Home > Casio > Watch > Casio Fe10 Manual

Casio Fe10 Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Casio Fe10 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 338 Casio manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							USER’S GUIDE 2428
    1
    •After you perform an operation in any mode, pressing B returns to the
    Timekeeping Mode.General GuideThe operational procedures for Modules 2428 and 2470 are identical. All of the
    illustrations in this manual show Module 2428.
    •Press B to change from mode to mode.  Each mode is explained in detail on
    the following pages.
    [Module 2470] [Module 2428]Timekeeping ModeTime Setting Mode Stopwatch Mode Alarm Mode
    Press .
    Backlight Precautions
    The backlight uses an EL (electro-luminescent) panel that causes the entire
    display to glow for easy reading in the dark.
    •The electro-luminescent panel that provides illumination loses power after
    very long use.
    •The illumination provided by the backlight may be hard to see when viewed
    under direct sunlight.
    •The watch may emit an audible sound whenever the display is illuminated.
    This is due to vibration of the EL panel used for illumination, and does not
    indicate malfunction.
    •Frequent use of the backlight shortens the battery life.
    Timekeeping Mode•In the Timekeeping Mode, press C to switch
    between the 12-hour and 24-hour formats.
    •In the Timekeeping Mode, press A to illuminate the
    display for a few seconds.
    •Day of the week is displayed as follows.
    SU: Sunday MO: Monday
    TU: Tuesday WE: Wednesday
    TH: Thursday F R :  Friday
    SA: SaturdayDay of the week
    Day
    Hour PM indicator
    Minutes
    Seconds
    Alarm ModeWhen the Daily Alarm is switched on, the alarm
    sounds for 20 seconds at the preset time each day.
    When the Hourly Time Signal is switched on, the
    watch beeps every hour on the hour.
    To set the alarm time
    1. Hold down A while in the Alarm Mode until the
    hour digits start to flash on the display.  The hour
    digits flash because they are 
    selected.
    2. Press A to change the selection in the following
    sequence.
    •Pressing A also illuminates the display.
    Hour Minutes
    Normal Alarm Mode (No digit flashes)
    •Once you reach the normal Alarm Mode, you have to hold down A again
    until the hour digits start to flash.
    3. Press C to increase the selected digits.  Holding down C changes the
    number at high speed.
    •The format (12-hour and 24-hour) of the alarm time matches the format you
    select for normal timekeeping.
    •When setting the alarm time using the 12-hour format, take care to set the
    time correctly as morning or afternoon (PM).
    4. After you set the alarm time, press A to return to the Alarm Mode.  At this
    time the Daily Alarm is switched on automatically.
    To stop the alarm
    Press A to stop the alarm after it starts to sound.
    Hourly time 
    signal on 
    indicator Mode indicator
    Hour
    Alarm on 
    indicator Minutes
    To switch the Daily Alarm and Hourly Time Signal on and off
    Press C while in the Alarm Mode to change the status of the Daily Alarm and
    Hourly Time Signal in the following sequence.
    [Alarm on Indicator/Hourly Time Signal on Indicator]
    Hourly Time
    Signal only Daily Alarm
    only Both off Both on
    To test the alarm
    Hold down C while in the Alarm Mode to sound the alarm.
    Stopwatch ModeThe Stopwatch Mode lets you measure elapsed time,
    split times, and two finishes.  The range of the
    stopwatch is 59 minutes, 59.99 seconds.Mode Indicator
    Split time 
    indicator Minutes
    Seconds
    1/100 second
    (a) Elapsed time measurement 
    StartStop Re-start Stop Clear
    StartSplit Split release Stop Clear
    StartSplit Stop Split release Clear (b) Split time measurement 
    (c) Split time and 1st-2nd place times
    First runner 
    finishes.Second runner 
    finishes.
    Record time of 
    first runner.Record time of 
    second runner.
    Time Setting Mode
    To set the time and date
    1. Use B to enter the Time Setting Mode.
    •The second’s digits flash because they are
    selected.2. Press A to change the selection in the following
    sequence.
    •Pressing A also illuminates the display.
    Seconds Hour
    Minutes
    Day of week Day
    Month
    Day of the week
    Day
    HourMinutes
    Seconds PM indicator
    3. While the second’s digits are selected (flashing), press C to reset the
    seconds to “00”.  If you press C while the second’s count is in the range of
    30 to 59, the seconds are reset to “00” and 1 is added to the minutes.  If the
    second’s count is in the range of 00 to 29, the minute’s count is unchanged.
    4. While any other digits (besides seconds) are selected (flashing), press C to
    increase the number.  While the day of the week is selected, pressing C
    advances to the next day.  Holding down C changes the current selection at
    high speed.
    5. After you set the time and date, press B to return to the Timekeeping Mode.
    •If you do not operate any button for a few minutes while a selection is
    flashing, the flashing stops and the watch goes back to the Timekeeping
    Mode automatically. 
    						
    All Casio manuals Comments (0)

    Related Manuals for Casio Fe10 Manual