compaq evo n115 User Manual

							Remova l and Replacement Procedures
Maintenance and Ser vice Guide 5–43
2. Release the ZIF connector 1 to which the diskette drive cable 
is connected and disconnect the cable 
2 from the system 
board (Figure 5-36).
3. Remove the silver TM2.0 × 5.0 screw 
3 that secures the 
diskette drive to the base enclosure.
Figure 5-36. Disconnecting the Diskette Drive Cab le and 
Remo ving the Diskette Drive Scre ws
263816m1.book  Page 43  Friday, January 25, 2002  2:14 PM 
						

							5–44Maintenance and Service Guide
Remo va l and Replacement Procedures
4. Lift up the right side of the diskette drive 1 until the drive 
rests an angle (Figure 5-37).
5. Slide the diskette drive to the right 
2 and remove it from the 
base enclosure.
Figure 5-37. Remo ving the Diskette Drive
263816m1.book  Page 44  Friday, January 25, 2002  2:14 PM 
						

							Remova l and Replacement Procedures
Maintenance and Ser vice Guide 5–45
6. Release the ZIF connector 1 to which the diskette drive cable 
is connected and disconnect the cable from the diskette 
drive
2 (Figure 5-38).
✎The diskette drive cable is included in the Cable Kit (spare part 
number 254120-001).
Figure 5-38. Remo ving the Diskette Drive Cab le
Reverse the above procedure to install the diskette drive.
263816m1.book  Page 45  Friday, January 25, 2002  2:14 PM 
						

							5–46Maintenance and Service Guide
Remo va l and Replacement Procedures
5.16 Charger Board
1. Prepare the computer for disassembly (Section 5.3) and 
remove the following components:
a. Optical drive (Section 5.7)
b. LED cover (Section 5.8)
c. Keyboard (Section 5.9)
d. Display (Section 5.10)
e. Heat spreader (Section 5.11)
f. Top cover (Section 5.14)
g. Diskette drive (Section 5.15)
Charger Board
Spare Part Number Information
Charger board 254109-001
263816m1.book  Page 46  Friday, January 25, 2002  2:14 PM 
						

							Remova l and Replacement Procedures
Maintenance and Ser vice Guide 5–47
2. Remove the silver TM2.0 × 5.0 screw 1 that secures the 
charger board to the system board (Figure 5-39).
3. Lift up on the back edge of the charger board 
2 to disconnect 
it from the system board.
Figure 5-39. Disconnecting the Char ger Boar d
263816m1.book  Page 47  Friday, January 25, 2002  2:14 PM 
						

							5–48Maintenance and Service Guide
Remo va l and Replacement Procedures
4. Swing the right side of the charger board up and to the left1 
until the hard drive connector clears the system board 
(Figure 5-40).
5. Remove the charger board 
2.
Figure 5-40. Remo ving the Charger Boar d
Reverse the above procedure to install the charger board.
5.17 Left Side Panel
✎The left side panel is included in the Plastics and Hardware Kit 
(spare part number 254121-001).
263816m1.book  Page 48  Friday, January 25, 2002  2:14 PM 
						

							Remova l and Replacement Procedures
Maintenance and Ser vice Guide 5–49
1. Prepare the computer for disassembly (Section 5.3) and 
remove the following components:
a. Optical drive (Section 5.7)
b. LED cover (Section 5.8)
c. Keyboard (Section 5.9)
d. Display (Section 5.10)
e. Heat spreader (Section 5.11)
f. Top cover (Section 5.14)
g. Diskette drive (Section 5.15)
2. Remove the following fasteners (Figure 5-41):
a. Three silver TM2.0 × 5.0 screws 
1
b. One silver HM5.0 × 13.0 standoff 2
3. Slide the left side panel to the left to remove it from the base enclosure 
3.
Figure 5-41. Remo ving the Left Side P anel
Reverse the above procedure to install the left side panel.
263816m1.book  Page 49  Friday, January 25, 2002  2:14 PM 
						

							5–50Maintenance and Service Guide
Remo va l and Replacement Procedures
5.18 Right Side Panel
✎The right side panel is included in the Plastics and Hardware Kit 
(spare part number 254121-001).
1. Prepare the computer for disassembly (Section 5.3) and  remove the following components:
a. Optical drive (Section 5.7)
b. LED cover (Section 5.8)
c. Keyboard (Section 5.9)
d. Display (Section 5.10)
e. Heat spreader (Section 5.11)
f. Top cover (Section 5.14)
263816m1.book  Page 50  Friday, January 25, 2002  2:14 PM 
						

							Remova l and Replacement Procedures
Maintenance and Ser vice Guide 5–51
2. Remove the three silver TM2.0 × 5.0 screws 1 that secure the 
right side panel to the base enclosure (Figure 5-42).
3. Lift the slot 
2 on the alignment arm on the bezel off of the 
circular slot 
3 on the base enclosure.
4. Slide the right side panel to the right to remove it from the  base enclosure 
4.
Figure 5-42. Remo ving the Right Side P anel
Reverse the above procedure to install the right side panel.
263816m1.book  Page 51  Friday, January 25, 2002  2:14 PM 
						

							5–52Maintenance and Service Guide
Remo va l and Replacement Procedures
5.19 Speaker Assembly
1. Prepare the computer for disassembly (Section 5.3) and 
remove the following components:
a. Optical drive (Section 5.7)
b. LED cover (Section 5.8)
c. Keyboard (Section 5.9)
d. Display (Section 5.10)
e. Heat spreader (Section 5.11)
f. Top cover (Section 5.14)
g. Diskette drive (Section 5.15)
h. Left side panel(Section 5.17)
i. Right side panel (Section 5.18)
Speaker Assembly
Spare Part Number Information
Speaker assembly 254118-001
263816m1.book  Page 52  Friday, January 25, 2002  2:14 PM