Canon Imageformula Dr C225 User Guide

21
Chapter 4 Connecting the Scanner
###HOME > Chapter 4 Connecting the Scanner###
Connect the scanner to the computer and power outlet.
Connecting the Scanner to the Computer........................................ 21
Turning the Power ON ........................................................................ 22
Connecting the Scanner to the Computer
###HOME > Chapter 4 Connecting the Scanner > Connecting the 
Scanner to the Computer###
Connect the scanner to the computer and the power supply.
zDo not...

22
Turning the Power ON
###HOME > Chapter 4 Connecting the Scanner > Turning the Power 
ON###
The power of the scanner can be turned ON and OFF with the power 
button on the front of the scanner.
1Make sure that the scanner and computer are connected properly.
2Press the power button.
The power button lights blue when the power turns ON.
You can secure the cables to the back of the scanner. Make sure 
there is sufficient slack in the cable when doing so to reduce stress 
on the connector.
 

23
Turning Off the Power
Press and hold the power button until the indicator goes out.
When the scanner is turned on for the first time, the balloon 
message shown below appears on the Windows task bar. If you 
wait a while, automatic scanner recognition will end and the 
scanner will become ready to use.
When the scanner is properly connected to the computer, the   
(CaptureOnTouch) icon appears on the taskbar as follows.
If the taskbar icon appears as   or   the scanner is not properly 
connected to...

24
Chapter 5 Placing Documents
###HOME > Chapter 5 Placing Documents###
This section describes how to load a document for scanning.
Documents .......................................................................................... 24
Switching the Feed and Eject Methods ............................................ 26
Placing Documents for Standard Feeding ....................................... 26
Placing Documents for Non Separation Feeding ............................ 29
Placing Cards...

25
Scanning the following types of documents can cause a paper jam or 
malfunction. To scan such a document, make a photocopy of the 
document and then scan the photocopy.
Business Card
Card (plastic or laminated)
„Use the straight path when scanning cards.
„If you place cards to be fed vertically, they may not be ejected 
properly, and cards that get jammed may be damaged when you 
remove them. Take care of the orientation when placing cards.
„Embossed cards may not be able to be scanned correctly,...

26
Switching the Feed and Eject Methods
###HOME > Chapter 5 Placing Documents > Switching the Feed and 
Eject Methods###
Use the two levers on the scanner to switch the feed and eject 
methods based on the type of document you are scanning.
The feed and eject methods and lever positions for each document type 
are as follows.
Placing Documents for Standard Feeding
###HOME > Chapter 5 Placing Documents > Placing Documents for 
Standard Feeding###
Ordinarily, standard feeding should be used when scanning...

27
3When scanning long documents, pull out the feed extension plates 
and eject support.4Set the feed selection lever and the eject selection lever.
Set the feed selection lever to the standard feeding position (lower position).
Set the eject selection lever to the U-turn path position ( ).
When scanning documents that contain both standard paper and plastic cards, 
use the straight path.
5Adjust the document guides to fit the width of the document to be 
scanned.
 

28
6Place the document.
Insert the document in the feed tray so that the front is facing forward and the 
top is facing upward.
After inserting the document in the document feeder, align the document 
guides with both edges of the document.
zWhen placing documents into the feed tray, take care not to 
cut your hands on the edges of the paper.
zMake sure that the document does not exceed the loading limit 
marks ( ) on the document guides. Up to 30 pages of ordinary 
plain paper (80 g/m
2) can be loaded...

29Placing Documents for Non Separation 
Feeding
###HOME > Chapter 5 Placing Documents > Placing Documents for Non 
Separation Feeding###
When scanning a thick document one page at a time or scanning a 
document that has multiple pages fastened together, set document 
feeding to non separation mode. This enables the placed document 
to be scanned without the pages being separated, regardless of the 
number of pages.
1Set the feed selection lever and the eject selection lever.
Set the feed selection lever...

30
2Adjust the document guides to fit the width of the document.
3Place the document in the document feed tray.
zWith the straight path, documents are ejected at the front of 
the scanner. Do not place anything that will block output near 
the document eject area. Also, install the scanner on a smooth 
surface to enable documents to be smoothly ejected.
zWhen scanning multiple page documents that are fastened 
together, such as invoices, place the documents so that the 
edge that is fastened together is...