Canon Digital Ixus Wireless User Guide

99
Wireless Connection
2Attach the supplied compact power adapter 
to the wireless print adapter.
zInsert the compact 
power adapter cable 
firmly into the wireless 
print adapter’s DC IN 
terminal.
zAttach the compact 
power adapter CA-DC20 
if you are using a Canon 
PictBridge Compliant 
printer other than a 
CP710/CP510. You do 
not need to use the 
compact power adapter CA-DC20 if you are using 
CP710/510.
zAlways hold the side of the cable’s connector when 
removing the compact power adapter cable...

100
Connecting/Disconnecting
Setting up a wireless connection to a printer
1Slide the mode switch to   (playback)    (Wireless) Menu   [Connect/Disconnect]
See  Menus  and Settings  (p. 32).
zEven if you press the   button 
without displaying the menu in 
playback mode, the same screen 
will be displayed.
2After confir ming that [1.WA-1] is selected as 
the [Target Device], use the   or   buttons 
to select [Connect] and press   (or  ).
z The monitor will display 
“Connecting”, and soon the 
connection...

101
Wireless Connection
Ending the wireless connection
zIf   displays during wireless connection, it means that the 
connection is very good. The fewer the antennas displayed, 
the worse the wireless connection is. When   and the 
wireless lamp both blink, it indicates an extremely bad 
connection. In such a case, shorten the distance between 
the camera and the wireless adapter.
z Please be aware of the points below when using a wireless 
connection between the camera and a printer. Failure to 
follow...

102
Registering a target device
To set up a wireless connection to a printer using a wireless print 
adapter other than the supplied adapter, you will need to register 
the other adapter with the camera as a new target device.
Changing the wireless print adapter 
channel
If the wireless print adapter channel (useful frequency) is 
already in use by another device, change the channel to 
avoid interference from radio waves.
1Select the target device for which you 
wish to change the channel in [Target...

103
Wireless Connection
zWhen registering the wireless print adapter, make sure it 
is within 1 meter of the camera.
z If the registration fails, please refer to  List of 
Messages (p. 115).
z You can register up to 8 adapters with the camera.
2Slide the mode switch to   (playback)       
(Wireless) Menu   [Reg. Target Device].
See  Menus  and Settings  (p. 32).
3When the message “Press the SETUP 
button” is displayed in LCD monitor, press 
the wireless print adapter’s SETUP button 
within 10 seconds....

104
You can delete devices which you no longer use.
zYou cannot delete the wireless print adapter provided with 
the camera.
Deleting target devices
1(Wireless) Menu   [Delete Registration]
See  Menus  and Settings  (p. 32).
2Select the target device you wish to delete.
zUse the   or   button to select 
[Target Device], and the   or   
button to select the target device 
you wish to delete.
3Use the  ,  ,   or   button to select 
[Delete], then press  .
z If you want to cancel instead of deleting, select...

105
  Troubleshooting
Troubleshooting
Camera
Camera will not operate.
Power is not turned on.zPress the power button (Basic 
Guide p. 5).
Memory card slot/battery 
cover is open.zConfirm that the memory card slot/
battery cover is securely closed 
(Basic Guide p. 2).
Insufficient battery 
voltage (“Change the 
battery pack” message 
displays).zInsert a fully charged battery into the 
camera (Basic Guide p. 2).
zUse the AC Adapter Kit ACK-DC10 
(sold separately) (p. 123).
Poor contact between 
camera and...

106
LCD monitor
The display darkens.
The image on the LCD 
monitor will darken in 
strong sunlight or bright 
light.zThis does not constitute a 
malfunction and has no effect on 
images that have been shot.
Display flickers.
Display flickers when 
shot under fluorescent 
lighting.zThis is not a camera malfunction 
(flickering recorded in movies, but 
not in still images).
A bar of light (red, purple) appears on the LCD monitor.
Subject is too bright.zThis is a normal occurrence in 
devices containing...

107
  Troubleshooting
Noise displays./Subject’s movements are irregular.
Camera automatically 
lightened the image 
displayed on the LCD 
monitor to make it easier 
to see when shooting in 
a dark area (p. 21).zThere is no effect on the recorded 
image.
Shooting
Camera will not record.
Mode switch is set to   
(playback).zSet the mode switch to   (Rec.) or 
 (Movie) (Basic Guide p. 6).
Flash is charging.zWhen charging is complete, the 
indicator will light orange and you 
are free to start shooting (p....

108
Image is blurred or out of focus.
AF-assist Beam is set 
to [Off].z
In dark places where it is difficult for 
the camera to focus, the AF-assist 
Beam will emit to assist focusing. 
As the AF-assist Beam will not 
function when turned off, set it [On] to 
activate it  (p. 33). Take care not to 
obstruct the AF-assist Beam with your 
hand when used.
The camera moves when 
the shutter button is 
pressed. z
Setting the self-timer to   
(2 seconds) delays the shutter 
release for 2 seconds and allows...