the countr y you require with the “
“
button.
• After selecting the country, To start Auto Tuning press
the “OK” button.
4. Please wait until the Edit menu appears.
• If you don’t want to edit the programs now, escape
from the menu with the “MENU” button. 
Auto Tuning

						

							Setting Up TV
Stations
28
MENUV
O
LV
O
L PR
PR
MENUV
O
LV
O
L PR
PR
123
456
789
0
OK
MENUV
O
LV
O
L PR
PR
SetupPicture
Function
Install Sound
Screen
OK   StoreAccessPr ChangeMENUExit
Manual Tuning
Pr 01  PAL / SECAM 
Note :
• If you are unable to get any programs using Auto Tuning because of a poor broadcasting signal, it is
possible to store the Manual tuning.
• When you enter Manual Tuning after Auto Tuning in France or Swiss, if present channel is SECAM L/L',
TV set can only search SECAM L/L'.
• If you enter by other than by SECAM L/L' signal, TV set can search every by SECAM L/L' signal except
SECAM L/L'.
• You can change the Programme number in the Edit mode.
• Manual tuning does not support this function.
Manual tuning
1. Press the Number buttons(0~9) or the “PR”
button to select a program number you want.
2. Locate the selection bar on the Manual tuning at the
Install menu.
• Press the “MENU” button to select the Install menu. 
• Move the selection bar to the Install menu with 
“
PR” buttons. 
• Place the selection bar on Manual Tuningand press
the “VOL
“ button.
3. Press the “
VOL” buttons.
• A tuning screen will appear and cursor will move from
left to right / from right to left. If you want to stop
tuning press the “MENU” button. 
• After searching a station, you must press the “OK”
button to store the Program.
7ownloadeda:roma‘Vd*anualucoma*anuals 
						

							Setting Up TV
Stations
29
The Setup menu shows you information as follows:
- Picture information: PAL, SECAM, and SECAM-L
- Sound information: L, DK3, DK2, DK1, I, BG
- Station name, Program number and Real channel number.
1. Searching for channels in the Setup menu
• Press the “
PR“ buttons to select a program number
you want.
• Move to SETUP in the Install menu.
• Select the colour and sound system which you want.
• Search a real channel with “
PR“ buttons. 
2. Enter a station name 
• Move to SETUP in the Install menu.
• Move the cursor to name by pressing “
VOL“
buttons.
• You can enter a station name with the “
PR“ and
“
VOL“ buttons.
3. Fine tuning                                   
• Move to SETUP in the Install menu.
• Move the cursor to Fine Tuning by pressing “
PR“
buttons.
• Adjust the fine tuning with the “
VOL“ buttons.
Note :• If you are unable to get a good picture or Sound
because of a poor broadcasting signal, 
adjustment of the fine tuning might improve it.
• The alphabet below OSD in the Setup menu only
display on english.
• This part does not other language except english.
Program
Channel
Name
System
Sound
Fine Tuning
_ A B C D E F G H I J K L M N O P Q R
S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9
18- --
PALDK10
- - - - -Picture
Function
Install Sound
Screen
SetupPicture
Function
Install Sound
Screen
Program
Channel
Name
System
Sound
Fine Tuning
_ A B C D E F G H I J K L M N O P Q R
S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9
18- --
PALDK10
- - - - -Picture
Function
Install Sound
Screen
MENUV
O
LV
O
L PR
PR
MENUV
O
LV
O
L PR
PR
MENUV
O
LV
O
L PR
PR
Setup

						

							Setting Up TV
Stations
30
The Edit menu shows you information as follows:
- Program position assignment: Program number and Station name, Real channel number.
- Skip information: Red (Skip Yes), White (Skip No)
MENUV
O
LV
O
L PR
PR
PositionMove Skip DeleteMENUExit
EditPr
01
02
03
04
05
06
07
08
09
10Ch.
- --
- --
- --
- --
- --
- --
- --
- --
- --
- --Pr
21
22
23
24
25
26
27
28
29
30Ch.
- --
- --
- --
- --
- --
- --
- --
- --
- --
- --Pr
11
12
13
14
15
16
17
18
19
20Ch.
- --
- --
- --
- --
- --
- --
- --
- --
- --
- --
P.MODE
STILL
3D PANORAMA P.PR
P. P R
P.STILL P.SWAP P.INPUT
123
DYNAMIC BASS
MENUV
O
LV
O
L PR
PR
PositionMove Skip DeleteMENUExit
EditPr
01
02
03
04
05
06
07
08
09
10Ch.
- --
- --
- --
- --
- --
- --
- --
- --
- --
- --Pr
21
22
23
24
25
26
27
28
29
30Ch.
- --
- --
- --
- --
- --
- --
- --
- --
- --
- --Pr
11
12
13
14
15
16
17
18
19
20Ch.
- --
- --
- --
- --
- --
- --
- --
- --
- --
- --
P.MODE
STILL
3D PANORAMA P.PR
P. P R
P.STILL P.SWAP P.INPUT
123
DYNAMIC BASS
MENUV
O
LV
O
L PR
PR
PositionMove Skip DeleteMENUExit
EditPr
01
02
03
04
05
06
07
08
09
10Ch.
- --
- --
- --
- --
- --
- --
- --
- --
- --
- --Pr
21
22
23
24
25
26
27
28
29
30Ch.
- --
- --
- --
- --
- --
- --
- --
- --
- --
- --Pr
11
12
13
14
15
16
17
18
19
20Ch.
- --
- --
- --
- --
- --
- --
- --
- --
- --
- --
P.MODE
STILL
3D PANORAMA P.PR
P. P R
P.STILL P.SWAP P.INPUT
123
DYNAMIC BASS
Edit
1. Deleting the program positions.
• Move to EDITin the Install menu. 
• Move the selection bar to program number to
delete with the “
PR” or “VOL“ buttons.
• Press the Delete(Yellow) button.
2. Moving the program positions
• Move to EDITin the Install menu.
• Press the Move(Green) button. The colour of
"Move" Character will be changed to Red from
White.
• Move the selection bar to a new program number.
• Press the Move (Green) button again, then the
programs are changed.
3. Skipping the Programs
• Move to EDITin the Install menu. 
• Move the selection bar to the program number you
want to skip
• Press the skip (Red) button, then the colour of the
program number and channel will be changed to
Red from White.
• The skipped program number will be displayed as
red in the EDITmenu.
7ownloadeda:roma‘Vd*anualucoma*anuals